Plate wheel KRL without hub 06 B-1 3/8x7/32" 12 teeth material steel
Material: Low-carbon steel, not hardable. Pre-bored. General dimensions: B1 = 5,3 mm, c = 1,0 mm, r3 = 10 mm. Other dimensions: See the table.
Article ID: 10121200

Plug-in connector for I.D.11, check valve, ISO 6150 C, Steel, Sleeve I.D. 13, Temp. -20°C to 100°C, Opening pressure min. 0.6 bar

Pressure regulator, continuous pressure supply »multifix-mini«, Size 0, G 1/4, Input pressure max. 16 bar, Control range 0.2-6 bar
Diaphragm pressure regulators with self-relieving design for mounting side by side.
The pressure setting can be locked by pushing the button down.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line.

Microfilter for high pressures up to 60 bar, manual bleeder valve, 0.01 µm, G 1, Brass container, Operating temp. 0 °C to 90 °C
Fine filter for all applications with particularly strict compressed air purity requirements. Micro-filters should always be used in conjunction with a standard filter connected upstream to trap coarse impurities and protect the micro-filter inserts.

Soft PVC workshop hose set, Quick-connect coupling I.D. 7.2, Hose Ø 14.5x9, PN at 20 °C max. 15 bar, Length 5 m
Highly flexible hose for compressed air applications in workshop areas. Assembled with brass stem and brass quick disconnect coupling DN 7.2 optional with pushbutton safety coupling DN 7.4 and galvanised steel stem.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Internal tab washer DIN 462 inner-ø 14mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65261401

Inner chain link type 4/B for roller chain DIN ISO 606 20 B - GL pitch 1 1/4x3/4" with straight plates
Similar to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.
Article ID: 10900100GL

Plug-in connector for I.D.11, check valve, ISO 6150 C, Steel, Sleeve I.D. 16, Temp. -20°C to 100°C, Opening pressure min. 0.6 bar

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 16, Stroke 30, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Compressed air hose set with hose rupture valve »Hose guard«, PU hose, G 3/8 ET, Hose Ø 13x8, Hose length 10 m
Braided PU hose with integrated rupture hose valve type »Hose Guard« and screwed stem with a G 3/8 or G 1/2 male thread.

Filter insert, for fine filter »Bavaria« for potable water, DVGW tested, R 3/4, R 1 and R 1 1/4

Internal tab washer DIN 462 inner-ø 16mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65261601

Neoprene timing belt 130 XL 025 65 teeth Lw 330.2mm belt width 6.35mm
Material: Neoprene with glas-fibre tensile member. Teeth surface fabric-coated. Timing belt with inch dimensions, classical shape with trapezoid teeth. Profile XL = 1/5" = 5.08 mm. Belt width 025 = 6.35 mm. Temperature range -20º to +100ºC.
Article ID: 18062600

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 20, Stroke 600, G 1/8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 16, Stroke 40, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

2-way stainless steel ball valve, Pneumat. actuation drive, single-acting, Operating temp. -20°C to 70°C, Rp 1/2, PN max. 63 bar
2-way cock, 3-piece, full bore.
Pneumatic actuators, double- or single acting version and integrated end-position feedback.

Standardised interfaces:
Actuator/valve interface: Four or eight female threads in the actuator housing acc. to EN ISO 5211.
Actuator/control valve interface: Acc. to NAMUR or VDI/VDE 3845.
Actuator/signalling device interface: Acc. to VDI/VDE 3845 (NAMUR).

Screw-in hose connector, G 3/4 o., for hose I.D. 4, Stainless steel, Max. working pressure 60 bar, Max. operating temp. 150 °C

Internal tab washer DIN 462 inner-ø 18mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65261801

Spur gear made of polyketone die-cast with hub module 0.7 52 teeth tooth width 6mm outside diameter 37,8mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28205201

Service unit 2-part »FUTURA-mini«, Metal container, Standard pressure gauge, Size 0, G 1/4, Control range 0.1 - 4 bar, Semi-auto.
Two-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 16, Stroke 50, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Intermediate flange blocking flap, Pneumat. actuation drive, double-acting, Operating temp. -15°C to 120°C, DN 65, PN max. 16 bar
Butterfly valves with pneumatic actuator. Pneumatic actuators, double- or single acting version.
For water/steam, seawater, salt water, ester, ketones, alkalis, caustic soda, sodium hydroxide.
Not recommended for hydrocarbons, oils or greases.

