Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 32, Stroke 500, G 1/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Round cylinder, ISO 6432, double-acting, Magnet, Piston Ø 12, Stroke 50, M5, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

5/2-way valve two-sided electromagnetic, bistable, G 1/2, 24 V DC, Operating pre. 2.5-10 bar, Operating temp. -10 °C to 60 °C
This valve design, featuring the Tapered Tee Seal®, offers the ability to run without lubrication and supports almost any compressed air quality.
The valves are largely resistant to dirt and can thus also be used under extreme conditions without any problems.
Leakage is now a thing of the past and the spool no longer sticks, even after long idle periods.

Distributor pipe, 3 outlets, Input 2 x 1 with PTFE sealing ring, Output 3 x 1/2 interior thread, Brass
For assembling compressed air taps.
End fittings with 1 x male and 1 x female thread, outlets optionally with male or female thread.

Feather key DIN 6885 version A 16 x 10 x 45 mm material C45
Material: C45K.Version A.
Article ID: 61822800

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 40, Stroke 75, G 1/4, Working pressure 1.5 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Closing cap (hexagonal design), G 2 1/2, AF 85, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Service unit »ONE« without pressure switch, G 1/2, Input pressure max. 10 bar, Control range 0.5 - 8 bar, Temp. -10 °C to 50 °C
Multifunctional service unit with 6 or 7 functions in a single device:

3/2-way valve (manually operated), filter with automatic drain valve, air ports, pressure regulator, pressure gauge, soft start valve and optional pressure switch

This combination of extremely good flow rates and a wide range of functions integrated in a single, compact unit saves valuable space and is unmatched by any similar product available in the market!
Soft starting independently of the load and easy replacement of the filter cartridge under pressure are just two of the other outstanding features of this amazing device.

Distributor pipe, 3 outlets, Input 2 x 1 with PTFE sealing ring, Output 3 x 1/2 exterior thread, Brass
For assembling compressed air taps.
End fittings with 1 x male and 1 x female thread, outlets optionally with male or female thread.

MAEDLER deep groove ball bearing single row inner diameter 10mm outer diameter 19mm width 5mm sealed on both sides
Single row deep groove radial ball bearings Material:
Bearing steel. - Standard ball bearings in high quality. - Most common
bearing type. - Usable for high speed. - Insensitive in use and
maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or
with contacting rubber seals 2RS. Temperature range: -20°C to +90°C
(caused by type of lubrication), short-term up to 110°C. Other
versions or other bearing types on request.
Article ID: 61800-2RS-MAE

Wear part set, for stainless steel filter, 1.4404, G 1/2

Filter regulator »multifix-mini«, PC container and press. gauge, 5 µm, G 1/8, Input pressure max. 16 bar, Control range 0.1-3 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with secondary ventilation, in combination with a centrifugal separator. The pressure setting can be locked by pressing in the handwheel.

Filter regulator »Standard«, Metal container and pressure gauge, 40 µm, Size 4, G 1, PE max. 25 bar, 0.5-16 bar, pilot controlled
Reversible diaphragm pressure regulators, independent of inlet pressure, with selfrelieving design,
combined with a centrifugal separator.

Male hinge model with bushes, ISO 15552, ISO 21287, Ø63, with 4 screws
Male hinge model

MAEDLER deep groove ball bearing single row inner diameter 12mm outer diameter 21mm width 5mm sealed on both sides
Single row deep groove radial ball bearings Material:
Bearing steel. - Standard ball bearings in high quality. - Most common
bearing type. - Usable for high speed. - Insensitive in use and
maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or
with contacting rubber seals 2RS. Temperature range: -20°C to +90°C
(caused by type of lubrication), short-term up to 110°C. Other
versions or other bearing types on request.
Article ID: 61801-2RS-MAE

2/2-way solenoid valve brass, NC, directly operated, 230 V, 50 - 60 Hz, Medium temperature -15 °C to 100 °C, G 1/4, PN 0 - 11 bar
Standard series, proven over many years, available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Filter regulator »multifix-mini«, PC container and press. gauge, 5 µm, G 1/4, Input pressure max. 16 bar, Control range 0.5-10 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with secondary ventilation, in combination with a centrifugal separator. The pressure setting can be locked by pressing in the handwheel.

Service unit 2-part »Standard« with polycarbonate container, Size 4, G 3/4, PE max. 16 bar, Control range 0.5 - 10 bar, pilot con.
Two-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure,
with self-relieving design, combined with a centrifugal separator and a proportional lubricator.

Straight push-in connector with plug nipple 6 mm, reducing, for hose exterior Ø 4 mm, Working pressure max 15 bar, Stainless steel
For use with aggressive media and in areas susceptible to corrosive outside
influences, in the food processing industry and in hygienic and sanitary applications.

