Fitting 340, conical sealing, Rp 3/8, Rp 3/8, black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Nipple for couplings I.D. 10, Hardened / nickel-plated steel, G 3/4 IT, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Bushing with exterior hexagonal, M5, AF 8, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Retaining ring DIN 472 32mm
Material: Feather steel, phosphated, oiled. Internal rings for
axial fixing a machine part inside a bore.

Article ID: 61763200

Locking assembly COM-A stainless steel 1.4401 bore 19mm size 19-47
Material: Stainless steel 1.4401 (SS316).

Clamping bush for lower torques; not self-centering.
Fit: Shaft h8, Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps. Demounting: Due to the cone angle,
the clamping set is usually released once all screws have been fully
unfastened. There a three large threads cut into the front ring, which
serve to remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61599519

Locking assembly BAR stainless steel 1.4401 bore 35mm
Material: Stainless steel
1.4401 (SS316).
For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft.

Stainless steel.

For low torques.

Self-centering.

Slight axial offset possible during assembly. Fit, Surface:
Due to the special design of the BAR clamping set even rough fits can
be bridged with excellent self centering capacity. Shaft and hub up to
Quality h8/H8. Surface finish for shaft and hub 10µm.

High performance V-belt XPZ EPDM datum length 937 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15090937

Frequency:50 Hz
Speed:2920 1/min
Shaft Output:1472 W
Volume Flow:1609 m³/h
Pressure:Δp s2266 Pa
Pressure:Δp t2384 Pa
Density:43862 kg/m³
Sound Pressure:82 dB(A

100-240V Ac, 2.000Lm, 13W, With Motion Detector Weight:1,2

Length : 150 mm
SVM-F-204x92-0150-B-F0E
SKU: SVMF040150
Stock *: 0
Advised max. installation height: 70-110 mm
Height: 92 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 1,25 Homologation Dimension D x H (mm) 25 x 57 Pcs x bag 50

EVWC4L – EVWC4 General features
EVWC4L: 4 inputs/4 outputs connection bar, with timer inputs and safety thermostat;
EVWC4: 4 inputs/4 outputs connection bar, with timer inputs and safety thermostat with circulation pump control;
Operating temperature 0°C- 45°C, RH 80% max non-condensing.
Storage temperature -10°C – 50°C.
Electric features
Power supply: 230Vac ±10% – 50Hz
Absorbed power:– 0.2VA max for EVWC4L– 2.5VA max for EVWC4
Max applicable load total 3A
Delayed fuse protections 3.15A/T (5×20 mm type)
Circulation pump relay contact range 5 (3) A – 250Vac (only for EVWC4)
Maximum cable cross-section 2.5 mm²

Rod end BR-R DIN 12240-4 series K internal tread M20 right with spherical ball bearing stainless
Material: Outer part: Stainless steel, forged, hardened. Bearing race superfinished.Inner ring and rollers: Stainless steel, hardened, superfinished. Lubrication: Aluminium-complex-soap-grease,approval according to NSF H1, -45ºC to +120ºC.If required special lubricants. Wide version. Dimensions according to DIN 648 / 12240 series K. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates. For high loads.
Article ID: 63299420

Clamp collar for splined hub DIN 14 KN 16x20 diameter 52mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05
Article ID: 64899605

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range -1/+15 bar, Ø 100
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Angled piece, interior / interior, G 1, AF 30, Operating pressure max. 60 bar, Operating temperature max. 150 °C, Bright brass

3/2-way solenoid valve »lineonline« silenced venting, Hose - hose, Hose Ø 6, NO, 24 V DC, Operating pressure 2.5 - 7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

Straight push-in fitting, round, R 1/4 o., Exterior hexagonal, Ø 8 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Angled screw-in fitting POM, G 1/8 o., for hose exterior Ø 5 mm, Working pressure max. 16 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Plug nipple »Blue Series«, reducing, plug nipple 16/12 mm, Working pressure max. 15 bar, Plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 10 bar, Ø 50
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

