Closing cap (hexagonal design), G 3/8, AF 20, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Replacement seal for flange pressure controller, Flange connection 300 bar, all types of gas, O-Ring 7.65 x 1.78 mm

Screw-in hose connector, G 1 o., for hose I.D. 32, nickel-plated brass
Suitable for air, water, oil, steam, etc.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Straight hose connection supports, for hose I.D. 4 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Captive nipple I.D. 5, Bright brass, G 1/4 ET, blue, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C

The controller ST64-31.10 was developed for simple thermostatic controls. The round housing allows applications at locations in which formerly only mechanical controls were in use. The unit is supplied with a tension of 230V AC and is pre-set for Pt100 sensor. The installed relay has a maximum electric Ohm load of 16A. Inductive loads can be switched up to 2,2A. 900197.008

Retaining ring DIN 471 6mm
Material: Feather steel, phosphated, oiled. External rings for
axial fixing a machine part on a shaft.

Article ID: 61740600

Pressure Ranges -1 to 210 bar
Accuracy +/- 2.5%
50mm Gauge

Rotating joint with aluminium- or brassdesign for water

Frequency:50 Hz
Speed:2750 1/min
Shaft Output:31 W
Volume Flow:200 m³/h
Pressure:192 Pa
Pressure:247 Pa
Density:1.2 kg/m³
Sound Pressure:64 dB(A)
ErP Compliance:

For Lv200 And Gv200 5 Pc Weight:0,01

1 kW

NOTE: AIRMAR NO LONGER MANUFACTURES THIS PRODUCT

The performance of Airmar’s "1 kW 260 family" of transducers has made them legendary. The combination of power and sensitivity has made this the high performance transducer of choice for use with conventional fishfinders. Operating at 50 kHz and 200 kHz, the narrow 6° beam at 200 kHz provides excellent target resolution and crisp images of fish holding tight to wrecks and reefs. The 50 kHz provides excellent deep water detection and the wide 19° beam provides broad coverage under the boat.

The CM260 is designed for tank mounting in commercial fishing vessels. Its versatile design also allows it to be flush mounted in the keel.

Neodymium (NdFeB) 100 N
PM-RTE-N-RB-D43-6-M6-21
SKU: GM17518
Stock: 47
Size: Ø43 mm
Height (L): 12 mm
Shear force: 30 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 2,5 Homologation VDE | IMQ Dimension D x H (mm) 25 x 57

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

25 – 27 series ring and control knob General features
Ring and control knob for C02 thermostats series

HEXAGONAL NIPPLE - STAINLESS STEEL 316

Information

Hexagonal nipple - Stainless steel 316> DiamA " very available: from DN6 to DN50- Gas thread> Nominal pressure of the hexagonal nipple: - 20 bar A 20AdegC- 16 bar A 100AdegC> Standard ISO 228-1

Slip shaft with joints PW both sides bore 14H7 telescoped length 210mm max. length 280mm steel outer diameter 29mm
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Spline shaft C40. Max. Operating Angle per Joint 45°. Other lengths on request. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63182900

Precision shaft steel with shaft support Ø 20h6 x 600mm long
Material: Steel 1.1213 (Cf53), hardened and ground, hardness 62±2 HRC, diameter tolerance ISO h6. Material support: Extruded aluminium. Length: Either 600 mm or 1200 mm. Ready-to-use, mounted, supported linear shafts to be used with open linear bearings or open linear bearing units. The shafts are supported over their entire length. The shaft supports have mounting holes for mounting them on a base plate. Unit can be shortened by the customer using an angle grinder. Longer versions on request.

Article ID: 64742003

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

internal term: P-ND One way : yes 2 way with a standing inner tube: no
190 C 17,0 bar water
Universal use – cooling, heating, clamping
With bellows sealing
Cartridge fast change CD-cartridge-design
Sealingmaterial ceramics/graphite
Ballbearings (can be relubricated)
No elastomers – therefore no temperature and chemical resistance problems
No loose parts, f.e. springs
Robust and less influence of dirty media
Self supporting – no additional support necessary
Available in stainless steel

internal term: 3-4 inch, 90 C 10,0 bar water One way: no 2 way with a standing inner tube :yes 2 way with a standing inner tube: no

3-4 inch, 130 C internal term: SRO One way: no 2 way with a standing inner tube: Yes 2 way with rotating inner tube: No

Pressure gauge, robust design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 250 bar, Ø 160
Robust bourdon-tube pressure gauge.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Cross-piece 180, 4 x IT, Rp 1 1/2, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Pushbutton safety coupling I.D. 5.5, ARO 210, rotating, Alu, Sleeve I.D. 6, Operating pressure max. 12 bar, Temp. -20°C to 70°C
High-quality, robust and durable, one-hand quick disconnect safety couplings.
When it is pressed for the first time, air is relieved from the coupling but the plug in the coupling remains locked. The plug is only disconnected when the pushbutton is pressed for the second time.
The dreaded "whiplash effect" is avoided and the risk of injury to the operator virtually eliminated.

The safety version conforms to ISO-Standard DIN EN ISO 4414.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive.

