Pressure regulator »multifix«, incl. pressure gauge, Size 3, G 3/4, Input pressure max. 16 bar, Control range 0.2 - 6 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the button down.

Pressure regulator »lineonline«, Thread (inlet) - hose (outlet), G 1/4, for hose Ø 8 mm, Operating pressure 2 - 10 bar
Particularly suitable for installation between the valve and cylinder and as a pressure regulator in secondary branches of the pneumatic system. The regulator is fitted with a pressure limiting valve for overpressure exhaust.

Straight push-in fitting »Blue Series« mini, M5 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Reducing sleeve 246, IT/ET, Rp 1 1/4, R 1, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Standard pressure gauge, Double scale, Connection, rear, centr., G 1/4, Goods class 1.6, Measurement range 0-16 bar/230 psi, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-in hose connector »value line«, R 1/4, for hose I.D. 10, Operating pressure max. 60 bar, Operating temperature max. 150 °C
For air, water, steam, oil, etc.

Splined hub with flange DIN 14 KN 23X28 length 55mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64899503

Feather key DIN 6885 version A 6 x 6 x 18 mm material C45
Material: C45K.Version A.
Article ID: 61812100

Frequency:50 Hz
Speed:2930 1/min
Shaft Output:343 W
Volume Flow:437 m³/h
Pressure:Δp s1399 Pa
Pressure:Δp t1699 Pa
Density:43862 kg/m³
Sound Pressure:79 dB(A)

Colour: Ral 7035 Light Grey Weight:1,8

Length : 250 mm
BAR-ES-23-250-25-2M8-NW-B
SKU: SBAQA100040-250
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M8 (2x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 15 Homologation VDE | IMQ Dimension D x H (mm) 40 x 70 Pcs x bag 50

Bolt set with retainer KL ø5mm; for clevises size 5x10 and 5x20
Material: Steel zinc-plated. Bolt with KL retainer. The set exists from one bolt and a fitting KL retainer. It can be used with all clevises according to DIN 71752 or other clevises with dimensions like DIN. KL retainer can get mounted and dismounted very easily. They are intended for connections which must be disassembled more often. It is necessary to ensure that there is no unwanted strong contact to the retainer, because it is easily to remove.
Article ID: 63780300

Bevel gear made of stainless steel 1.4305 module 4 15 teeth i=2:1
Material: Stainless steel 1.4305. Tooth quality 8 modelled on DIN 3967 (from module 2). Crowned, milled teeth. Shaft angle 90º. The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module and ratio. At ratio 1:1, you need two pieces of the same number of teeth. At ratio uneven 1:1, you need two pieces with a different number of teeth of the same ratio.
Article ID: 36199856

Steel bellow coupling MCK short version MDmax 18Nm both sides bore 24mm overall length 63mm hub diameter 45mm
Material: Aluminium clamp hubs, stainless steel bellow. Zero backlash, with high torsional stiffness. For machine tools, packing machines, textile machines, linear drives etc.. With clamps, ready-to-install for rapid mounting. Temperature range of all types -30°C to +120°C. 1) Standard bores. 2) Different bores (even one-sided) up to max bore as well feather keyways, available against surcharge.Please regard the operating factors. See PDF-catalog page.
Article ID: 60154624

Articulated male hinge model, ISO 15552, Ø200, with 4 screws

Bulkhead elbow connector, Pipe exterior Ø 20 mm, PN max. 400 bar, a/f1 36, a/f2 41, a/f3 27, galvanised steel
Bulkhead elbow connector, heavy type

Pressure regulator »multifix«, incl. pressure gauge, Size 3, G 3/4, Input pressure max. 16 bar, Control range 0.5 - 10 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the button down.

Pressure regulator »lineonline«, thread (outlet) - hose (inlet), G 1/4, for hose Ø 8 mm, Operating pressure 2 - 10 bar
Particularly suitable for installation between the valve and cylinder and as a pressure regulator in secondary branches of the pneumatic system. The regulator is fitted with a pressure limiting valve for overpressure exhaust.

