Active charcoal filter element, for active charcoal filter »variobloc«, Size 2, G 1/2, G 3/4 and G 1

Round cylinder, ISO 6432, single-acting, Magnet, Piston Ø 16, Stroke 50, M5, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1 1/4, AF 50, Trigger pressure 7.8 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Straight screw-in fitting, M12x1,5 o., Pipe exterior Ø 6 mm, PN max. 630 bar, A/F1 17, A/F2 17, galvanised steel, soft seal
Male connector, metric thread and soft seal, heavy type

Rubber-metal buffer MGP diameter 15mm height 15mm thread M4 x 10mm stainless steel 1.4301
Material: Metal parts: Stainless steel 1.4301. Elastomer: Natural rubber, 55° Shore hardness. Rubber-Metal buffers are simple, reasonably priced standard components used for elastic mounting. When shearing load occurs their load-bearing capacity is considerably lower than with pressure load. This has to be considered when horizontal mass forces or belt traction occur. The grade of rubber used has perfect physical properties. Temperature resistant up to 80°C.
Article ID: 68929000

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 63, Stroke 80, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Check valve »multifix«, Size 1, G 3/8, Opening pressure min. 0.1 bar, Input pressure max. 16 bar, Medium / ambient temp. max. 50°C
Spring-loaded seat valves.

Service unit 3-part »G«, Metal container, Viewing tube, 5 µm, Size 600, G 1, Input pressure max. 10 bar, Control range 1.5-9 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, centrifugal separator and proportional lubricator.

Pre-assembly supports for stainless steel cutting ring fitting, M12x1, Pipe exterior Ø 8 mm, AF 12, PN max. 100 bar
When stainless steel pipes are assembled, they must always be pre-assembled in a hardened pre-assembly adapter. They must never be assembled directly in the stainless steel adapter. The cones of the pre-assembly adapters are susceptible to wear and must therefore be inspected at regular intervals to check that they are still true to gauge.

We recommend using only seamless, soft-annealed, stainless steel pipes made of
1.4571 according to DIN 2391 Part 1 or DIN 2462, tolerance class D4/T3.

Rubber-metal buffer MGS diameter 10mm height 15mm thread M4 x 10mm stainless steel 1.4301
Material: Metal parts: Stainless steel 1.4301. Elastomer: Natural rubber, hardness 55° Shore. Metal on one side only. Metal bumpers can be used to limit bearing surfaces e.g. for elastically mounted power units, and as bump stop to limit the spring travel in vehicles. They can also be used for machines that cannot be fixed to the floor or are standing on floors with an easily damaged surface, e.g. office machines. Temperature resistant up to 80°C.
Article ID: 68978300

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 63, Stroke 80, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Check valve »multifix«, Size 1, G 1/4, Opening pressure min. 0.1 bar, Input pressure max. 16 bar, Medium / ambient temp. max. 50°C
Spring-loaded seat valves.

Service unit 3-part »G«, Metal container, Viewing tube, 5 µm, Size 600, G 3/4, Input pressure max. 10 bar, Control range 1.5-9 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, centrifugal separator and proportional lubricator.

Made of plastic PA6 GF 30.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

Check valve inclined seat design stainless steel, Medium/ambient temp. max. 180 °C, G 1, PN max. 40 bar, Opening pressure 0.2 bar

Plastic container, for fine filter »Bavaria« for potable water, DVGW tested, R 3/4, R 1 and R 1 1/4

3-way brass ball valve, Pneumat. actuation drive, L-hole, Operating temperature -20 °C to 70 °C, Rp 1/2, DN 15, PN max. 40 bar
3-way cock, L-bore or T-bore, full bore.
Pneumatic actuators, double- or single acting version and integrated end-position feedback.

Bushing, Exterior hexagonal, G 1, AF 41, Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temperature 150 °C

Bush similar to DIN 1850 J (DIN 4379 C) sintered bronze borehole 18mm outer diameter 22mm length 18mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. After press-fitting them into a rigid bearing housing with a
mounting hole H7, these bearings have a bore of H7. Edges chamfered at
45°, at choice of the manufacturer. The concentricity tolerance refers
to d2. 1) no statement regarding the surface roughness according to DIN
3141 (prenorm) can be given due to the porous structure of the sintered
metal. Technical Data: Surface pressure: max. 35 N/mm², depending
on speed and diameter. Temperature range: -20°C to +120°C.Tolerances:
Inner diameter F7 / G7. Outer diameter s7. Length +/-0.1mm.

Article ID: 62334600

Compact cyl.ISO 21287, single-acting,female piston rod,retr.,magnet,PistonØ80,Stroke5,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3/2-way valve, NAMUR, NC, Anodised aluminium, Temp. max. 70 °C, Working pressure 1.5 - 10 bar, Connection G 1/4, 230 V, 50Hz
3/2 and 5/2-way spool valves, monostable, with air purging function and pneumatic spring return.
With latching manual operator and optional outgoing air restriction.