Reducing nipple, Long, G 1/2 o., G 3/4 i. AF 32 Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Internal tab washer DIN 462 inner-ø 20mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65262001

Spur gear made of polyketone die-cast with hub module 1 19 teeth tooth width 9mm outside diameter 21mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28301901

Service unit 2-part »FUTURA-mini«, Metal container, Standard pressure gauge, Size 0, G 1/4, Control range 0.5 - 8 bar, Semi-auto.
Two-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 12, Stroke 150, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Workshop hose, Soft PVC, Temperature range -20 °C to 60 °C, Hose Ø 23x16, PN at 23 °C max. 15 bar, Roller length 50 m
Highly flexible hose for compressed air applications in workshop areas (compressed air feed for pneumatic tools, equipping assembly stations, etc.).
Thanks to the even fabric reinforcement, this hose combines high pressure resistance, very good handling and high mechanical strength with excellent bond adhesion.
The high level of ozone resistance further enhances the hose's durability and reliability.

Pipe double nipple, G 2, Length 60 mm, Working pressure max. 10 bar, Medium / ambient temperature max. 90 °C, Bright brass

Internal tab washer DIN 462 inner-ø 22mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65262201

Flanged bush BBP bore 20mm polyamide 6.6 outer diameter 26mm length 15mm flange diameter 32mm
Material: Thermoplastic polyamide 6.6, die cast. Color: natural.Polyamide is very well suited for the manufacture of plain bearings due to its good sliding characteristics and strong wear resistance even at dry-running conditions and because of its sufficient mechanical strength and excellent corrosion resistance. Surface pressure max.: 18 N/mm², dependant on sliding speed and bearing temperature Sliding Speed:2 m/s Lubrication: usually not required Bearing clearance: about 0.01 mm per mm shaft-Ø Bearing temperature: Should not exceed 80°C. With thin-walled parts, the frictional heat is dissipated extremely well. Coefficient of linear expansion: 8 x 10^-5 Moisture absorption max.: 7.5% Moisture absorption at 20°C and 50% rel. humidity: 2.4% Mounting hole: tolerance H7
Article ID: 62383500

Service unit 2-part »FUTURA-mini«, Metal container, Standard pressure gauge, Size 0, G 1/4, Control range 0.5 - 10 bar, Semi-auto.
Two-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Cross fitting, Pipe exterior Ø 18 mm, PN 315, A/F1 32, A/F2 24, galvanised steel
Cross-fitting, light type

Standard cylinder, ISO 15552, double-acting, Piston Ø 100, Stroke 250, G 1/2, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches can be mounted in two T-slots on the same side as the compressed air supply.
The version with a 125 mm bore is provided with fixing accessories on three sides as standard.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Reducing nipple short type G 1 1/2 o., G 1 i. AF 55 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Internal tab washer DIN 462 inner-ø 24mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65262401

Metric threaded bar DIN 976-1 form A M3 x 1000mm right handed stainless steel A4 marked with red paint
Material: Stainless steel V4A. Threaded bars according to DIN 976-1 shape A (ex DIN 975), with metric ISO thread. Length either 1 m or 2m. Marked with red paint.
Article ID: 65099403

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ80, Stroke45,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Removable Double threaded nipple, flat sealing, G 1 1/2 i., AF1 76, AF2 56, Working pressure max. 10 bar, Stainless steel 1.4408

Hose coupling set, PUR, Safety coupling, Medium / ambient temperature max. 60 °C, Hose Ø 16x11, PN max. 16 bar, Length 15 m
Spiral or straight polyurethane hose, completely assembled with DN 7.6 safety coupling and steel plugs.

Coupling
Safety coupling made of steel / nickel-plated brass for high flow rates, specially designed for all applications susceptible to severe mechanical wear.
Strong, impact and vibration-resistant design for demanding environments.

Polyurethane hose
Extremely flexible spiral hose with excellent kink resistance and insensitive to dirt.
Combines high tear, tensile and impact strength with a long service life and optimal ageing qualities.
This hose is additionally characterised by outstanding resistance to abrasion and resistance to UV.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Reducing nipple short, G 1 1/2 o., G 1 1/4 i. AF 55 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Internal tab washer DIN 462 inner-ø 28mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65262801

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ80, Stroke45, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Made of plastic PA6 GF 30.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

Filter regulator »Standard«, PC container, Protective cage, 40 µm, Size 4, G 1, PE max. 16 bar, 0.5 - 10 bar, pilot controlled
Reversible diaphragm pressure regulators, independent of inlet pressure, with selfrelieving design,
combined with a centrifugal separator.