MAEDLER deep groove ball bearing single row inner diameter 15mm outer diameter 24mm width 5mm shielded on both sides
Single row deep groove radial ball bearings Material:
Bearing steel. - Standard ball bearings in high quality. - Most common
bearing type. - Usable for high speed. - Insensitive in use and
maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or
with contacting rubber seals 2RS. Temperature range: -20°C to +90°C
(caused by type of lubrication), short-term up to 110°C. Other
versions or other bearing types on request.
Article ID: 61802-ZZ-MAE

Storz reducer, Aluminium, Storz size 75-B, Tappet distance 89 mm, Flange DN 80, Operating pressure max. 16 bar
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Filter regulator »multifix-mini«, PC container and press. gauge, 5 µm, G 1/4, Input pressure max. 16 bar, Control range 0.1-3 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with secondary ventilation, in combination with a centrifugal separator. The pressure setting can be locked by pressing in the handwheel.

Standard cylinder, ISO 15552, double-acting, Piston Ø 100, Stroke 320, G 1/2, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches can be mounted in two T-slots on the same side as the compressed air supply.
The version with a 125 mm bore is provided with fixing accessories on three sides as standard.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Supply strip for the way valves, Supply strip with 4 valve positions, for valves connection G 1/8
Quick and easy assembly system for side-by-side mounting of the above control valve types. Requires one set of mounting brackets and a feed block.

Rubber-metal buffer MGH stainless steel diameter 45mm height 20mm bore 10,5mm (for screw M10)
Material: Elastomer: Rubber NBR, black, hardness 55º Shore A. Metal part: Stainless steel 1.4301.Hollow design. One side metal, with mounting bore for allen screw DIN 912.Due to the hollow design, these elements are particularly suitable as end stops. Also usable as elastic machine feet.The grade of rubber has perfect physical properties.Temperature resistant up to +100ºC (for short time +120°C).Other sizes, Shore hardnesses or elastomer types on request.* Permissible Pressure Load.
Article ID: 68921451

Timing belt pulley XL material aluminium 12 teeth for belt width 025=6,35mm
Material: Aluminium similar EN AW2017A.Flanges zinc-plated steel. Pre-bored (up to a Teeth Number of 24 only centre hole).Profile XL = 1/5" = 5.08 mm. Belt width 025 = 6.35 mm.
Article ID: 18011200

Standard cylinder, ISO 15552, double-acting, Piston Ø 40, Stroke 160, G 1/4, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches can be mounted in two T-slots on the same side as the compressed air supply.
The version with a 125 mm bore is provided with fixing accessories on three sides as standard.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Filter regulator »multifix-mini«, PC container and press. gauge, 5 µm, G 1/8, Input pressure max. 16 bar, Control range 0.5-10 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with secondary ventilation, in combination with a centrifugal separator. The pressure setting can be locked by pressing in the handwheel.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 100, Stroke 800, G 1/2, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled screw-in fitting, R 1/4 o., for hose 6/4 mm, AF 12/10, Pressure max. 25 bar, Temp. -40 °C to 200 °C Stainless steel 1.4404
Supplied without seals. For use with corrosive media and at high temperatures.

Screw fitting series made of stainless steel for all applications where compliance with strict tightness, pressure and temperature requirements is essential.
The parts are manufactured without rubber seals, in other words they are ideal for very high temperatures or for use with corrosive liquids, e.g. in cases when FPM is no longer suitable.

Neoprene timing belt 140 MXL 175 teeth Lw 355.60mm belt width 025
Material: Neoprene with glas-fibre tensile member. Teeth surface fabric-coated. Timing belt with inch dimensions, classical shape with trapezoid teeth. Profile MXL = 0,08" = 2.032 mm. Belt width 025 = 6.35mm. Temperature range -20º to +100ºC.
Article ID: 18186500

3/2-way valve »FUTURA«, pneumatically actuated, Size 2, G 3/8, Exhaust G 1/2, Input pressure max. 16 bar, Temp. -10 °C to 50 °C
Pneumatic systems or parts of systems can be switched on and off by means of an pneumatic signal.
3/2-way type including silencer.
When they are switched off, the system is exhausted at the same time.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 8x6 mm, PN at 23 °C max. 10 bar, silver, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Standard cylinder »SE« ISO 15552, double-acting, Piston Ø 100, Stroke 500, G 1/2, Working pressure 1 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on three sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Mini bleeder valve, Stainless steel, not component checked, Operating temp. -20 °C to 180 °C, G 1/8, Trigger pressure 3 - 7 bar
Manual adjustment of the blow-off pressure (lock nut).
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.

single direction thrust ball bearing 51202 inner Ø 15mm outer Ø 32mm height 12mm
Material: Bearing steel.Thrust Ball Bearings for single direction in brand quality from MAEDLER®.For axial load (no radial load permitted).Usable for high speed.These bearings exist from lose parts: Shaft ring (with ground bore), housing ring (with ground outer diameter and bigger bore) and ball cage with balls. The rings must not be confused with each other.Temperature range: -30°C to +125°C. Other versions or sizes on request.