2-ear hose clamp, Stainless steel 1.4301 (W4), Clamping range 14.0 - 17.0 mm, Belt width 7.0 mm

Spur gear made of polyacetal resin die-cast with hub module 0.5 25 teeth tooth width 3mm outside diameter 13.5mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28102500

High performance V-belt XPZ EPDM datum length 950 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15090950

Frequency:50 Hz
Speed:2900 1/min
Shaft Output:2792 W
Volume Flow:3255 m³/h
Pressure:Δp s1786 Pa
Pressure:Δp t1985 Pa
Density:43862 kg/m³
Sound Pressure:78 dB(A

Llx-400-Bw, 100-240V Ac, 2.000Lm, 13W Weight:1,2

Length : 250 mm
BAR-HT-23-250-25-1M6-NW-B
SKU: SBANA100010-250
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 1,5 Homologation Dimension D x H (mm) 25 x 57 Pcs x bag 50

Intellitherm C31 General features
Protection cover for the adjustment keys.
Display flashing in case of low batteries charge.
Maintenance of all data during batteries replacement.
Double insulation.
Protection degree IP20.
Battery operation life of approximately 2 years.
Electric features
Contacts rating 5(3)A 250Vca.
Software class A.
Type of action: 1BU (micro disconnection).
Voltage-free switching contact.
Power supply with three 1.5 V AA alkaline long life batteries without connection to the electric circuit.

Rod end BR-R DIN 12240-4 series K internal tread M20 left with spherical ball bearing stainless
Material: Outer part: Stainless steel, forged, hardened. Bearing race superfinished.Inner ring and rollers: Stainless steel, hardened, superfinished. Lubrication: Aluminium-complex-soap-grease,approval according to NSF H1, -45ºC to +120ºC.If required special lubricants. Wide version. Dimensions according to DIN 648 / 12240 series K. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates. For high loads.
Article ID: 63299470

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range -1 / 0 bar, Ø 100
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Pressure reducing valve, G 1/4 interior / exterior, AF 17, Set pressure 8 bar, Input pressure max. 15 bar, Material: Brass
Industry, trade and repair shops often require working pressures of 15 bar or less.
These pressure reducing valves, which are screwed directly onto the tool, enable that the pressure can be reduced to the selected working pressure.

Benefits:
- Significantly reduced risk of accidents
- Longer tool life with fewer malfunctions
- Lower noise levels at the workplace

3/2-way solenoid valve »lineonline« silenced venting, Hose - hose, Hose Ø 6, NC, 24 V DC, Operating pressure 2.5 - 7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

3-way ball valve, Standard, L-hole, nickel-plated brass, Medium / ambient temp. -10 °C to 120 °C, Rp 3/8, DN 10, PN max. 40 bar
3-way ball valves with full bore for diverting media.
Applications: Water, non-toxic gases, plumbing and heating systems, oils, general industrial applications, diesel fuel

Push-in L-connector »click-clock« for hose exterior Ø 5 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 80 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Fitting 331, flat sealing, IT/ET, Rp/R 1/2, NBR seal, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galva.
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 16 bar, Ø 50
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Cutting ring, Pipe exterior Ø 22 mm, PN max. 160 bar, galvanised steel
Ferrule, light type

Spur gear made of polyacetal resin die-cast with hub module 0.5 26 teeth tooth width 3mm outside diameter 14mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28102600

High performance V-belt XPZ EPDM datum length 962 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15090962

Locknut KMK-R material 1.4301 (AISI304) with integral locking device size 10 M50x1,5
Material: Body of the nut from stainless steel 1.4301.

Reusable shaft nut with integrated locking device. Special feature of
the shaft nut is the locking insert, integrated into the nut. This
insert is threaded and thus does not cause any damage. The locking
insert is pressed against the shaft thread with a locking screw and thus
prevents the nut from turning.

