Clamp collar for splined hub DIN 14 KN 13x16 diameter 50mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05
Article ID: 64899604

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 80, Stroke 30, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 80°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Throttle check valve »Blue Series«, Supply air throttle, R 1/4 o., for hose exterior Ø 6 mm, AWorking pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pressure regulator »FUTURA«, incl. pressure gauge, Size 2, G 3/8, Input pressure max. 16 bar, Control range 0.1 - 1 bar
Diaphragm pressure regulators with self-relieving design and with excellent flow rates in modern design.
The regulator knob can be latched and locked.

Straight screw-in fitting, G 1/4 o., Pipe exterior Ø 6 mm, PN max. 630 bar, A/F1 17, A/F2 19, galvanised steel, soft seal
Male connector, parallel male thread and soft seal, heavy type

Pressure gauge connection nipple made of brass, G 1/4 bushing, G 1/8 taps, PN 400 bar

Push-in L-fitting »Blue Series«, rotating, G 3/8 i., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Plastic beakers, Contents 0.7 litres

Locking screw, Hexagonal socket and flange, G 1/4, AF 6, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Feather key DIN 6885 version A 3 x 3 x 28 mm material C45
Material: C45K.Version A.
Article ID: 61804100

High performance V-belt XPZ EPDM datum length 637 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15090637

Frequency:50 Hz
Speed:2945 1/min
Shaft Output:11346 W
Volume Flow:9606 m³/h
Pressure:Δp s3477 Pa
Pressure:Δp t3734 Pa
Density:43862 kg/m³
Sound Pressure:91 dB(A)

With Filter Mat P15/350S And Gasket Weight:0,84

1 kW

Get more coverage under your boat with Airmar’s unique, high-frequency, Chirp-ready transducers. The high-frequency band operates across a range of 150 to 250 kHz and has a fixed 25° beam for all frequencies which results in superior resolution. The constantly wide beam provides twice the coverage and excellent fish arches on the display compared to most high-frequency, narrow-beam transducer options.

The high wide is the ideal choice for both inshore and pelagic fishing, where resolution and maximum coverage are essential down to 152 m (500').

The Sealcast™ M285HW includes a plastic mounting base which is aligned to the centerline and secured inside the hull. Then it is filled with non-toxic antifreeze. The transducer is inserted into the base and adjusted for the proper deadrise offset, ensuring the beam is shooting straight down for maximum echo returns. Antifreeze is the best medium to transmit through solid fiberglass and into the surrounding water. The major benefit of an in-hull transducer is no protruding features on the exterior of the hull, making it the perfect choice for trailered or lifted boats. Designed for boats up to 11 m (36') with a solid-fiberglass hull.

Length : 530 mm
SVM-F-114x47-0530-B-F0E
SKU: SVMF010530
Stock *: 0
Advised max. installation height: 50-65 mm
Height: 47 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Fast-on doppio / M8 STUD
The MK 450 capacitors are suitable for the heavy duty motor
applications.

Intellitherm C32 General features
Front cover for batteries extraction.
Protection degree IP20.
Pollution degree 2.
Test button to check battery charge status with led indication. Pressing the button, the thermostat starts the test phase, if the batteries have sufficient charge, the LED will remain active for a few seconds and then turns OFF; if the batteries have to be replaced the LED will start to flash quickly.
Dimensions 130 x 95 x 35 mm.
Electric features
Contacts rating: 5(2)A 250Vca.
Micro disconnection 1BU .
Voltage-free switching contact.
Power supply with two 1,5 V AA alkaline long life batteries without connection to the electric circuit.
double insulation.
Pulse voltage 4000 V.

