Wear part set, for pressure regulator DRV 200, Standard design, G 1 1/4

3-way stainless steel ball valve, Pneumat. actuation drive, L-hole, Operating temp. -20°C to 70°C, Rp 1, DN 25, PN max. 63 bar
3-way cock, reduced bore.
Pneumatic actuators, double- or single acting version and integrated end-position feedback.

Standardised interfaces:
Actuator/valve interface: Four or eight female threads in the actuator housing acc. to EN ISO 5211.
Actuator/control valve interface: Acc. to NAMUR or VDI/VDE 3845.
Actuator/signalling device interface: Acc. to VDI/VDE 3845 (NAMUR).

Straight screw-in fitting, Soft seal, G 1/2, Pipe exterior Ø 18 mm, PN max. 315 bar, Stainless steel 1.4571
Version with parallel thread and soft seal made of NBR.

Rubber-metal MGE diameter 40mm height 25mm inner thread M8
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Steel, zinc plated. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68510403

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 8.5 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Wear part set, for pressure regulator DRV 200, Standard design, G 1 1/2

Hose rupture valve »Hose Guard« Aluminium, Aluminium piston, Temp. -20 °C to 120 °C, G 2 IT/IT, Input pressure max. 18 bar
Efficient protection for ruptured hoses or pipes in pneumatic systems. Preset to permit normal air consumption by pneumatic tools.
Hose Guard detects a rupture in a hose or pipe and interrupts the supply of compressed air in a fraction of a second apart from a minimal residual flow. Unaffected parts of the compressed air system remain fully pressurised, so that the damaged hose or segment can be replaced without difficulty. Once the ruptured hose or pipe has been repaired, the replaced segment gradually fills to its working pressure level. As soon as this occurs, Hose Guard opens the line again for normal operation.

Installation: Upstream of a coupling (connector between hard piping and junction box/coupling) and downstream of a service unit.

»Hose Guard«
- Protects personnel, machinery and plant against damage if a pneumatic system or hose ruptures
- Complies with the EU standard DIN EN ISO 4414: 2010, 2011-04 - § 5.4.5.11
- Is reliable and tamper-proof
- Can be installed in any pneumatic system

3/2-way valve, pneumatically »lineonline«, NC, Thread - hose, G 1/4, for hose Ø 6 mm, Operating pressure max. 10 bar
The valves can only be used with compressed air at port 1 owing to their function.

Rubber-metal MGE diameter 20mm height 10mm inner thread M6 stainless steel 1.4301
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Stainless steel 1.4301. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68910201

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 9.5 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Compact cyl.ISO 21287,single-acting,female piston rod,retr.,magnet,PistonØ50,Stroke15,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Female hinge model, ISO 15552, Ø250, 4 screws, 1 bolt and retainer

3/2-way valve, pneumatically »lineonline«, NC, Hose - thread, G 1/4, for hose Ø 6 mm, Operating pressure max. 10 bar
The valves can only be used with compressed air at port 1 owing to their function.

Rubber-metal MGE diameter 20mm height 11mm inner thread M6 stainless steel 1.4301
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Stainless steel 1.4301. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68910202

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 10.3 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Compact cyl.ISO 21287, single-acting, male piston rod,retr.,magnet,PistonØ50,Stroke15,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Male hinge model with bushes, ISO 15552, Ø250, with 4 screws

Reducing sleeve 246, IT/ET, Rp 3, R 2 1/2, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Rubber-metal MGE diameter 20mm height 12mm inner thread M6 stainless steel 1.4301
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Stainless steel 1.4301. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68910203

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 10.5 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Compact cyl.ISO 21287,single-acting,female piston rod, ext.,magnet,PistonØ50,Stroke15,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3-way ball valve, L-hole, Stainless steel 1.4408, G 2, DN 38.1, Operating temperature -20 °C to 180 °C, PN max. 63 bar
With L or T-bore, reduced bore.
Version for sealing on all sides with integrated ISO flange plate (ISO 5211).
The lever can be turned 360° to allow several switching variants.

Made of plastic PA6 GF 30.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

Rubber-metal MGE diameter 20mm height 13.5mm inner thread M6 stainless steel 1.4301
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Stainless steel 1.4301. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68910204

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 11 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Compact cyl.ISO 21287, single-acting, male piston rod ext.,magnet,PistonØ50,Stroke15,G1/8, Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3-way ball valve, T-hole, Stainless steel 1.4408, Operating temperature max. 160 °C, G 2, DN 50, PN max. 63 bar
With L or T-bore, reduced bore.

