Pse 30 24V Dc Weight:1,48

Length : 600 mm
SVM-F-114x47-0600-B-F0E
SKU: SVMF010600
Stock *: 0
Advised max. installation height: 50-65 mm
Height: 47 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 8 Homologation VDE | IMQ Dimension D x H (mm) 30 x 70 Pcs x bag 50

C50 General features
3-position switch to select the temperature:– ECONOMY– OFF (turn-off with frost protection)– COMFORT
– ECONOMY
– OFF (turn-off with frost protection)
– COMFORT
Large display with continuous indication of the read ambient temperature (thermometer) and the symbol of the current mode COMFORT, ECONOMY or OFF.
Fixed antifreeze temperature 8°C.
Double insulation.
The batteries are replaced through thermostat’s front.
Batteries operation life of approximately 4 years.
Flashing display in case of insufficient batteries charge.
Maintenance of all data during batteries replacement.
Unit weight 0.13 Kg.
Electric features
– ECONOMY
– OFF (turn-off with frost protection)
– COMFORT

Cylindrical bush slotted version 10 x 12 x 10 mm
Main characteristics Self lubricating and maintenance free, ready to install. Perfectly suited for lower sliding speeds. Low wear, low friction coefficient, no 'stick slip'. Perfectly suited for circular, swivelling and partly for axial movement. Can be used at extremely high bearing loads. No moisture absorption. High corrosion Construction Tin-plated steel back (incl. edges). Multi-porous bronze layer, sliding surface PTFE-lead-compound. Technical data Stat. surface pressure: max. 250 N/mm² Dyn. bearing load: max. 56 N/mm² Friction coefficient: 0.03 - 0.20 Sliding speed: max. 2 m/s Temperature range: -195°C to 280°C Therm. conductivity: 40 W/K*m Recommended mounting tolerances Housing bore H7, shaft tolerance up to 55 Ø f7 above 55 Ø h8

Article ID: 62401010

Neoprene timing belt 1250 H 250 teeth belt width 150=38.1mm
Material: Neoprene with glas-fibre tensile member. Teeth surface fabric-coated. Timing belt with inch dimensions, classical shape with trapezoid teeth. Profile H = 1/2" = 12.7 mm. Belt width 150 = 38.1 mm. Temperature range -20º to +100ºC.
Article ID: 18476900

2/2-way solenoid valve brass, NC, force pilot operated, 24V DC, 14W, Medium temp. -10°C to 90°C, NBR+PA, G 1, PN 0 - 6bar
Economy series available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Ball valve, Manual lever, Basic design, IT/IT, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 3/4, DN 20, PN max. 40 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.

Counter bearing, ISO 15552, for compact cylinder, Standard cylinder, Piston Ø 100, with 4 screws
Counter-hinge model

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ20, Stroke45, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight push-in fitting »Blue Series« mini, round, M5, for hose exterior Ø 3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Angled screw-in fitting, R 1/4 o., Pipe exterior Ø 6 mm, PN max. 315 bar, AF1 14, AF2 12, galvanised steel
Male elbow, conical male thread acc. to ISO 7-1, light type

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 4 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-in hose connector, ET, cyl., G 3/8 left, for hose I.D. 6, Brass
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Locking assembly BAR stainless steel 1.4401 bore 40mm
Material: Stainless steel
1.4401 (SS316).
For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft.

Stainless steel.

For low torques.

Self-centering.

Slight axial offset possible during assembly. Fit, Surface:
Due to the special design of the BAR clamping set even rough fits can
be bridged with excellent self centering capacity. Shaft and hub up to
Quality h8/H8. Surface finish for shaft and hub 10µm.

Frequency:50 Hz
Speed:2800 1/min
Shaft Output:83 W
Volume Flow:187 m³/h
Pressure:Δp s1151 Pa
Pressure:Δp t1321 Pa
Density:43862 kg/m³
Sound Pressure:69 dB(A)

24V Dc, 6W, Ip67, Glass Tube, Clear, Length 328 Mm Weight:1,5

Ferrite 1000 mm
HRA-F-102x44-AA-1000-B-B
SKU: TBAA100004
Stock: 10
Width: 102 mm
Height: 44 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 9 Homologation VDE | IMQ Dimension D x H (mm) 30 x 70 Pcs x bag 50

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Open precision housing KG-O ISO series 3 bore 62mm for open linear bearing for shaft Ø 40mm
Material: Aluminium die-cast. Light housing for linear bearings of open design, ISO Series 3 (linear bearing has to be ordered separately). The housings can be mounted standing, upside-down or horizontally. The bearing is secured in the housing against axial and radial movement with a grease nipple.