Straight push-in fitting »Blue Series« mini, M5 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Reducing sleeve 246, IT/ET, Rp 1 1/4, R 3/4, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight Push-in fitting »Blue Series«, Self-locking, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Screw-in hose connector »value line«, R 1/4, for hose I.D. 12, Operating pressure max. 60 bar, Operating temperature max. 150 °C
For air, water, steam, oil, etc.

Frequency:50 Hz
Speed:2820 1/min
Shaft Output:447 W
Volume Flow:415 m³/h
Pressure:Δp s2084 Pa
Pressure:Δp t2325 Pa
Density:43862 kg/m³
Sound Pressure:80 dB(A)

Colour: Ral 7035 Light Grey Weight:1,8

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 16 Homologation VDE | IMQ Dimension D x H (mm) 40 x 70 Pcs x bag 50

ECCF15GSA – ECCF20GSA General features
Autonomous hydraulic unit: super dry magnetic transmission.
Long-term performances: pressure-tight casing, sealed with O-ring.
Mechanical register with REED contact.
REED cable with 2 mt length, not extendable.
10 litres/pulse.
R(Q3/Q1)= 25.
Standard reading capacity: 9999.999 m.
Minimum displayed value: 0.001 m³.

Bolt set with retainer SL ø5mm; for clevises size 5x10 and 5x20
Material: Steel zinc-plated. Bolt with SL retainer. The set exists from one bolt and a fitting SL retainer. It can be used with all clevises according to DIN 71752 or other clevises with dimensions like DIN. SL retainers are not so easy and quick to mount and to dismount like KL retainers, but the connection is much better secured against unwanted loosening.
Article ID: 63790300

Tandem linear bearing unit KGT-3 ISO series 3 Economy-Line with linear ball bearings with angular compensation with seals for shaft Ø 16mm
Material: Material: Housing made from extruded aluminium with two closed linear bearings of the ISO Series 3 from reliable brand in good quality at low price. Self-aligning capability that accommodates tilting. All bearings are lubricated ready-to-install. Recommended shaft tolerance h6.
Article ID: 64681602

Steel bellow coupling MCK short version MDmax 18Nm both sides bore 25mm overall length 63mm hub diameter 45mm
Material: Aluminium clamp hubs, stainless steel bellow. Zero backlash, with high torsional stiffness. For machine tools, packing machines, textile machines, linear drives etc.. With clamps, ready-to-install for rapid mounting. Temperature range of all types -30°C to +120°C. 1) Standard bores. 2) Different bores (even one-sided) up to max bore as well feather keyways, available against surcharge.Please regard the operating factors. See PDF-catalog page.
Article ID: 60154625

Push-in X-connector, for hose exterior Ø 12 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Adjustable male connector, with cone seal, M20x1.5 o., Pipe exterior Ø 14, PN 630, a/f1 27, a/f2 27, galvanised steel

Pressure regulator »multifix«, incl. pressure gauge, Size 3, G 3/4, Input pressure max. 16 bar, Control range 0.5 - 16 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the button down.

Electrical connection cable with 90° angle socket and 5 m cable, 5-wire, for service unit »ONE«

Straight push-in fitting »Blue Series« mini, M6 o., for hose exterior Ø 3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

3/3 Tube fitting, G 3/4 x 13 mm, swivel nut, taper seat, CH type, Brass with a bare metal surface

Elbow 1a, 90°, short, Rp 1 1/2 IT, R 1 1/2 ET black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Worm thread hose clamp, Chrome steel 1.4016 (W2), according to DIN 3017, Clamping range 40.0 - 60.0 mm, Belt width 9.0 mm
Worm drive type.

For all standard applications where high clamping forces are normally distributed.

Hexagon-head screw a/f 7, with integrated cross-tip, bright galvanised steel, passivated blue.

Round gear rack made of steel C45 module 3 diameter 30mm h6 length 2000mm
Material:
Up to length 1,500mm: Steel St50K.
Length 2000mm = Steel C45k.
Outside diameter = h6 ground.

Straight teeth, milled.
Pressure angle 20°. Tooth quality 8d25 modelled on DIN 3967.

