Ball valve standard design, red steel lever, IT/ET, nickel-plated brass, Operating temp. -15 °C to 90 °C, G 1/2, PN max. 40 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems, agriculture.

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 25, Stroke 80, M5x0,8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3/2-way valve, pneumatically »lineonline«, NC, Hose - thread, G 3/8, for hose Ø 8 mm, Operating pressure max. 10 bar
The valves can only be used with compressed air at port 1 owing to their function.

Throttle check valve »Blue Series«, Supply air throttle, R 1/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Double threaded nipple, G 1 1/4 o., G 1 1/4 o., nickel-plated brass
Suitable for air, water, oil, steam, etc.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Bracket 121, 45°, Rp 1 1/2 IT, R 1 1/2 ET, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Knurled nut, M16x1.5, for hose 8/10 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PP
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

2-ear hose clamp, Steel bright galvanised (W1), Clamping range 7.0 - 9.0 mm, Belt width 6.0 mm
Quick and safe assembly: the two parts are simply pressed together.

Pressure gauge connection nipple made of brass, G 1/2 bushing, M20x1.5 taps, PN 1000 bar

Locking screw, Hexagonal socket and flange G 1/8 Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Connection nipple for flat suction cup, round »PFG« type, G 1/8 IT, for suction cup diameter 10 mm, I.D. 2
Connection nipples for flat suction pads

Two-piece clamp coupling MAT both sides bore 4mm without keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. The torques in the table are maximum values which can only be
achieved with perfect mounting and dimensional accuracy of the shaft.

Article ID: 60099804

Hexagon nut DIN 934 steel strength 8 zinc-plated thread M5 left handed
Material: Steel, tensile strength 8, zinc-plated.Hexagon nuts according to the old standard DIN 934 with metric ISO thread, left-handed.The standard DIN 934 was replaced by DIN EN ISO 4032 / 8673. Some of these nuts have different outer dimensions (width across flats and height). But the nuts DIN 934 are still used very often.
Article ID: 65230500

79615-1.030 DNG 8-70/S; KK-USA; Iso-H 230/400V,
50/60Hz 4,5kW; KK-Lage beachten!
Frequency:50 Hz
Speed:2870 1/min
Shaft Output:888 W
Volume Flow:1467 m³/h
Pressure:1161 Pa
Pressure:1378 Pa
Density:43862 kg/m³
Sound Pressure:84 dB(A)
ErP Compliance:2015

14770 TLR 133x62 RE 4/8 H7
Fan wheel E

Sm 20 12 - 24V Ac/Dc, 20W Weight:0,18

2 kW

Having the right tool for the job makes the job easier and gives better results. The right tool for covering deep-water haunts of swordfish, tuna, and other species is a 2 kW, low to medium-frequency transducer. The Chirp-ready PM111LM delivers the deep-water performance of the low frequency down to 1,829 m (6,000') plus the detail-delivering returns produced by the narrower beams of the medium band. Chirp technology delivers 5 to 10 times-greater detail and resolution than conventional frequencies. This transducer delivers up to 87 kHz of total bandwidth in a single installation.

The PM111LM transmits across the following bandwidths:

Low frequency 38 to 75 kHz, Medium frequency 80 to 130 kHz

Length : 100 mm
BAR-N-23-100-25-2M8-NW-B
SKU: SBAMA100040-100
Interface/connection dim's: Threaded hole M8 (2x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 1,25 Homologation Dimension D x H (mm) 25 x 57 Pcs x bag 50

Fast-on doppio / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

C10 General features
Sensing element with stainless steel diaphragm.
Tinned copper spiral capillary.
Base, cover and knob in shock-proof self-extinguishing thermoplastic material V0.
Electrical connection output with PVC cable gland.
Unit weight: 0.16 Kg.
Electric features
Two directions microswitch of instant action with AGcdO contacts.
Contact parameters in compliance with EN 60730-1: 15(6)A 250V~ 50Hz.

Open Linear slide bearing PO-3-O ISO series 3 for shaft diameter 25mm
Material: Polyacetal with a specific polyethylene. Linear slide bearings have the same external dimensions as the linear bearings of the ISO Series 3. The linear slide bearings should be specifically chosen if, due to unusual operating conditions, linear bearings cannot be used. Linear slide bearings feature the same mounting and securing options as the linear bearings of the ISO Series 3 and can be fitted in the same housings. Temperature range: -40°C to +80°C.

