Angled screw-in supports, R 1/4 o., for hose I.D. 8 mm, AF 14, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

1-ear hose clamp, Stainless steel 1.4301 (W4), Clamping range 7.0 - 9.0 mm, Belt width 6.0 mm

Push-in Y-fitting »Blue Series«, rotating, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Hose sleeve with ball nipple, for hose I.D. 13, Brass, Max. working pressure 25 bar, Max. operating temp.150 °C

Frequency:50 Hz
Speed:2930 1/min
Shaft Output:5097 W
Volume Flow:5742 m³/h
Pressure:Δp s2457 Pa
Pressure:Δp t2647 Pa
Density:43862 kg/m³
Sound Pressure:90 dB(A)

2X1,5Mmâ² Orange With Door Switch Weight:0,32

Single and Dual-Frequency
This version of Airmar’s M163 is available in two configurations. The first packs a 28 kHz, 2 kW array in a compact, SEALCAST™ housing. The second configuration uses nine, ceramic elements that resonate at both 28 kHz and 50 kHz and results in a very compact, dual-frequency transducer. The 75 kHz, M163 features an efficient highly-sensitive 19-element array. Its design is easier and less costly to install than magno-restrictive transducers requiring steel tanks. Both configurations have very high-efficiency and sensitivity for their size, resulting in excellent deep-water performance. The 33 kHz, 200 kHz, and 210 kHz, dual-beam transducers have conical beam patterns and minimal sidelobes that provide accurate depth measurements in both shallow and deep-water.

Applications
Shallow and deep-water survey
Commercial fishing vessels

Max. stack height : 170 mm
HSS-F-BA-154x047-0210-B
SKU: TBSP030210
Stock *: 0
Width: 154 mm
Sheet separators with ferrite magnets are suitable for separating sheets in the most common situations.

Permanent magnetic
For sheets up to 4 mm thick
Max. stacking height 490 mm
Steel enclosure
Ferrite magnet

Operation

Ferrite sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 60 Homologation Dimension D x H (mm) 50 x 120 Pcs x bag 50

Twin Cable / M8 STUD
The MK 450 capacitors are suitable for the heavy duty motor
applications.

Z42 – Z43 General features
Suitable for O41NCMAUX electrothermal actuator
Nominal pressure PN 16.
2-way valve in bronze.
3-way valve in nickel-plated brass.

Polyurethane timing belt T10 width 50mm Lw 1750mm 175 teeth 50 T10/1750
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Classical shape with trapezoid teeth. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. T timing belts only run on T pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16498700

Filling unit »FUTURA«, pneumatically actuated, Size 1, G 1/4, Exhaust G 1/4, Input pressure 2.5 - 16 bar, Temp. -10 °C to 50 °C
The filling unit protects devices connected downstream by ensuring a gradual build-up of pressure.
The unit consists of a 3/2-way valve including silencer and a filling valve (start-up valve).
It is connected and disconnected by means of the 3/2-way valve.
The filling time can be altered by turning the adjusting screw.

Adjust. angled screw conn., 360° swivel range, cone seal, female nut M36x2.0 i., Pipe ext. Ø 25, PN max. 400 bar, galvanised steel

Round cylinder, ISO 6432, double-acting, Magnet, Piston Ø 16, Stroke 125, M5, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

T-piece, 3x interior thread, G 1 1/4, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Straight screw-in fitting, G 1/2 o., Pipe exterior Ø 12 mm, PN max. 630 bar, A/F1 24, A/F2 27, galvanised steel, soft seal
Male connector, parallel male thread and soft seal, heavy type

Sintered bronze silencer »value line«, Slot, G 3/8, Operating pressure max. 10 bar, Operating temperature -10 °C to 200 °C
For reducing the exhaust noise generated by pneumatic equipment.

Standard pressure gauge, Double scale, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0-10 bar/145 psi, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Straight reducing supports, for hose I.D. 10/6 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Straight hose connection supports, for hose I.D. 8 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Standard pressure gauge, Double scale, Connection radial bottom, G 1/8, Goods class 1.6, Measurement range 0-25 bar/360 psi, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Hose clamp, Malleable cast iron, 2-part, with loose tongues, Clamping range 22 - 29 mm, for hose I.D. 13 (1/2")

Spur gear made of polyacetal resin die-cast with hub module 0.5 20 teeth tooth width 3mm outside diameter 11mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28102000

Locking assembly BAR stainless steel 1.4401 bore 18mm
Material: Stainless steel
1.4401 (SS316).
For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft.