The teeth on the gear racks are manufactured using an overhead milling cutter.
This leads to negative tolerances. Dimensions ha and h0:
up to Module 2: -0,2 mm.
Module 2,5 - 4: -0,3 mm.
Module 5 - 6: -0,4 mm.




Article ID: 24363400

Frequency:50 Hz
Speed:2825 1/min
Shaft Output:406 W
Volume Flow:407 m³/h
Pressure:Δp s1887 Pa
Pressure:Δp t2122 Pa
Density:43862 kg/m³
Sound Pressure:82 dB(A

2 Fans, Single Row, 1 Height Unit Weight:1,8

Length : 400 mm
SVM-F-154x47-0400-B-F0E
SKU: SVMF020400
Stock *: 0
Advised max. installation height: 60-75 mm
Height: 47 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 18 Homologation VDE | IMQ Dimension D x H (mm) 40 x 70 Pcs x bag 50

OMC4 General features
Module dimensions: 46x46x37 mm
Case dimensions: 95x60x40 mm
Clamp section: 2.5 mm²
Electric features
Power supply: 230Vac +/- 10% 50Hz
Output maximum current: 10A j 1 4A cosj 0.4
Contact work time: 2.5 min. where foreseen
Contact voltage: 5/6/7 230Vac 50Hz

Ball knob DIN 319 Technopolymer PA6GV type E ø20 M6
Material PA: Thermoplast (Polyamide PA6 GV), glass-fibre reinforced, impact resistant, black matt.Version E = With threaded bush of zinc-plated steel.             Size 20/M6, 25/M8 and 32/M10 is not part of the DIN 319.

Article ID: 66482006

Precision spur gear made of steel 16MnCr5 module 2 30 teeth bore 20mm hardened and ground outside diameter 64mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2.
Teeth, bores and faces ground.

Tooth quality 7 e25.
Pressure angle 20°.

Feather Keyways in accordance with DIN 6885/1, tolerance P9.
Position of keyway to tooth is not defined.

Article ID: 24183020

Steel bellow coupling MCL long version MDmax 18Nm both sides bore 10mm overall length 71mm hub diameter 45mm
Material: Aluminium clamp hubs, stainless steel bellow. Zero backlash, with high torsional stiffness. For machine tools, packing machines, textile machines, linear drives etc.. With clamps, ready-to-install for rapid mounting. Temperature range of all types -30°C to +120°C. 1) Standard bores. 2) Different bores (even one-sided) up to max bore as well feather keyways, available against surcharge.Please regard the operating factors. See PDF-catalog page.
Article ID: 60164610

5/2-way valve, Pneumatic, monostable, Connection G 1/2, DN 15, Operating pre. 2.5 to 10 bar, Operating temp. -10°C to 60°C

Male elbow, NPT 3/4 o., Pipe exterior Ø 22 mm, PN max. 160 bar, a/f1 36, a/f2 27, galvanised steel
Male elbow, NPT thread, light type

Pressure regulator »multifix«, incl. pressure gauge, Size 3, G 1/2, Input pressure max. 16 bar, Control range 0.2 - 6 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the button down.

Angled screw-in fitting G 1/8 o., for hose 6/8 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (170 °C), PFA
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Straight push-in fitting »Blue Series« mini, M6 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Male branch elbow »universal short«, rotating, 1/4, hose-Ø 8, taper seat, Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Straight connector POM, for hose exterior Ø 22 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Reducing piece 241, R 1/2 ET, Rp 1/4 IT black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

High performance V-belt XPZ EPDM datum length 1237 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091237

High performance V-belt XPZ EPDM datum length 1030 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091030

Frequency:50 Hz
Speed:2930 1/min
Shaft Output:449 W
Volume Flow:447 m³/h
Pressure:Δp s2127 Pa
Pressure:Δp t2406 Pa
Density:43862 kg/m³
Sound Pressure:76 dB(A)

24V Dc, 12W, Ip67, Glass Tube, Diffus, L=582Mm Weight:1,82

Cable set 10 m
CABLE SET DEMAG. 75Amp L=10m
SKU: E0065613
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.