Article ID: 64654001

Bellow type FB made of molerit TH 59 size 3 D1=46mm Da=90mm Lmin=70mm Lmax=420mm travel max=350mm
Material: Molerit TH 59 Bellows protect the spindles against dirt and reduce the danger of accidents. Not yet available for size 0. Attention: The product number is only required if the bellows is to be delivered separately (not mounted on the gear unit).

Article ID: 47500310

Service unit 3-part »Standard«, Metal container, metal drip cap, Size 1, G 3/8, Input press. max. 25 bar, Control range 0.5-16 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure,
with self-relieving design, centrifugal separator and proportional lubricator.

Ball valve, Manual lever, Basic design, IT/ET, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 3/4, DN 20, PN max. 40 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 32, Stroke 20, G 1/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ25, Stroke10, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Coupling nut, M8x1, Pipe exterior Ø 4 mm, PN max. 100 bar, Stainless steel 1.4571

Angled screw-in fitting, R 1/4 o., Pipe exterior Ø 8 mm, PN max. 315 bar, AF1 17, AF2 12, galvanised steel
Male elbow, conical male thread acc. to ISO 7-1, light type

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range -1 / 0 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Reducing nipple, short type, G 1/8 o., M5 i., AF 14, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Shaft collar DIN 705 A set screw with slot bore 3mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62300300

Round gear rack made of steel C45 module 2 diameter 20mm h6 length 2000mm
Material:
Up to length 1,500mm: Steel St50K.
Length 2000mm = Steel C45k.
Outside diameter = h6 ground.

Straight teeth, milled.
Pressure angle 20°. Tooth quality 8d25 modelled on DIN 3967.

The teeth on the gear racks are manufactured using an overhead milling cutter.
This leads to negative tolerances. Dimensions ha and h0:
up to Module 2: -0,2 mm.
Module 2,5 - 4: -0,3 mm.
Module 5 - 6: -0,4 mm.




Article ID: 24163400

Frequency:50 Hz
Speed:2700 1/min
Shaft Output:61 W
Volume Flow:130 m³/h
Pressure:Δp s1177 Pa
Pressure:Δp t1254 Pa
Density:43862 kg/m³
Sound Pressure:68 dB(A

24V Dc, 6W, Ip67, Glass Tube, Diffus, L= 328 Mm Weight:1,52

Max. stack height : 240 mm
HSS-N-BA-114x022-0270-B
SKU: TGSP020270
Stock *: 0
Width: 114 mm
Neodymium sheet separators are powerful and have a compact design. They are mainly suited for the separation of oiled, sticky or perforated sheets.

Permanent magnetic
For sheets up to 3.5 mm thick
Max. stacking height 370 mm
Steel or stainless steel enclosure
With neodymium magnets

Operation

Operation of neodymium sheet separators

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 10 Homologation VDE | IMQ Dimension D x H (mm) 30 x 70 Pcs x bag 50

CH121TS General features
The packaging includes:
Electric features
LCD display: 7-segment symbols and digits.
LED, back lighting (blue) display.
Adjustable backlight duration.
Possibility to visualize Celsius or Fahrenheit temperature values.
Maximum ambient temperature 45 °C.
Settable differential.
Protection degree IP20.

Profile damper TS 84-43 diameter 84mm thread M16
Material: Co-Polyester Elastomer. The profile dampers TS are a maintenance-free, self-contained damping elements. Due to the almost linear damping characteristics it provides very smooth energy absorption along with minimum reaction loads on the machine. The excellent temperature characteristic of the material provides consistent damping performance over a temperature range of -40°C to +90°C. The low installed weight, the economic price and the long operating life of up to 1 million cycles makes this an attractive alternative to hydraulic end position damping, if the moving mass does not need to stop in an exact datum position and it is not necessary to absorb 100% of the incoming energy. The life cycle is up to 20 times longer than for urethene dampers and up to ten times longer than for rubber springs. Environment: Resistant to oil, grease seawater and to microbe or chemical attack. Excellent UV and ozone resistance. Material does not absorb water or swell. Dynamic Force Range: 533 N to 23,500 N. Temperature Range: -40°C to +90°C. Energy Absorption: 35% to 64%. Material Hardness: Shore 40D. Mounting: in any position. Impact Velocity range: up to max. 5 m/s. Mounting Bolt Torque: M4: 2 Nm. M5: 4 Nm. M6: 6 Nm. M12: 50 Nm. M16: 120 Nm. On request: special strokes, characteristics, spring rates, sizes and materials. Download Energy-Stroke Characteristics 1.5 MB   1) Max. energy capacity per cycle for continuous use. 2) For a single cycle, e.g. an emergency stop.
Article ID: 69118400

Service unit 3-part »Standard«, Metal container, metal drip cap, Size 1, G 1/4, Input press. max. 25 bar, Control range 0.5-16 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure,
with self-relieving design, centrifugal separator and proportional lubricator.