Version for sealing on all sides with integrated ISO flange plate (ISO 5211).
The lever can be turned 360° to allow several switching variants.

Trunnion mounting, »CA/CB« type for compact cylinder »ACP«, Piston Ø 100
Male hinge model, »CA« type / Female hinge model, »CB« type

Rubber-metal MGE diameter 20mm height 15mm inner thread M6 stainless steel 1.4301
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Stainless steel 1.4301. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68910205

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 13 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Push-in T-fitting, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar, Stainless steel 1.4404
For use with aggressive media and in areas susceptible to corrosive outside
influences, in the food processing industry and in hygienic and sanitary applications.

2/2-way solenoid valve brass, NC, pilot operated, 230 V, 50 - 60 Hz, Medium temperature -20 °C to 85 °C, Rp 2, PN 0.35 - 9 bar
Standard series, proven over many years, available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Swing safety coupling I.D. 5.5, ARO 210, Steel, NPT 1/4 IT, Operating pressure max. 25 bar, Temp. -20 °C to 100 °C
Swing safety coupling with free passage.
The plug-in nipple is inserted into the coupling body and rotated by an approx. 90° motion to make the connection. As soon as the "red ring" clicks into the intended slot then a secure connection has been made. To release the connection again, the "red ring" must be pulled out and the plug-in nipple is swivelled to the stopper into the starting position. Venting is done during uncoupling through a vent hole on the back side of the coupling.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive.

Straight adaptor with o-ring thread G3/8A tube outer diameter 12mm
Material: Body: Brass, nickle-plated.

Article ID: 86011238

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 16 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Stainless steel ball valve, 2-piece, IT/IT thread, G 1, DN 25, Operating temperature -20 °C to 180 °C, PN max. 63 bar

Piston rod-free cylinder, double-acting, Magnet, Piston Ø 32, Stroke 300, G 1/4, Working pressure 1 - 8 bar, Temp. -10 °C to 80 °C
These double-acting cylinders can also be supplied with strokes greater than 5 m, providing the stroke length is approximately equal to the overall length. They are equipped with magnets as standard for indicating the position as well as pneumatic, adjustable end position cushioning. Limit switches and hydraulic shock absorbers can be mounted as add-on modules.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Swing safety coupling I.D. 5.5, ARO 210, Steel, NPT 3/8 IT, Operating pressure max. 25 bar, Temp. -20 °C to 100 °C
Swing safety coupling with free passage.
The plug-in nipple is inserted into the coupling body and rotated by an approx. 90° motion to make the connection. As soon as the "red ring" clicks into the intended slot then a secure connection has been made. To release the connection again, the "red ring" must be pulled out and the plug-in nipple is swivelled to the stopper into the starting position. Venting is done during uncoupling through a vent hole on the back side of the coupling.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive.

Elbow adaptor tube outer diameter 6mm
Material: Body: Brass, nickle-plated.

Article ID: 86210600

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1 1/4, AF 50, Trigger pressure 6.6 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Stainless steel ball valve 1.4408, 3-piece, weld-on studs, Full passage, Operating temp. -20 °C to 150 °C, DN 15, PN max. 63 bar

Stainless steel ball valve, 2-piece, IT/IT thread, G 3, DN 76, Operating temperature -20 °C to 180 °C, PN max. 40 bar

Swing safety coupling I.D. 5.5, ARO 210, Steel, NPT 1/2 IT, Operating pressure max. 25 bar, Temp. -20 °C to 100 °C
Swing safety coupling with free passage.
The plug-in nipple is inserted into the coupling body and rotated by an approx. 90° motion to make the connection. As soon as the "red ring" clicks into the intended slot then a secure connection has been made. To release the connection again, the "red ring" must be pulled out and the plug-in nipple is swivelled to the stopper into the starting position. Venting is done during uncoupling through a vent hole on the back side of the coupling.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive.

Plate wheel KRL without hub 08 B-1 1/2x5/16" 19 teeth material steel
Material: Low-carbon steel, not hardable. Pre-bored. General
dimensions: B1 = 7,2 mm, c = 1,3 mm, r3 = 13 mm. Other dimensions: See
the table.

Article ID: 10521900

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 1.6 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Filter regulator »G«, with PC container, Protective cage, Mounting bracket, 5 µm, Size 300, G 3/8, Input pressure max. 10 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator.
The pressure setting can be locked by pushing the button down.