Planetary small geared motor SFP 2 with DC-motor 24V i=213:1 idle speed 16 1/min.
Housing: Motor: Steel, zinc-plated. Gearbox: made of plastic. Can be mounted in any position. Teeth: Gear set made from plastic.Bearing: Output side, plain bearing, motor side A, ball bearing, motor side B, plain bearing. Lubrication: Maintenance free grease lubrication.Motor: Brushed DC motor 24 V, interference capacitive. Change the direction of rotation by switching the polarity. Protection class acc. to EN 60529: IP 40. Operating mode as per VDE 0530: S1 at nominal torque (continous torque),S2 at higher load. Permissible radial shaft load FR: Products with 1 gear stage 30 N; with 2 gear stages 55 N; with 3 gear stages 80 N. Permissible axial shaft load FA: 35 N. Note: All values are averages, measured with the motor cold. Deviations of 10% are possible. To prevent the gearbox from being overloaded, the stated limit loads must not be exceeded. Other types (other speeds, optional incremental encoder, 12V) available on request.
Article ID: 43038224

Bevel gear made of stainless steel 1.4305 module 1 60 teeth i=4:1
Material: Stainless steel 1.4305. Tooth quality 8 modelled on DIN 3967 (from module 2). Crowned, milled teeth. Shaft angle 90º. The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module and ratio. At ratio 1:1, you need two pieces of the same number of teeth. At ratio uneven 1:1, you need two pieces with a different number of teeth of the same ratio.
Article ID: 36099593

Blocking valve pneumat. actuated, single-acting, NO, nickel-plated brass, Temp. -20°C to 150°C, Control pressure 4.2-8 bar, Rp 3/4
2/2-way check valves, specially designed for automated industrial plant engineering.
A low-price, compact, space-saving and reliable alternative to ball valves with a pneumatic rotary actuator.
These valves have a full bore and - owing to the optimised design - only minimal flow losses.
They are controlled by means of filtered compressed air.

Throttle check valve »Blue Series«, Discharge throttle, R 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pressure regulator »FUTURA«, incl. pressure gauge, Size 2, G 1/2, Input pressure max. 16 bar, Control range 0.2 - 4 bar
Diaphragm pressure regulators with self-relieving design and with excellent flow rates in modern design.
The regulator knob can be latched and locked.

Female hinge model with bushes, ISO 15552, ISO 21287, Ø80, 4 screws, 1 bolt and retainer
Female hinge model

Straight Check valve »Blue Series«, Thread to hose, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 10 bar
The non-return function of these push-in fittings prevents the air from flowing back, the unidirectional design means air flow is only possible in one direction.
These valves are available with air flow from the port to the tube or from the tube to the port.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Push-in fitting 45° »Blue Series«, rotating, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Worm thread hose clamp, Steel bright galvanised (W1), Clamping range 217.0 - 252.0 mm, Belt width 20.0 mm
Worm-drive type.

Extremely robust hose clamps for all applications where heavy loads occur and high forces are transmitted.

Hexagon-head screw slotted, a/f 13, bright galvanised steel, passivated blue.

Straight reducing supports, for hose I.D. 12/10 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Feather key DIN 6885 version A 4 x 4 x 28 mm material C45
Material: C45K.Version A.
Article ID: 61807200

High performance V-belt XPZ EPDM datum length 662 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15090662

Frequency:50 Hz
Speed:1450 1/min
Shaft Output:1314 W
Volume Flow:5078 m³/h
Pressure:Δp s764 Pa
Pressure:Δp t837 Pa
Density:43862 kg/m³
Sound Pressure:0 dB(A)

With Filter Mat P15/350S And Gasket Weight:0,84

Wind Speed and Direction
Heading
Pitch and Roll
Air Temperature
Low Temperature Operations
Barometric Pressure
Position, and speed & course over ground
Data Input/Output
3 Axis Accelerometer
Ultrasonic Transducers
GPS
3 Axis Compass
Thermistor
Heater Element
Barometric Pressure
Comma delimited ASCII/NMEA 0183 over RS422 or RS23

Size : 40 mm
HGR-SQ-040-FL-RH-M-F
SKU: TPGC040378
Stock: 62
Max. tear off force: 185 N
Advised working load: 60 N
With magnetic grippers, you automatically pick up flat steel products or sheets up to 10 mm thick. They are quick and easy to switch, and specially designed for transferring, placing or positioning using a robotic arm.Magnetic grippers serve as end of arm tooling for sheets. They even hold perforated sheets effortlessly.

For sheets up to 10 mm thick
Switching: pneumatic
For robot End-of-arm tooling
Lifting power: up to 45 kg
Permanent magnet

Application

End of arm tooling

Magnetic grippers are ideal when you want to pick up, place or position flat, steel products with a robot. The applications are very diverse, such as:

pick-and-place of steel parts
handling perforated sheets with a robot arm
unstacking workpieces from crates (bin picking)
positioning sheets in presses
stacking or unstacking hot baking tins

The high temperature gripper is suitable for this last example. For example, you can also use it to load and unload high-grade steel in a press; it is formed at high temperatures.