Kamlok quick-connect socket with interior thread, D type, Stainless steel 1.4401, G 3/4, for plug Ø 32 mm, Pressure max. 16 bar
High-quality, robust, universal coupling system with a safety clamp for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok stainless steel couplings are designed for use with corrosive media in the chemical and petrochemical industries, steelmaking, shipbuilding, agriculture, etc.

All female threaded couplings and connectors are with female thread sealing ring made of PTFE.

Short stroke cylinder »ASQ« single-acting, Magnet, Piston Ø 40, Stroke 30, G 1/8, Working pressure 2-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cyl.ISO 21287, single-acting, female piston rod,retr.,magnet,PistonØ16,Stroke20,M5,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

T-screw-in fitting G 1/8 o., for hose 4/6 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

T-connection, for hose 12/10 mm, AF 17, Working pressure max. 18 bar, nickel-plated brass

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 1 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Locking screw, Hexagonal socket, without flange, R 1/4, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Feather key DIN 6885 version A 2 x2 x 15 mm material C45
Material: C45K.Version A.
Article ID: 61800700

Clamp collar for splined hub DIN 14 KN 18x22 diameter 54mm steel C45Pb
Material: Steel C45Pb, from Ø 70 C45 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05.
Article ID: 64860100

Frequency:50 Hz
Speed:2720 1/min
Shaft Output:120 W
Volume Flow:233 m³/h
Pressure:Δp s1300 Pa
Pressure:Δp t1461 Pa
Density:43862 kg/m³
Sound Pressure:72 dB(A)

Dın A3 Landscape, Sheet Steel, Ral 7035 Weight:1,58

Neodymium Weakening outfeed
HRA-N-053x22-AB-0300-B-W
SKU: TGAB030041
Stock *: 0
Width: 53 mm
Height: 22 mm
Length: 300 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 11 Homologation VDE | IMQ Dimension D x H (mm) 35 x 70 Pcs x bag 50

CH123TS General features
The packaging includes:– 4 frames to provide compatibility with the most common plates– 3 coloured covers,– 3 special covers for Bticino Axolute and Ave Sistema 44, Eikon Evo,– 3 pairs of coloured adapters,– 1 pair of adapters for Bticino Matix.
LCD display: 7-segment symbols and digits.
LED, back lighting (blue) display.
Adjustable backlight duration.
Possibility to visualize Celsius or Fahrenheit temperature values.
Maximum ambient temperature 45 °C.
Settable differential.
Protection degree IP20.
Electric features
Contacts rating: 5(3)A 250Vac.
Power supply from the electric circuit – 230V-50Hz for CH123TS.
Micro disconnection (1BU).
Voltage-free switching contact.

Bevel gear made of stainless steel 1.4305 module 1.5 48 teeth i=3:1
Material: Stainless steel 1.4305. Tooth quality 8 modelled on DIN 3967 (from module 2). Crowned, milled teeth. Shaft angle 90º. The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module and ratio. At ratio 1:1, you need two pieces of the same number of teeth. At ratio uneven 1:1, you need two pieces with a different number of teeth of the same ratio.
Article ID: 36099781

Linear slide bearing PO-3 ISO series 3 for shaft diameter 40mm
Material: Polyacetal with a specific polyethylene. Linear slide bearings have the same external dimensions as the linear bearings of the ISO Series 3. The linear slide bearings should be specifically chosen if, due to unusual operating conditions, linear bearings cannot be used. Linear slide bearings feature the same mounting and securing options as the linear bearings of the ISO Series 3 and can be fitted in the same housings. Temperature range: -40°C to +80°C.
Article ID: 64624000

Microfilter »variobloc« with PC container and protective cage, 0.01 µm, Size 2, G 1, Input pressure max. 16 bar, Temp. max. 50 °C
Borosilicate filter for all applications where compliance with strict compressed air purity requirements is vital.
As the second stage downstream of the standard filter, the micro-filter removes 99.999 % of even the finest remaining particles from water, oil and dirt with practically zero residues (filter rating: 0.01 µm).

Dirt strainer, nickel-plated brass, Sieve insert mesh width 0.05 mm, Operating temp. -20°C to 110°C, G 3/4, DN 20, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.

Compact cylinder »ACP«, double-acting, Piston Ø 40, Stroke 75, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cyl.ISO 21287, single-acting, male piston rod,retr.,magnet,PistonØ16,Stroke20,M5, Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Coupling nut, M12x1.5, Pipe exterior Ø 6 mm, PN max. 315 bar, Stainless steel 1.4571