Dın A7 High, Plastic Transparent Weight:0,04

Applications
Level measurement
Automation control
Proximity
Obstacle avoidance
Robotics
Specs English
Specs German
Specs Spanish

Max. stack height : 45 mm
HSS-F-BA-073x029-0075-B
SKU: TBSP000075
Stock: 71
Width: 73 mm
Sheet separators with ferrite magnets are suitable for separating sheets in the most common situations.

Permanent magnetic
For sheets up to 4 mm thick
Max. stacking height 490 mm
Steel enclosure
Ferrite magnet

Operation

Ferrite sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 12 Homologation VDE | IMQ Dimension D x H (mm) 35 x 70

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

Lockshield valve series 158 General features
Available with chrome frame finish
Micrometric regulation
Maximum pressure 10 bar
Auger retention with EPDM O Ring
Teng retention with O Ring
Thread according to UNI ISO 228
Body made of brass

HEXAGONAL NIPPLE - STAINLESS STEEL 316

Information

Hexagonal nipple - Stainless steel 316> DiamA " very available: from DN6 to DN50- Gas thread> Nominal pressure of the hexagonal nipple: - 20 bar A 20AdegC- 16 bar A 100AdegC> Standard ISO 228-1

Precision shaft steel with shaft support Ø 25h6 x 1200mm long
Material: Steel 1.1213 (Cf53), hardened and ground, hardness 62±2 HRC, diameter tolerance ISO h6. Material support: Extruded aluminium. Length: Either 600 mm or 1200 mm. Ready-to-use, mounted, supported linear shafts to be used with open linear bearings or open linear bearing units. The shafts are supported over their entire length. The shaft supports have mounting holes for mounting them on a base plate. Unit can be shortened by the customer using an angle grinder. Longer versions on request.

Article ID: 64742504

internal term: 3-4 inch, 90 C 10,0 bar water One way: no 2 way with a standing inner tube :no 2 way with a standing inner tube: yes

internal term: P-ND One way : yes 2 way with a standing inner tube: no
190 C 17,0 bar water
Universal use – cooling, heating, clamping
With bellows sealing
Cartridge fast change CD-cartridge-design
Sealingmaterial ceramics/graphite
Ballbearings (can be relubricated)
No elastomers – therefore no temperature and chemical resistance problems
No loose parts, f.e. springs
Robust and less influence of dirty media
Self supporting – no additional support necessary
Available in stainless steel

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

1 1-2 inch, 120 C internal term: RTO One way: yes 2 way with a standing inner tube: No 2 way with rotating inner tube: No

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 80, Stroke 5, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 80°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Hose sleeve, ball nipple, hose I.D. 6, coupl. nut G 1/4 Stainless steel, Max. working pressure 60 bar, Max. operating temp. 150 °C

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 25, Stroke 60, M5, Working pressure max. 10 bar, Temp. -10°C to 60 °C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3/2-way valve, Pneumatic, »3A«, monostable, NC, G 1/8, Operating pressure 1.5 - 8 bar, Temperature range max. 70 °C
3/2-way pilot valves
- Pneumatic -

Quick-connect coupling I.D. 5 »connect line« nickel-plated brass, Sleeve I.D. 4, Operating pressure 0-35 bar, Temp. -20°C to 100°C
Low-priced, one-hand quick disconnect couplings, one side sealing, compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive, food technology.

Hose sleeve, ball nipple, hose I.D. 12, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Push-in T-fitting »click-clock«, rotating, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

1-ear hose clamp with insert ring, Steel bright galvanised (W1), Clamping range 13.0 - 15.3 mm, Belt width 8.8 mm
An absolutely safe all around setting is ensured by the pre-mounted insert ring. Suitably for use with soft and sensitive hose material.

Straight fitting, Pipe exterior Ø 5 mm, PN bar 100, AF1 12, AF2 11, galvanised steel
Union, very light type

Straight Check valve »Blue Series«, Hose to thread, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
The non-return function of these push-in fittings prevents the air from flowing back, the unidirectional design means air flow is only possible in one direction.
These valves are available with air flow from the port to the tube or from the tube to the port.

Pipe double nipple, R 3/8, Length 80 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Clamping ring, for hose 9/12 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PP
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Push-in L-fitting »Blue Series«, rotating, Rc/R 1/4 i./o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »click-clock«, rotating, G 1/2 o., for hose exterior Ø 14 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Coupling nut, M7x0.75, for hose 5/3 mm, AF 8, Working pressure max. 18 bar, nickel-plated brass

Push-in L-fitting »Blue Series«, Self-locking, R 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Cutting ring, Pipe exterior Ø 15 mm, PN max. 315 bar, galvanised steel
Ferrule, light type

Replacement sieve for dirt strainers made of brass, for connection size G 1/4, 3/8, 1/2, mesh width 0.2 mm, DN 8

Nipple, I.D. 5, locking on both sides, Bright brass, G 1/8 ET, AF 14, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Straight screw-in fitting, M27x2 o., Pipe exterior Ø 20 mm, PN max. 400 bar, A/F1 36, A/F2 32, galvanised steel
Male connector, metric thread, heavy type

Straight hose connection supports, for hose I.D. 5 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

The switching outputs of the thermal controller can be programmed as

-two-point controller with alarm
-three-point controller with alarm contact
-two-stage controller with alarm contact
-three-stage controller.