Corner safety valve, for saturated steam, Red brass, Operating temp. -10 to 135 °C, G 3/4, AF 32, Trigger pressure 0.3 bar
Type-tested, TÜV – SV. 749 D/G

Swing safety coupling I.D. 5.5, ARO 210, Steel, NPT 1/4 ET, Operating pressure max. 25 bar, Temp. -20 °C to 100 °C
Swing safety coupling with free passage.
The plug-in nipple is inserted into the coupling body and rotated by an approx. 90° motion to make the connection. As soon as the "red ring" clicks into the intended slot then a secure connection has been made. To release the connection again, the "red ring" must be pulled out and the plug-in nipple is swivelled to the stopper into the starting position. Venting is done during uncoupling through a vent hole on the back side of the coupling.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive.

Sprocket KRK with hub 081 1/2 X 1/8" 13 teeth material polyacetal resin
Bores ISO H8. Metal inlays at the hub with custom bore, feather keyways or threads for set screw available on request, depending on the amount and size ordered. General dimensions: B1 = 3 mm, c = 1,3 mm, r3 = 13 mm. Other dimensions: See the table.

Article ID: 10251300

Replacement blade, rectangular shape, max. hose exterior Ø 20 mm, 1 piece

Filter regulator »GA«, with PC container, Protective cage, Mounting bracket, 5 µm, Size 400, G 3/8, Input pressure max. 10 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator. The pressure setting can be locked by pushing the button down.

Standard cylinder »SE« ISO 15552, double-acting, Piston Ø 125, Stroke 700, G 1/2, Working pressure 1 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on three sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Swing safety coupling I.D. 5.5, ARO 210, Steel, NPT 3/8 ET, Operating pressure max. 25 bar, Temp. -20 °C to 100 °C
Swing safety coupling with free passage.
The plug-in nipple is inserted into the coupling body and rotated by an approx. 90° motion to make the connection. As soon as the "red ring" clicks into the intended slot then a secure connection has been made. To release the connection again, the "red ring" must be pulled out and the plug-in nipple is swivelled to the stopper into the starting position. Venting is done during uncoupling through a vent hole on the back side of the coupling.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive.

Timing belt pulley MXL material aluminium 32 teeth for belt width 012
Material: Aluminium similar EN AW2017A. Flanges zinc-plated steel. Pre-bored (from a Teeth Number of 22). Profile MXL = 0,08" = 2.032 mm. Belt width 012 = 3.2 mm.
Article ID: 18113200

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 1, AF 41, Trigger pressure 1.5 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Filter regulator »GA«, with PC container, Protective cage, Mounting bracket, 5 µm, Size 400, G 1/2, Input pressure max. 10 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator. The pressure setting can be locked by pushing the button down.

2-way brass ball valve, Pneumat. actuation drive double-acting, Operating temperature max. 70°C, Rp 2 1/2, DN 65, PN max. 25 bar
2-way cock, full bore.
Pneumatic actuators, double- or single acting version and integrated end-position feedback.

Swing safety coupling I.D. 5.5, ARO 210, Steel, NPT 1/2 ET, Operating pressure max. 25 bar, Temp. -20 °C to 100 °C
Swing safety coupling with free passage.
The plug-in nipple is inserted into the coupling body and rotated by an approx. 90° motion to make the connection. As soon as the "red ring" clicks into the intended slot then a secure connection has been made. To release the connection again, the "red ring" must be pulled out and the plug-in nipple is swivelled to the stopper into the starting position. Venting is done during uncoupling through a vent hole on the back side of the coupling.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive.

Bevel gear made of polyketone die-cast module 2 15 teeth i=2:1 bore 10mm
Material: Polyketone resin, die-cast, ivory-colored. Shaft angle 90º. Version: injection-moulded. Bores from Module 1.5 machined. Lower friction leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C, due to the load. Note for ordering: The bevel gears only run as a pair at the stated ratio. These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module and ratio. At ratio 1:1, you need two pieces of the same number of teeth. At ratio uneven 1:1, you need two pieces with a different number of teeth of the same ratio.
Article ID: 35605601

Corner safety valve, for saturated steam, Red brass, Operating temp. -10 to 135 °C, G 1, AF 41, Trigger pressure 2.5 bar
Type-tested, TÜV – SV. 749 D/G