Straight screw-in fitting, Soft seal, G 1/2, Pipe exterior Ø 15 mm, PN max. 315 bar, Stainless steel 1.4571
Version with parallel thread and soft seal made of NBR.

Internal tab washer DIN 462 inner-ø 30mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65263001

Angle joint DIN 71802 type CS with safety circlip size 13 thread M8 right with nut steel zinc-plated
Material: Steel zinc-plated. With threaded bolt and hexagon nut,
ball stud hardened.
Form C: Without circlip.
Form CS: With circlip.
Thread: Gewindeausführung rechts = right handed thread in the
socket. Gewindeausführung links = left handed thread in the socketmarked
with a circumferential groove.

* Pivoting angle reduced by circlip.

Article ID: 63660800

Captive swivel safety coupling I.D. 6, ISO 6150 C, Steel, 2-stage, G 1/4 IT, red, max. 25 bar, Temp. -15 °C to 200 °C
High quality, robust and long lifetime one-hand rotation secure coupling.
A secure connection is made by pushing in the plug-in nipple that clicks in audibly. Uncoupling is done by rotating the sleeve anti-clockwise. For this, the pending pressure in the coupling and line are vented, however the plug-in nipple is not completely released via a safety latch.
The plug-in nipple can only be pulled out after a clockwise rotation of the sleeve. The colour and shape coding of the coupling and plug-in nipple makes it possible only to couple to the same colours.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive, mining.

Filter regulator »Standard«, Metal container and pressure gauge, 40 µm, Size 4, G 3/4, PE max. 25 bar, 0.5 - 16 bar, pilot contr.
Reversible diaphragm pressure regulators, independent of inlet pressure, with selfrelieving design,
combined with a centrifugal separator.

Wear part set, for pressure regulator DRV 200, Standard design, G 3/8

Internal tab washer DIN 462 inner-ø 32mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65263201

Microfilter »variobloc« with PC container, 0.01 µm, Size 2, G 1/2, Input pressure max. 16 bar, Medium / ambient temp. max. 50 °C
Borosilicate filter for all applications where compliance with strict compressed air purity requirements is vital.
As the second stage downstream of the standard filter, the micro-filter removes 99.999 % of even the finest remaining particles from water, oil and dirt with practically zero residues (filter rating: 0.01 µm).

Captive swivel safety coupling I.D. 6, ISO 6150 C, Steel, 2-stage, G 3/8 IT, red, max. 25 bar, Temp. -15 °C to 200 °C
High quality, robust and long lifetime one-hand rotation secure coupling.
A secure connection is made by pushing in the plug-in nipple that clicks in audibly. Uncoupling is done by rotating the sleeve anti-clockwise. For this, the pending pressure in the coupling and line are vented, however the plug-in nipple is not completely released via a safety latch.
The plug-in nipple can only be pulled out after a clockwise rotation of the sleeve. The colour and shape coding of the coupling and plug-in nipple makes it possible only to couple to the same colours.

This coupling meets ISO standard DIN EN ISO 4414, EN 983.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive, mining.

Service unit 2-part »variobloc«, Metal container incl. viewing tube and metal drip cap, Size 2, G 1, Input pressure max. 20 bar
Two-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator and a proportional lubricator.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Wear part set, for pressure regulator DRV 200, Standard design, G 1/4

Lockwasher DIN 5406 Type MB 5 inner diameter 25mm stainless steel 1.4618
Material: Stainless steel 1.4618 (AISI 201).Safety plates for locknuts DIN 981. A keyway is required on the shaft thread.
Article ID: 65399544

Internal tab washer DIN 462 inner-ø 35mm plain steel
Material: Steel.Lockwashers (safety plates) for locknuts DIN 1804. A keyway is required on the shaft thread.After adjusting or fastening the nut, the sheet edge must be beaded into one slot of the nut.
Article ID: 65263501

Microfilter »variobloc« with PC container, 0.01 µm, Size 2, G 3/4, Input pressure max. 16 bar, Medium / ambient temp. max. 50 °C
Borosilicate filter for all applications where compliance with strict compressed air purity requirements is vital.
As the second stage downstream of the standard filter, the micro-filter removes 99.999 % of even the finest remaining particles from water, oil and dirt with practically zero residues (filter rating: 0.01 µm).