Operation

Switching and control of the magnet gripper

The magnet gripper switches pneumatically. This moves the magnetic field and switches it on and off.
Control can be with a 5/3 or possibly a 5/2 valve.
An activated magnet gripper does not release its load, even if the air pressure or power supply is lost. This makes it a safe and reliable end-of-arm solution.

Practical tips

Things to look out for when using magnetic grippers:
When working with thin sheets (≤1 mm) you must consider the ‘peeling off effect’. This reduces the maximum breakaway force. In this situation, it is better to create a construction with multiple smaller grippers (e.g. 40 x 40 mm) than one or two large grippers.
A sheet can be damaged when the gripper contacts the sheet. If this is a problem, choose the version with a protective polyurethane cap (friction type).
When working with oiled sheets or with high acceleration of the robotic arm, a sheet can shift position. This, too, can be prevented through use of the type with a polyurethane friction pad.
Sometimes the surface of a sheet is not flat, so the vacuum does not work. In this case, magnetic grippers are an ideal solution. The more contact surface area the better, but a magnet gripper always works on ferromagnetic steel. Thus on round shapes too.
The vacuum does not work when there are holes in the sheet; the magnet gripper does. In this case, choose a gripper with larger dimensions than the hole, and test the chosen solution thoroughly.
For small workpieces, Goudsmit has very small grippers in the assortment. They have a low overall height and give extra strength to hold the workpiece in place. For example, choose type HGR-RO-020.
For thin sheets (≤4 mm) and oily sheets that stick together, the robot sometimes picks up several sheets together. Sheet separators prevent this. They are available both in permanent and pneumatically switchable versions.

Fast-on doppio / M8 STUD
The MK 450 capacitors are suitable for the heavy duty motor
applications.

M20 General features
Minimum operating limit -15%Vn.
Maximum operating limit +10%Vn.
Closing time 10 msec.
Brass-forged valve body.
Internal parts in stainless steel (17% CR).
Gaskets in VITON (fluoroelastomer).
Temperature of the controlled fluid: -10 ÷140°C.
Testing pressure PN (DIN 2401) 25 bar.
With coil in d.c. the indicated pressure should be reduced by 60%.

Planetary small geared motor SFP 2 with DC-motor 24V i=121:1 idle speed 30 1/min.
Housing: Motor: Steel, zinc-plated. Gearbox: made of plastic. Can be mounted in any position. Teeth: Gear set made from plastic.Bearing: Output side, plain bearing, motor side A, ball bearing, motor side B, plain bearing. Lubrication: Maintenance free grease lubrication.Motor: Brushed DC motor 24 V, interference capacitive. Change the direction of rotation by switching the polarity. Protection class acc. to EN 60529: IP 40. Operating mode as per VDE 0530: S1 at nominal torque (continous torque),S2 at higher load. Permissible radial shaft load FR: Products with 1 gear stage 30 N; with 2 gear stages 55 N; with 3 gear stages 80 N. Permissible axial shaft load FA: 35 N. Note: All values are averages, measured with the motor cold. Deviations of 10% are possible. To prevent the gearbox from being overloaded, the stated limit loads must not be exceeded. Other types (other speeds, optional incremental encoder, 12V) available on request.
Article ID: 43038324

Linear bearing unit KG-3 ISO series 3 with closed linear ball bearing with angular compensation with double rubber seal for shaft Ø 16mm
Material: Housing made from extruded aluminium with a closed linear bearing of the ISO Series 3 from premium brand in top quality, with self-aligning capability that accommodates tilting. Lubricated ready-to-install.Recommended shaft tolerance h6. Spare linear bearing (that accommodates tilting) on request. * when mounting from the bottom side choose the next smaller screw size.

Article ID: 64671600

Brass ball valve, Pneumat. actuation drive, double-acting, Operating temperature -20 °C to 150 °C, Rp 3/4, DN 20, PN max. 16 bar
Ball valves with pneumatic actuator.
Pneumatic, double-piston, part-turn actuator, double-rocker principle.