Stainless steel.

For low torques.

Self-centering.

Slight axial offset possible during assembly. Fit, Surface:
Due to the special design of the BAR clamping set even rough fits can
be bridged with excellent self centering capacity. Shaft and hub up to
Quality h8/H8. Surface finish for shaft and hub 10µm.

Frequency:50 Hz
Speed:1455 1/min
Shaft Output:961 W
Volume Flow:3401 m³/h
Pressure:Δp s709 Pa
Pressure:Δp t777 Pa
Density:43862 kg/m³
Sound Pressure:80 dB(A)

3X1,5Mmâ² Orange Weight:0,326

Size : 40 mm
HGR-SQ-040-FL-R-M-S
SKU: TPGC040078
Stock: 2
Max. tear off force: 230 N
Advised working load: 77 N
With magnetic grippers, you automatically pick up flat steel products or sheets up to 10 mm thick. They are quick and easy to switch, and specially designed for transferring, placing or positioning using a robotic arm.Magnetic grippers serve as end of arm tooling for sheets. They even hold perforated sheets effortlessly.

For sheets up to 10 mm thick
Switching: pneumatic
For robot End-of-arm tooling
Lifting power: up to 45 kg
Permanent magnet

Application

End of arm tooling

Magnetic grippers are ideal when you want to pick up, place or position flat, steel products with a robot. The applications are very diverse, such as:

pick-and-place of steel parts
handling perforated sheets with a robot arm
unstacking workpieces from crates (bin picking)
positioning sheets in presses
stacking or unstacking hot baking tins

The high temperature gripper is suitable for this last example. For example, you can also use it to load and unload high-grade steel in a press; it is formed at high temperatures.


Operation

Switching and control of the magnet gripper

The magnet gripper switches pneumatically. This moves the magnetic field and switches it on and off.
Control can be with a 5/3 or possibly a 5/2 valve.
An activated magnet gripper does not release its load, even if the air pressure or power supply is lost. This makes it a safe and reliable end-of-arm solution.

Practical tips

Things to look out for when using magnetic grippers:
When working with thin sheets (≤1 mm) you must consider the ‘peeling off effect’. This reduces the maximum breakaway force. In this situation, it is better to create a construction with multiple smaller grippers (e.g. 40 x 40 mm) than one or two large grippers.
A sheet can be damaged when the gripper contacts the sheet. If this is a problem, choose the version with a protective polyurethane cap (friction type).
When working with oiled sheets or with high acceleration of the robotic arm, a sheet can shift position. This, too, can be prevented through use of the type with a polyurethane friction pad.
Sometimes the surface of a sheet is not flat, so the vacuum does not work. In this case, magnetic grippers are an ideal solution. The more contact surface area the better, but a magnet gripper always works on ferromagnetic steel. Thus on round shapes too.
The vacuum does not work when there are holes in the sheet; the magnet gripper does. In this case, choose a gripper with larger dimensions than the hole, and test the chosen solution thoroughly.
For small workpieces, Goudsmit has very small grippers in the assortment. They have a low overall height and give extra strength to hold the workpiece in place. For example, choose type HGR-RO-020.
For thin sheets (≤4 mm) and oily sheets that stick together, the robot sometimes picks up several sheets together. Sheet separators prevent this. They are available both in permanent and pneumatically switchable versions.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 70 Homologation Dimension D x H (mm) 50 x 120 Pcs x bag 50

Twin Cable / M8 STUD
The MK 450 capacitors are suitable for the heavy duty motor
applications.

CH110R General features
Wide display with graphic icons combined with the frontal keys for choosing the operation mode.
Possibility to visualize Celsius or Fahrenheit temperature values.
Maximum ambient temperature 45 °C.
Dimensions 85 x 83 x 21mm.
Electric features
24Vdc supply from the wiring center model EVWC8R
ON-OFF input through 2 wire connection to the wiring center

Polyurethane timing belt T10 width 50mm Lw 1780mm 178 teeth 50 T10/1780
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Classical shape with trapezoid teeth. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. T timing belts only run on T pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16498800

Open precision housing KG-O ISO series 3 bore 32mm for open linear bearing for shaft Ø 20mm
Material: Aluminium die-cast. Light housing for linear bearings of open design, ISO Series 3 (linear bearing has to be ordered separately). The housings can be mounted standing, upside-down or horizontally. The bearing is secured in the housing against axial and radial movement with a grease nipple.