Beside the standby key there is a second key to set functions, which can be variously parametered. 900210.007

Retaining ring DIN 472 15mm
Material: Feather steel, phosphated, oiled. Internal rings for
axial fixing a machine part inside a bore.

Article ID: 61761500

Timing belt pulley HTD 8M material grey cast iron 90 teeth for belt width 30mm for taper bush 2517
Material: Up to a Teeth Number of 72 phosphated steel, from a
Teeth Number of 80 grey cast iron GG25 phosphated.Ready-to-install,
for use with taper-bushings. Taper-bushings are available for varios
shaft diameters and have to be ordered seperately.

In this youtube video we show the mounting and demounting of taper
bushes: Video clip (3.5
Minutes)
Article ID: 17477245

Clamp collar for splined hub DIN 14 KN 46X54 diameter 100mm steel C45
Material: Steel C45Pb, from Ø 70 C45 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05.
Article ID: 64861400

Pressure Ranges -1 to 700 bar
Accuracy +/-1%
100mm + 160mm Gauge Sizes
Glycerine Filled

Rotating joint for high pressure and high speed
Single input / output line

Frequency:50 Hz
Speed:2815 1/min
Shaft Output:54 W
Volume Flow:248 m³/h
Pressure:Δp s407 Pa
Pressure:Δp t519 Pa
Density:1.2 kg/m³
Sound Pressure:65 dB(A)

Clip Made Of Stainless Steel (Set 2 Pieces) Weight:0,04

Applications
Level measurement
Automation control
Proximity
Obstacle avoidance
Robotics
Flow
Specs English
Specs German
Specs Spanish

Diameter : 18 mm
HEPM-EM-D018-011-SW
SKU: GM17801
Stock: 12
Max. holding force: 45 N
Interface/connection dim's: Threaded hole M3
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 12,5 Homologation VDE | IMQ Dimension D x H (mm) 35 x 70

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

Lockshield valve series 158 General features
Available with chrome frame finish
Micrometric regulation
Maximum pressure 10 bar
Auger retention with EPDM O Ring
Teng retention with O Ring
Thread according to UNI ISO 228
Body made of brass

WELDING NIPPLE LENGTH 50 MM - STAINLESS STEEL 316L

Information

MAC / le - 316L stainless steel> DiamA " very available: from DN8 to DN50 - Gas Thread> Characteristics (c) ristics of the mAC / le - 316L stainless steel: Tube RoulA (c) / SoudA (c) - Schedule 20S> Nominal pressure of the mAC / le nozzle: PN50> ISO standard 7/1

KL-retainer steel zinc plated size 3 for bolt diameter 3mm
Material: Spring steel, zinc plated.KL retainers are used to fix parts on shafts or bolts in axial direction. They can get mounted and dismounted very easily. They are intended for connections which must be disassembled more often. It is necessary to ensure that there is no unwanted strong contact to the retainer, because it is easily to remove.* Max. transmittable force, static, on shafts with min. strength 500 N/mm².** Depending on the shaft diamater.
Article ID: 63780001

Precision shaft steel with shaft support Ø 40h6 x 600mm long
Material: Steel 1.1213 (Cf53), hardened and ground, hardness 62±2 HRC, diameter tolerance ISO h6. Material support: Extruded aluminium. Length: Either 600 mm or 1200 mm. Ready-to-use, mounted, supported linear shafts to be used with open linear bearings or open linear bearing units. The shafts are supported over their entire length. The shaft supports have mounting holes for mounting them on a base plate. Unit can be shortened by the customer using an angle grinder. Longer versions on request.

Article ID: 64744003

Timing belt pulley HTD 14M material steel 40 teeth for belt width 40mm for taper bush 2517
Material: Up to a Teeth Number of 56 phosphated steel, from a Teeth Number of 64 phosphated grey cast iron GG25.Ready-to-install, for use with taper-bushings. Taper-bushings are available for varios shaft diameters and have to be ordered seperately. In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 17677120

internal term: 1-4 inch, 90 C 10,0 bar water One way: no 2 way with a standing inner tube :no 2 way with a standing inner tube: yes

internal term: P-ND One way : yes 2 way with a standing inner tube: no
190 C 17,0 bar water
Universal use – cooling, heating, clamping
With bellows sealing
Cartridge fast change CD-cartridge-design
Sealingmaterial ceramics/graphite
Ballbearings (can be relubricated)
No elastomers – therefore no temperature and chemical resistance problems
No loose parts, f.e. springs
Robust and less influence of dirty media
Self supporting – no additional support necessary
Available in stainless steel

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

1 1-2 inch, 130 C internal term: SRO One way: no 2 way with a standing inner tube: Yes 2 way with rotating inner tube: No

Round cylinder, double-acting, with magnet, Piston Ø 40, Stroke 400, G 1/4, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Version with magnetic piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

L-multi-distributor »Blue Series«, 4-fold, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 25, Stroke 60, M5, Working pressure max. 10 bar, Temp. -10°C to 60 °C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3/2-way valve, Pneumatic, »3A«, monostable, NO, G 1/8, Operating pressure 1.5 - 8 bar, Temperature range max. 70 °C
3/2-way pilot valves
- Pneumatic -

Quick-connect coupling I.D. 5 »connect line«, nickel-plated brass, G 1/8 ET, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
Low-priced, one-hand quick disconnect couplings, one side sealing, compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive, food technology.

Hose sleeve, ball nipple, hose I.D. 13, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.