Reducer, Pipe exterior Ø Female connector 16/12 mm, PN max. 630 bar, a/f1 22, a/f2 24, a/f3 30, galvanised steel
Reducer, heavy type

Pressure regulator »FUTURA«, incl. pressure gauge, Size 2, G 1/2, Input pressure max. 16 bar, Control range 0.5 - 16 bar
Diaphragm pressure regulators with self-relieving design and with excellent flow rates in modern design.
The regulator knob can be latched and locked.

Dirt strainer, Red brass, Sieve insert mesh width 0.25 mm, Operating temperature -10 °C to 150 °C, Rp 3/4, DN 20, PN max. 25 bar
For liquids, gases, steam, water, mineral, fuel and hydraulic oils, fuels and other
non-corrosive media in a liquid or gaseous state.

Angled screw-in fitting, ET conical, R 3/8, for hose 12/10 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Push-in L-fitting »Blue Series«, rotating, Rc 1/2 i., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Polycarbonate container incl. O-ring

Clamping jaw clamp, Lightweight design according to DIN 3017, Steel bright galvanised (W1), Nominal Ø 21 mm, Belt width 9 mm
Lightweight type acc. to DIN 3017.
Applications: Soft air and fuel hose types, optimal seal, high clamping force around the hose, suitable for car dealerships, repair shops and pneumatic applications.

Spur gear made of polyacetal resin die-cast with hub module 0.5 27 teeth tooth width 3mm outside diameter 14.5mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28102700

High performance V-belt XPZ EPDM datum length 670 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15090670

Frequency:50 Hz
Speed:2945 1/min
Shaft Output:9457 W
Volume Flow:8884 m³/h
Pressure:Δp s3143 Pa
Pressure:Δp t3362 Pa
Density:43862 kg/m³
Sound Pressure:90 dB(A)

24V Dc, 16W, Ip54, Glass Tube, Diffus, L=626 Mm Weight:0,88

Depth, Speed, and Temperature TRIDUCERTRIDUCER® Multisensor

Airmar’s patented UDST800 just turned your maintenance time into more cruising time—and made your boat smarter too. Get ultrasonic speed, depth, and temperature in a single thru-hull housing with no moving parts. Say goodbye to paddlewheel maintenance and hello to Smart™ technology, from the company who invented the Smart™ Sensor.


The UDST800 from AIRMAR Technology

Max. stack height : 360 mm
HSS-F-BA-154x047-0400-B
SKU: TBSP030400
Stock: 16
Width: 154 mm
Sheet separators with ferrite magnets are suitable for separating sheets in the most common situations.

Permanent magnetic
For sheets up to 4 mm thick
Max. stacking height 490 mm
Steel enclosure
Ferrite magnet

Operation

Ferrite sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Fast-on doppio / M8 STUD
The MK 450 capacitors are suitable for the heavy duty motor
applications.

ZD..NA General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Ball transfer unit 374 size 25.4 housing steel black oxide finished
Material: Housing: Steel, black oxide finish. Inside this sleeve, there is a zinc-plated ball cup. Ball cup: Steel, case hardened.  Balls: Steel 100Cr6, hardened. Medium duty ball transfer unit for medium high load, springloaded. Orientation: Ball up or horizontal. Shock loads may be higher than the stated load range. At force Fs max the end of spring travel is reached. With drain hole. Conveying speed max. 1.5m/sec. Temperature range -30°C to +100°C. * Bore size. Recommended bore tolerance: H9. Note: Due to unevenness of the running surface, there are often only three rollers carrying the weight. Therefore the chosen load rating should equal at least one third of the load. Max. distance of ball transfer units = edge length of the object divided by 2.5.
Article ID: 65437425

Precision spur gear made of steel 16MnCr5 module 3 12 teeth bore 15mm hardened and ground outside diameter 42mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 24381215

Adjustable male connector, with cone seal, G1/4 o., Pipe exterior Ø 6, PN max. 630, a/f1 19, a/f2 17, galvanised steel

Straight screw-in fitting, M33x2 o., Pipe exterior Ø 25 mm, PN max. 400 bar, A/F1 46, A/F2 41, galvanised steel
Male connector, metric thread, heavy type