Article ID: 51202-MAE

3/2-way valve »FUTURA«, pneumatically actuated, Size 2, G 1/2, Exhaust G 1/2, Input pressure max. 16 bar, Temp. -10 °C to 50 °C
Pneumatic systems or parts of systems can be switched on and off by means of an pneumatic signal.
3/2-way type including silencer.
When they are switched off, the system is exhausted at the same time.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 8x6 mm, PN at 23 °C max. 10 bar, red, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Stainless steel filter, 1.4401, 25 µm, Size 1, G 1/4, Input pressure max. 30 bar, Medium temperature max. 80 °C
Stainless steel filters for use in the chemical industry, mining, plant construction and
special machinery industries, pneumatics, etc.

Mini bleeder valve, Stainless steel, not component checked, Operating temp. -20 °C to 180 °C, G 1/4, Trigger pressure 10 - 18 bar
Manual adjustment of the blow-off pressure (lock nut).
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.

Spare part set of elastomeres for coupling MAEPEX size 58 NBR 80 Shore A black
Material: NBR, hardness 80ºA Shore, black.Sold by set of 4 to 8 pieces, depending on the coupling size.Other hardnesses in request (soft 65° or hard 90° A Shore).Temperature range: -30ºC to +80ºC.
Article ID: 60560101

Blocking valve pneumat. actuated, double-acting, NC, nickel-plated brass, Temp. -20°C to 80°C, Control pressure 3-8 bar, Rp 3/8
2/2-way check valves, specially designed for automated industrial plant engineering.
A low-price, compact, space-saving and reliable alternative to ball valves with a pneumatic rotary actuator.
These valves have a full bore and - owing to the optimised design - only minimal flow losses.
They are controlled by means of filtered compressed air.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 8x6 mm, PN at 23 °C max. 10 bar, yellow, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Stainless steel filter, 1.4401, 25 µm, Size 1, G 3/8, Input pressure max. 30 bar, Medium temperature max. 80 °C
Stainless steel filters for use in the chemical industry, mining, plant construction and
special machinery industries, pneumatics, etc.

Mini bleeder valve, Stainless steel, not component checked, Operating temp. -20 °C to 180 °C, G 1/8, Trigger pressure 1 - 4 bar
Manual adjustment of the blow-off pressure (lock nut).
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.

Spare part set of elastomeres for coupling MAEPEX size 68 NBR 80 Shore A black
Material: NBR, hardness 80ºA Shore, black.Sold by set of 4 to 8 pieces, depending on the coupling size.Other hardnesses in request (soft 65° or hard 90° A Shore).Temperature range: -30ºC to +80ºC.
Article ID: 60560102

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 32, Stroke 150, G 1/8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 8x6 mm, PN at 23 °C max. 10 bar, green, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

2-way brass ball valve, Pneumat. actuation drive spring switching, Operating temp. max. 70 °C, Rp 1/2, DN 15, PN max. 40 bar
2-way cock, full bore.
Pneumatic actuators, double- or single acting version and integrated end-position feedback.

Mini bleeder valve, Stainless steel, not component checked, Operating temp. -20 °C to 180 °C, G 1/8, Trigger pressure 6 - 12 bar
Manual adjustment of the blow-off pressure (lock nut).
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.

Spare part set of elastomeres for coupling MAEPEX size 80 NBR 80 Shore A black
Material: NBR, hardness 80ºA Shore, black.Sold by set of 4 to 8 pieces, depending on the coupling size.Other hardnesses in request (soft 65° or hard 90° A Shore).Temperature range: -30ºC to +80ºC.
Article ID: 60560103

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 63, Stroke 30, G 1/4, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Made of plastic PA6 GF 30.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

2-way brass ball valve, Pneumat. actuation drive spring opening, Operating temp. max. 70 °C, Rp 1/2, DN 15, PN max. 40 bar
2-way cock, full bore.
Pneumatic actuators, double- or single acting version and integrated end-position feedback.

Mini bleeder valve, Stainless steel, not component checked, Operating temp. -20 °C to 180 °C, G 1/8, Trigger pressure 10 - 18 bar
Manual adjustment of the blow-off pressure (lock nut).
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.

Protection cap for pillow bearings TUCP TUCF TUCFL 207 open design bore 35mm thermoplast black
Material: Thermoplast PBT, black.Open Design, with sealing, for shaft side or closed design.The caps fit only on the one bearing side with the setscrews and can get clipped on by hand by the customer.
Article ID: 62555235

Short stroke cylinder, single-acting, Magnet, Piston Ø 63, Stroke 25, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

GEKA threaded piece, rigid, Safety design, bright brass, G 1 o., Operating pressure max. 40 bar, Med./ambient temp. -10°C to 90°C
Claw couplings (claw distance: 40 mm) made of brass for water, industrial, mortar, suction and discharge hoses. Suitable for a wide range of applications, e.g. industrial plant engineering, civil and structural engineering, environmental engineering, manual trades, domestic water engineering, horticulture and landscaping, agriculture and forestry, etc.
Available in a rigid or 360° swivelling version. The two systems can also be easily coupled to one another!

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 80, Stroke 900, G 3/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Mini bleeder valve, Stainless steel, not component checked, Operating temp. -20 °C to 180 °C, G 1/8, Trigger pressure 16 - 32 bar
Manual adjustment of the blow-off pressure (lock nut).
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.