Article ID: 64622501

1 1-2 inch, 130 C

Service unit 3-part »multifix«, PC container, Protective cage, Size 1, G 1/4, Input pressure max. 16 bar, Control range 0.5-10 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, centrifugal separator and proportional lubricator.

Throttle check valve, Discharge throttle (»C«) quick connector Hose 10/8, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
On the version with a knurled screw, the set volumetric flow rate can be locked with the hexagon nut to obtain a fixed setting.

Stopper valve pneumatically actuated, G 1/4, G 1/4 i., G 1/8 i., Working pressure max. 10 bar, Medium / ambient temp. max. 70 °C
For high-speed positioning and stop functions as well as emergency switching (e.g. emergency stop). If a control signal is present at port 3, air can flow to and from the cylinder. If no control signal is present, the air flow to and from the cylinder is shut off, causing the cylinder to stop in the required position. Stop valves are screwed directly onto the cylinder instead of the normal pipe connections.
Note: Pilot pressure is depending on operating pressure.

3/2-way valve, pneumatically »lineonline«, NC, Thread - hose, G 3/8, for hose Ø 8 mm, Operating pressure max. 10 bar
The valves can only be used with compressed air at port 1 owing to their function.

Push-in T-fitting L-shape »metallica«, rotating, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Straight push-in connector »Blue Series«, reducing, for hose exterior Ø 8/6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Cap 300, IT, Rp 2 1/2 black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Angled hose fitting supports, for hose I.D. 8 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

2-ear hose clamp, Steel bright galvanised (W1), Clamping range 9.0 - 11.0 mm, Belt width 6.5 mm
Quick and safe assembly: the two parts are simply pressed together.

Quick-connect coupling I.D. 7.2, bright brass, G 1/4 ET, Thread coating, Operating pressure 0-12 bar, Temp. -20 °C to 100 °C
Universal, one-hand quick disconnect couplings, one side sealing, at an unbeatably low price.
The closed sleeve protects the coupling from dirt.
In combination with steel plugs, this coupling can also be used for pneumatic tools thanks to its hardened locking pins.
Couplings and plugs with thread sealing coating:
Ready-to assemble polyacrylate thread coating provides an instant, tight seal without curing. The permanently elastic sealant can be adjusted up to 45° without influencing the seal. Safe to use. Easy to assemble and disassemble.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

Cable tie, PA 6.6, black, Band: 3.6 x 300 mm, Operating temperature -45 °C to 85 °C, PU 100 pcs.
Cable tie / hose tie from polyamide 6.6 for fast, seamless and reliable bundling of cables, hoses, etc.. The black cable tie offers a higher resistance to UV radiation thanks to the enclosed "soot".
Application: electrical installations, industrial cabling, automobile cabling, marine cabling, pre-fab buildings, special applications.

Connection nipple for flat suction cup, round »PFG« type, G 1/8 IT, for suction cup diameter 15 mm, I.D. 2
Connection nipples for flat suction pads

Spur gear made of polyacetal resin die-cast with hub module 0.5 15 teeth tooth width 3mm outside diameter 8.5mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28101500

Locknut UW with integral locking device M50x1.5 stainless steel 1.4301
Material: Body of the nut: Stainless steel 1.4301.

Locking insert: Stainless Steel.

With these slot nuts no additional lock washers or keyways are required.
No keyway or washer required for roller bearing. Designed for easy
assembly. Maintenance-free construction. The bolt thread has to meet the
medium quality of ISO 965. Please note: Ensure that there are at least
two or three full threads behind the locking insert. This slot nut must
not be used on shafts with keyway. Lubricate the nut when screwing it
onto the shaft. Larger thread diameters can be supplied on request.
Function: This system consists of a shaft nut and a special
spring, acting as friction ring. This special spring is integrated into
the upper part of the nut. Due to the lead of the thread the special
spring locks itself between shaft and nut. The
system is locked in any position!
Article ID: 65399465

Frequency:50 Hz
Speed:2865 1/min
Shaft Output:1071 W
Volume Flow:1587 m³/h
Pressure:Δp s1268 Pa
Pressure:Δp t1555 Pa
Density:43862 kg/m³
Sound Pressure:81 dB(A)

15077-1.750 Fan Base
ST (SW)
Material: sheet Steel
Varnishing: RAL9005 Deep Black

Le-150-L, 24V Dc, 3W Weight:0,18

1 kW

The B265LM, Chirp-ready transducer is a perfect, mid to deep-depth transducer. The huge bandwidth includes many of the most popular frequencies for targeting top gamefish. This 1 kW, powerhouse delivers clear target details, bottom discrimination, as well as bait and game-fish separation at all depths. The low-frequency band provides deep-water performance down to 914 m (3,000') and is a good choice when scouting an area or fishing in deeper depths. The medium-frequency band is excellent for identifying targets suspended close to the bottom, on structure, and within the water column.