Active charcoal filter with differential pressure gauge, 0.005 mg/m³, G 1/2, Input pressure 4 - 16 bar, Temp. 5 °C to 60 °C
For adsorbing vaporous media.
A micro-filter must be connected upstream if dried air is not available.

Cross fitting, Pipe exterior Ø 15 mm, PN 315, A/F1 27, A/F2 19, galvanised steel
Cross-fitting, light type

MAEDLER deep groove ball bearing single row inner diameter 17mm outer diameter 35mm width 10mm sealed on both sides
Single row deep groove radial ball bearings Material:
Bearing steel. - Standard ball bearings in high quality. - Most common
bearing type. - Usable for high speed. - Insensitive in use and
maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or
with contacting rubber seals 2RS. Temperature range: -20°C to +90°C
(caused by type of lubrication), short-term up to 110°C. Other
versions or other bearing types on request.
Article ID: 6003-2RS-MAE

Compact cyl.ISO 21287, single-acting, male piston rod,retr.,magnet,PistonØ80,Stroke5,G1/8, Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

5/2-way valve, NAMUR, Anodised aluminium, Temp. -20 °C to 70 °C, Working pressure 1.5 - 10 bar, DN 7, Connection G 1/4, 24 V DC
3/2 and 5/2-way spool valves, monostable, with air purging function and pneumatic spring return.
With latching manual operator and optional outgoing air restriction.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 125, Stroke 150, G 1/2, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pivoting bearing, for round cylinder (not ISO 6432), Piston Ø 40, 2 threaded bolts and retaining rings
Counter-hinge model

Compact cyl.ISO 21287, single-acting,female piston rod, ext.,magnet,PistonØ80,Stroke5,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3/2-way valve, NAMUR, NC, Anodised aluminium, Operating temp. max. 70°C, Working pressure 1.5-10 bar, Connection G 1/4, 24 V DC
3/2 and 5/2-way spool valves, monostable, with air purging function and pneumatic spring return.
With latching manual operator and optional outgoing air restriction.

Suction/pressure hose, Heavy-duty design, Temp. -15°C to 60°C, Vacuum 0.9 bar, Hose Ø 46x38, PN at 20 °C max. 7 bar, Roll of 50 m
Transparent plastic hose with spiral steel wire embedded in the wall.

Suitable for process water, sludge and liquid manure under extreme conditions.
Extremely flexible and non-toxic. Acc. to 2007/19/EC.

Pipe double nipple, G 1 1/2, Length 120 mm, Working pressure max. 10 bar, Medium / ambient temperature max. 90 °C, Bright brass

Locknut DIN 981 KM7 M35x1,5 zinc plated
Material: Steel zinc-plated, Strength min. 350 N/mm2.These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65388653

Compact cyl.ISO 21287, single-acting, male piston rod ext.,magnet,PistonØ80,Stroke5,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

5/2-way valve, NAMUR, Anodised aluminium, Temp. -20 °C to 70 °C, Working pressure 1.5 - 10 bar, Connection G 1/4, 230 V, 50Hz
3/2 and 5/2-way spool valves, monostable, with air purging function and pneumatic spring return.
With latching manual operator and optional outgoing air restriction.

Active charcoal filter with differential pressure gauge, 0.005 mg/m³, G 3/8, Input pressure 4 - 16 bar, Temp. 5 °C to 60 °C
For adsorbing vaporous media.
A micro-filter must be connected upstream if dried air is not available.

Front or floor flange, ISO 15552, ISO 21287, Piston Ø 63, with 4 screws
Front or rear flange

Locknut DIN 70852 M35x1,5
Material: Steel. Hardness class 17 H according to DIN 267-24.

These nuts are used for unsafed, quickly to loosen applications, or for
a safe connection with an additional lock plate DIN 70952 (for these
lockwashers, a keyway is required on the shaft thread).

Recommend tolerance for the shaft thread: 6g DIN ISO 965.

Article ID: 65351300

Sprocket KRK with hub pitch 6mm 21 teeth material polyacetal resin
Bores ISO H8. Metal inlays at the hub with custom bore, feather keyways or threads for set screw available on request, depending on the amount and size ordered. General dimensions: B1 = 2,6 mm, c = 0,6 mm, r3 = 6 mm. Other dimensions: See the table.

Article ID: 10052100

Push-in T-fitting, L-shape, rotating, G 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

T-fitting, Pipe exterior Ø 8 mm, PN max. 100 bar, Stainless steel 1.4571

Service unit 3-part »variobloc«, Metal container incl. viewing tube and metal drip cap, Size 2, G 1, Input pressure max. 20 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator and a proportional lubricator.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Throttle check valve »Blue Series«, Straight, G 1/4 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Flange for timing belt pulley thickness 1mm Ø 54 x 50.5 x 43mm steel zinc plated
Material: Steel, zinc-plated.Flanges for timing belt pulleys, for custom-made parts or serial production. For economical reason, normally the flanges are mounted only at the smaller pulley. Often, the flanges get fixed by beading: On a turntable, with a rolling tool, hub material will get shaped over the flange. A beading material overhang of 0.5mm is recommended. Sold by piece. Other sizes are available at short delivery time.
Article ID: 16010212

3/2-way valve »FUTURA«, electr. actuated with solenoid 24 V AC, 50 Hz, Size 1, G 1/4, Exhaust G 1/4, Input pressure 2 - 10 bar
Pneumatic systems or parts of systems can be switched on and off by means of an electrical signal.
3/2-way type including silencer.
When they are switched off, the system is exhausted at the same time.