Article ID: 65398565

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:2936 W
Volume Flow:3311 m³/h
Pressure:Δp s1848 Pa
Pressure:Δp t2054 Pa
Density:43862 kg/m³
Sound Pressure:78 dB(A

1200W, 5A Weight:1,2

Length : 250 mm
BAR-HT-23-250-25-1M8-NW-B
SKU: SBANA100030-250
Interface/connection dim's: Threaded hole M8 (1x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 2 Homologation VDE | IMQ Dimension D x H (mm) 25 x 57 Pcs x bag 50

ZD..NA General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 1.6 bar, Ø 100
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Quick relief valve »lineonline«, Controlled venting, Hose - thread, G 1/4, for hose Ø 8 mm, Operating pressure 1-10 bar
Exhaust can be silenced by a stainless steel silencer or conveyed using a push-in fitting with an air exhaust device.

Intermediate plate for valve terminal HDM with separated exhaust (for multi-pressure systems, 2+4 are separately exhausted)
These compact valve terminals, with a maximum flow rate of 800 Nl/min, can be individually adapted to the specific conditions of each application thanks tot he wide range of functions and various input and intermediate plates.

Since each valve terminal is a customer-specific combination of a series of individual elements, the catalogue only lists the available input, intermediate and end plates as well as the different valve discs and the 25-pin multi-pole connectors.

Suitable for filtered, unlubricated or lubricated compressed air. If lubrication is used, it must be continuous.

Monostable (non-latching) version of manual control also available on request.

The operating pressure is based on the installed input plates.

3-way ball valve, Standard, L-hole, nickel-plated brass, Medium / ambient temp. -10 °C to 120 °C, Rp 1/4, DN 8, PN max. 40 bar
3-way ball valves with full bore for diverting media.
Applications: Water, non-toxic gases, plumbing and heating systems, oils, general industrial applications, diesel fuel

Straight push-in fitting »Blue Series«, R 1/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Fitting 330, flat sealing, IT/IT, Rp/Rp 3/4, NBR seal, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galva.
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 2.5 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Locking plug »value line«, Supports 10 mm, Operating pressure max. 16 bar, Operating temp. -20 °C to 70 °C, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Two-piece clamp coupling MAT both sides bore 12mm with keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. Feather Key Groove DIN 6885/1, Tolerance P9. The torques in
the table are maximum values which can only be achieved with perfect
mounting and dimensional accuracy of the shaft.

Article ID: 60099912

Spur gear made of polyacetal resin die-cast with hub module 0.7 12 teeth tooth width 6mm outside diameter 9.8mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28201200

Clamping bush MSA bore 24mm
Material: Steel.

Mechanical, all-steel clamping elements, containing no hydraulic pressure medium. Both inner part (1) and outer part (2) have a cylindrical buttress thread with a lengthwise slot. The inner ring (3) connected to the inner part (4) has threaded studs, that create a tensioning effect when tightened.The bushes are designed for very high loads in radial as well as in axial direction. The axial runout does usually not exceed 0,02 mm. If a clamping bush without slot on the outside part is to be welded onto a workpiece, we would ask you to contact us first. Feather key grooves in the shaft do not cause any problems; simply remove the frictional corrosion.

Tolerance: Shaft h11 up to k6, Hub H7 up to H11

The values for the maximum transmittable torque and the maximum permissible axial force for the clamping bush at static load are stated in the table above. With dynamic load these values have to be reduced, i.e. divided by the operating factors listed in the adjoining table.

Operating factor: See PDF-catalog page.

1) approximate surface pressure between clamping bush and hub.


Article ID: 61502400

High performance V-belt XPZ EPDM datum length 975 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15090975

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:3288 W
Volume Flow:4033 m³/h
Pressure:Δp s1778 Pa
Pressure:Δp t1969 Pa
Density:43862 kg/m³
Sound Pressure:80 dB(A)

Stainless Steel 1.4301, With Gasket Weight:1,22