The included, high-performance fairing improves broadband performance at speeds over 30 knots (34 MPH).

Low frequency 42 to 65 kHz, Medium frequency 85 to 135 kHz

Ferrite 1000 mm
HRA-F-052x17-AA-1000-B-B
SKU: TBAA100001
Stock: 25
Width: 52 mm
Height: 17 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Climatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 1,5 Homologation Dimension D x H (mm) 25 x 57 Pcs x bag 50

Fast-on doppio / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

C10 General features
Sensing element with stainless steel diaphragm.
Tinned copper spiral capillary.
Base, cover and knob in shock-proof self-extinguishing thermoplastic material V0.
Electrical connection output with PVC cable gland.
Unit weight: 0.16 Kg.
Electric features
Two directions microswitch of instant action with AGcdO contacts.
Contact parameters in compliance with EN 60730-1: 15(6)A 250V~ 50Hz.

Oil-level window SR 160 sight 139 x 18mm
Material: Aluminium with inserted disk of natural glass and Perbunan® seal.Rectangular shape, clear readability. Also diesel-oil resistant.Temperature resistant up to +120ºC.
Article ID: 68113400

1 1-2 inch, 130 C

Service unit 3-part »multifix«, PC container, Protective cage, Size 1, G 3/8, Input pressure max. 16 bar, Control range 0.5-10 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, centrifugal separator and proportional lubricator.

Hose sleeve, ball nipple, hose I.D. 6, coupl. nut G 1/8 Stainless steel, Max. working pressure 60 bar, Max. operating temp. 150 °C

Short stroke cylinder, double-acting, Magnet, Piston Ø 20, Stroke 5, M5, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Closing nipple locking on both sides, Stainless steel 1.4305, G 1/8 IT, I.D. 4.3, Operating pressure max. 250 bar
Hydraulic couplings, both sides sealing, for liquid media acc. to ISO 7241, B Series.

Areas of application: machine and plant engineering, manufacturing industry, chemical / pharmaceutical industry, automotive, food technology.

Push-in T-fitting L-shape »metallica«, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Straight push-in connector, Plug nipple »Blue Series«, red., hose exterior Ø 6, plug nipple 8, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, M27x2 o., Pipe exterior Ø 20 mm, PN max. 400 bar, A/F1 36, A/F2 32, galvanised steel, soft seal
Male connector, metric thread and soft seal, heavy type

1-ear hose clamp with insert ring, Stainless steel 1.4301 (W4), Clamping range 9.0 - 10.5 mm, Belt width 7.8 mm

Hexagonal counter nut, M10x1, AF 14, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Quick-connect coupling I.D. 7.2, bright brass, G 3/8 ET, Thread coating, Operating pressure 0-12 bar, Temp. -20 °C to 100 °C
Universal, one-hand quick disconnect couplings, one side sealing, at an unbeatably low price.
The closed sleeve protects the coupling from dirt.
In combination with steel plugs, this coupling can also be used for pneumatic tools thanks to its hardened locking pins.
Couplings and plugs with thread sealing coating:
Ready-to assemble polyacrylate thread coating provides an instant, tight seal without curing. The permanently elastic sealant can be adjusted up to 45° without influencing the seal. Safe to use. Easy to assemble and disassemble.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

Cable tie, PA 6.6, natural, Band: 3.6 x 300 mm, Operating temperature -45 °C to 85 °C, PU 100 pcs.
Cable tie / hose tie from polyamide 6.6 for fast, seamless and reliable bundling of cables, hoses, etc.. The black cable tie offers a higher resistance to UV radiation thanks to the enclosed "soot".
Application: electrical installations, industrial cabling, automobile cabling, marine cabling, pre-fab buildings, special applications.