Push-in T-connector »metallica«, for hose exterior Ø 16 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 150 °C
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Back flush filter for potable water, DVGW tested, 90 µm to 110 µm, R 1 1/4, Input pressure max. 16 bar
For filtering drinking and domestic water in addition to well, process and cooling water for once-through cooling systems. These filters protect the water pipes and all water-carrying parts of the system on the downstream side against malfunctions and corrosion damage.
The filter candle must be cleaned manually at regular intervals by back-flushing (flushing out dirt particles). Integrated back-flushing element with suction elements, back-flushing lever, wing lever for back-flushing element, hose connection for flushing water.

Throttle check valve »Blue Series«, Straight, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Flange for timing belt pulley thickness 1.5mm Ø 42 x 38 x 30.5mm steel zinc plated
Material: Steel, zinc-plated.Flanges for timing belt pulleys, for custom-made parts or serial production. For economical reason, normally the flanges are mounted only at the smaller pulley. Often, the flanges get fixed by beading: On a turntable, with a rolling tool, hub material will get shaped over the flange. A beading material overhang of 0.5mm is recommended. Sold by piece. Other sizes are available at short delivery time.
Article ID: 16010302

3/2-way valve »FUTURA«, electr. actuated with solenoid 24 V AC, 50 Hz, Size 1, G 3/8, Exhaust G 1/4, Input pressure 2 - 10 bar
Pneumatic systems or parts of systems can be switched on and off by means of an electrical signal.
3/2-way type including silencer.
When they are switched off, the system is exhausted at the same time.

Nipple for couplings I.D. 7.2 - 7.8, Stainless steel 1.4305, G 1/2 IT, Operating pressure 0 - 35 bar, Temp. -15 °C to 200 °C

Throttle check valve »Blue Series«, Straight, G 1/4 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

MAEDLER deep groove ball bearing single row inner diameter 10mm outer diameter 22mm width 6mm shielded on both sides clearance C3
Single row deep groove radial ball bearingsMaterial: Bearing steel. - Standard ball bearings in high quality. - Most common bearing type. - Usable for high speed. - Insensitive in use and maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or with contacting rubber seals 2RS. Temperature range: -20°C to +90°C (caused by type of lubrication), short-term up to 110°C.Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 61900-ZZ-C3-MAE

3/2-way valve »FUTURA«, electr. actuated with solenoid 115 V AC, 50 Hz, Size 1, G 1/4, Exhaust G 1/4, Input pressure 2 - 10 bar
Pneumatic systems or parts of systems can be switched on and off by means of an electrical signal.
3/2-way type including silencer.
When they are switched off, the system is exhausted at the same time.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ25, Stroke125, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Hose reel, Mobile use, PU hose ø 12x8, Operating temperature -10 °C to 40 °C, PN max. 10 bar, G 3/8, Hose length 50 m
Specially designed for mobile applications.
This 50 m long polyurethane hose is mounted in a portable four-wheel cart made from blue anodised steel.
An automatic latching mechanism allows the hose to be engaged at any length. Enclosed spring.
Precise locking device for continuous feeding or latching mechanism. Reel guide prevents excessive wear on the hose.

Throttle check valve »Blue Series«, Straight, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Flanged bush BBP bore 25mm polyamide 6.6 outer diameter 32mm length 20mm flange diameter 40mm
Material: Thermoplastic polyamide 6.6, die cast. Color: natural.Polyamide is very well suited for the manufacture of plain bearings due to its good sliding characteristics and strong wear resistance even at dry-running conditions and because of its sufficient mechanical strength and excellent corrosion resistance. Surface pressure max.: 18 N/mm², dependant on sliding speed and bearing temperature Sliding Speed:2 m/s Lubrication: usually not required Bearing clearance: about 0.01 mm per mm shaft-Ø Bearing temperature: Should not exceed 80°C. With thin-walled parts, the frictional heat is dissipated extremely well. Coefficient of linear expansion: 8 x 10^-5 Moisture absorption max.: 7.5% Moisture absorption at 20°C and 50% rel. humidity: 2.4% Mounting hole: tolerance H7
Article ID: 62384100

3/2-way valve »FUTURA«, electr. actuated with solenoid 115 V AC, 50 Hz, Size 1, G 3/8, Exhaust G 1/4, Input pressure 2 - 10 bar
Pneumatic systems or parts of systems can be switched on and off by means of an electrical signal.
3/2-way type including silencer.
When they are switched off, the system is exhausted at the same time.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ40, Stroke55,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.