Straight hose connection, for hose 4/6 mm, AF 14, Working pressure max. 10 bar (20 °C)/max. 1 bar (170 °C), PFA
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Plug nipple pipe DN 6, Brass 2.0401, Pipe exterior Ø 10 mm, AF 11, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Coupling nut with kink protection spring, for hose 12/10 mm, AF 18, Working pressure max. 18 bar, nickel-plated brass

Straight Check valve »Blue Series«, Hose to thread, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
The non-return function of these push-in fittings prevents the air from flowing back, the unidirectional design means air flow is only possible in one direction.
These valves are available with air flow from the port to the tube or from the tube to the port.

Locking screw, Hexagonal socket, without flange, G 1/8, AF 5, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Elbow 41, 45°, Rp 1 IT, Rp 1 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Screw-in hose connector, R 3/8 o., for hose I.D. 8, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Push-in Y-connector »Blue Series« reducing, for hose exterior Ø 1x16/2x12 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Extension piece short »value line«, G 1/8 o., G 1/8 i., AF 14, Operating pressure max. 60 bar, Operating temperature max. 150 °C
For air, water, steam, oil, etc.

Mounting bracket incl. 2 screws, galvanised steel, for »FUTURA«, Size 1, G 1/4 and G 3/8

T-distributor, G 1/4, AF 22, Brass

Angled screw-in supports, R 3/4 o., for hose I.D. 19 mm, AF 27, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Double threaded nipple, M5 o., M5 o., AF 8, nickel-plated brass
Previous design. Can be delivered as long as in stock.
After sale the delivery is made in new optimised geometry.

Suitable for air, water, oil, steam, etc.

Angled screw-in fitting, ET conical, R 1/8, for hose 10/8 mm, AF 11, Working pressure max. 18 bar, nickel-plated brass

Push-in T-fitting »metallica«, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Flat sealing ring made of PTFE, G 1/4, EN 837

Intermediate hinge, ISO 6432, Piston Ø 12-16, galvanised steel, 1 piece
Intermediate hinge

Straight push-in connector, Plug nipple »Blue Series«, red., hose exterior Ø 10, plug nipple 12, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Clamping ring, for hose 4/6 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PP
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Captive nipple I.D. 5, Bright brass, G 1/8 IT, blue, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C

The controller ST64-31.10 was developed for simple thermostatic controls. The round housing allows applications at locations in which formerly only mechanical controls were in use. The unit is supplied with a tension of 12-24V AC or 16-36V DC and is pre-set for PTC sensor. The installed relay has a maximum electric Ohm load of 5A. Inductive loads can be switched up to 2,2A. 900197.018

Retaining ring DIN 471 8mm
Material: Feather steel, phosphated, oiled. External rings for
axial fixing a machine part on a shaft.

Article ID: 61740800

Splined hub DIN 14 KN 46X54 length 90mm diameter 80mm red brass Rg7
Material: Red Brass (CuSn7Zn4Pb7-C).A/d up to size 18 x 22 = 0,15 mm, above 0,2 mm
Article ID: 64836400

Pressure Ranges 0 to 20 bar
Accuracy +/- 2.5%
50mm Gauge

Rotating joint with aluminium- or brassdesign for water
internal term: PRO One way: yes 2 way with a standing inner tube: No 2 way with rotating inner tube: No

Frequency:50 Hz
Speed:2785 1/min
Shaft Output:32 W
Volume Flow:203 m³/h
Pressure:196 Pa
Pressure:254 Pa
Density:1.2 kg/m³
Sound Pressure:64 dB(A)

For Ls 10 And Lg 10, Lv 250 And Gv 250 Ve=5 Pc. Weight:0,01

1 kW

Operating at 50 and 200 kHz, the TM258 features an elliptical beam from four ceramic elements. The beamwidth is narrow on both frequencies for excellent resolution in both shallow and deep water. The TM258 comes with a rugged stainless steel mounting bracket that is easy to install and has a streamlined shape. The combination of power and sensitivity has made this the high-performing transducer of choice for use with conventional fishfinders.

Neodymium (NdFeB) 500 N
PM-TI-N-SG-D40x8xM5
SKU: GM17439
Stock: 298
Diameter (D): 40 mm
Height: 8 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a cylinder hole for easy mounting. These pot magnets are screwable at a high torque while the magnet remains unloaded. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with cylinder hole are available in various sizes and grades such as neodymium and ferrite.

Deliverable from stock
Available in various qualities
Available with extra strong magnet
High torque screwable

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion. The cylinder hole makes the magnet system screwable with a high torque.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Screwable at a high torque

These pot magnets with cylinder hole are suitable for extra tightening. There is no force on the pot magnet itself. This is not a part of the screw connection. Mounting is easy with a cylinder head bolt.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 3 Homologation VDE | IMQ Dimension D x H (mm) 25 x 57

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

25 – 27 series ring and control knob General features
Ring and control knob for C02 thermostats series

WELDING NIPPLE LENGTH 50 MM - STAINLESS STEEL 316L

Information

MAC / le - 316L stainless steel> DiamA " very available: from DN8 to DN50 - Gas Thread> Characteristics (c) ristics of the mAC / le - 316L stainless steel: Tube RoulA (c) / SoudA (c) - Schedule 20S> Nominal pressure of the mAC / le nozzle: PN50> ISO standard 7/1

Slip shaft with joints PW bore 14H7 with keyway DIN 6885-1 tolerance JS9 on both sides min. length 210mm max. length 280mm steel
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Spline shaft C40. Max. Operating Angle per Joint 45°. Other lengths on request. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63182900N