Article ID: 64652001

Filling unit »FUTURA«, pneumatically actuated, Size 1, G 3/8, Exhaust G 1/4, Input pressure 2.5 - 16 bar, Temp. -10 °C to 50 °C
The filling unit protects devices connected downstream by ensuring a gradual build-up of pressure.
The unit consists of a 3/2-way valve including silencer and a filling valve (start-up valve).
It is connected and disconnected by means of the 3/2-way valve.
The filling time can be altered by turning the adjusting screw.

Hexagonal counter nut, G 2, AF 70, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Straight hose connection, for hose 9/12 mm, AF 24, Working pressure max. 10 bar (20 °C)/max. 1 bar (170 °C), PFA
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Bulkhead connector, Pipe exterior Ø 10 mm, PN max. 630 bar, a/f1 22, a/f2 24, a/f3 24, galvanised steel
Bulkhead connector, heavy type

Plug-in nipple push-in 6 mm, for couplings I.D. 5, nickel-plated brass, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Bracket 121, 45°, IT/ET, Rp/R 3/8, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/4, Goods class 2.5, Measurement range -1 / +5 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

1-ear hose clamp with insert ring, Stainless steel 1.4301 (W4), Clamping range 10.0 - 11.5 mm, Belt width 7.8 mm

1-ear hose clamp with insert ring, Steel bright galvanised (W1), Clamping range 8.2 - 9.5 mm, Belt width 7.8 mm
An absolutely safe all around setting is ensured by the pre-mounted insert ring. Suitably for use with soft and sensitive hose material.

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/8, Goods class 1.6, Measurement range 0 - 4 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Hose clamp, Malleable cast iron, 2-part, with loose tongues, Clamping range 28 - 34 mm, for hose I.D. 19 (3/4")

Spur gear made of polyacetal resin die-cast with hub module 0.5 21 teeth tooth width 3mm outside diameter 11.5mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28102100

Frequency:50 Hz
Speed:1400 1/min
Shaft Output:857 W
Volume Flow:3272 m³/h
Pressure:Δp s656 Pa
Pressure:Δp t719 Pa
Density:43862 kg/m³
Sound Pressure:79 dB(A)

3,3W, 230V 50Hz, 55 Led Weight:0,33

Innovative Technology
Airmar’s commitment to innovative technology has produced the M194. This broadband 200 kHz transducer has a Q of 2 and very good sensitivity. It enables users to perform accurate surveys in shallow-water with high resolution. This transducer can also be “chirped” with a long pulse over a wide-frequency band. Users with adjustable-frequency echosounders will be able to regulate the operating frequency and tailor the beamwidth to specific survey conditions.

Applications

River, harbor, and estuary survey
Shallow-water survey

Length : 150 mm
BAR-N-23-150-25-1M6-NW-B
SKU: SBAMA100010-150
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 75 Homologation Dimension D x H (mm) 50 x 120 Pcs x bag 50

Twin Cable / M8 STUD
The MK 450 capacitors are suitable for the heavy duty motor
applications.

C06 General features
Liquid expansion operation.
Direct immersion mounting of the bulb via threaded sheath Gc1/2 (included).
Sensitive element with stainless steel diaphragm
Copper bulb and capillary.
Copper sheath with Gc ½ PN10 connection
Base and cover in shock-proof selfextinguishing thermoplastic V0.
Electric features
Cod. 303298LA: cable gland G1/2 for connection output in shock-proof self-extinguishing thermoplastic material V0.
Cod. G30: copper sheath Gc 1/2 PN10 bar, length 100mm, Ø 8mm.

Polyurethane timing belt T10 width 50mm Lw 1880mm 188 teeth 50 T10/1880
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Classical shape with trapezoid teeth. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. T timing belts only run on T pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16498900

Adjustable angle fitting, Sealing cone, Nut M30x2 i., Pipe exterior Ø 22 mm, PN max. 160 bar, Stainless steel 1.4571
Version with parallel thread and soft seal made of NBR.

Safety ball valve, lockable, Venting hole M5, nickel-plated brass, Operating temp. -10 °C to 100 °C, Rp 3/8, DN 10, PN max. 14 bar
Safety ball valves, two parts, made of nickel-plated brass.
Specially designed for pneumatic applications.
The valve shuts off the supply line and bleds the application area.
Lockable hand lever in closed position ensures a high protection against manipulation.

Straight screw-in fitting, 1 5/16-12 UNF o., Pipe exterior Ø 22mm, PN max. 160 bar, A/F1 36, A/F2 41, galvanised steel, UNF threat
Male connector, male thread UNF, light type