REO444R1B 0.15V
Code = REO444R1B0.15EG
60V Flange Mounted is used as speed monitoring device. They convert rotating movement (RPM) into a proportional DC voltage with almost nil propagation delay and have no need for an energy supply. Radio Energie tachogenerator is most often used when mounted on to the back of a DC Motor. It supplies the connected DC drive with a voltage that is linear to speed typically expressed as a voltage against speed e.g. 60V/1000RPM.
IP54
Part Number /0000025
The REO444 range are no longer 'UL' or 'CSA' approved.

60V Flange Mounted is used as speed monitoring device. They convert rotating movement (RPM) into a proportional DC voltage with almost nil propagation delay and have no need for an energy supply. This unit differs from a standard unit by having Temperature Drift Compensation, CA Grade Brushes and 5000rpm max speed.
The REO444R1CB006CA Tachogenerator Radio Energie tachogenerator is most often used when mounted on to the back of a DC Motor. It supplies the connected DC drive with a voltage that is linear to speed typically expressed as a voltage against speed e.g. 60V/1000RPM.
Part Number /0000029
The REO444 range are no longer 'UL' or 'CSA' approved.

60V Flange Mounted is used as speed monitoring device. They convert rotating movement (RPM) into a proportional DC voltage with almost nil propagation delay and have no need for an energy supply. This unit differs from a standard unit by having Temperature Drift Compensation, CA Grade Brushes and 5000rpm max speed.
The REO444R1CB006CA Tachogenerator Radio Energie tachogenerator is most often used when mounted on to the back of a DC Motor. It supplies the connected DC drive with a voltage that is linear to speed typically expressed as a voltage against speed e.g. 60V/1000RPM.
Part Number /0000029
The REO444 range are no longer 'UL' or 'CSA' approved.

White, With Strain Relief Weight:0,01

350 W

The plastic P7 is part of our Shorty™ Series, designed for boats with limited headroom. Compared with the P19, the P7 housing is 28 mm (1.10") shorter for mounting in tight spots. Its low-profile is nearly flush and minimizes drag with only 5 mm (3/16") extending outside of the hull, eliminating turbulence for exceptional high-speed echo sounder performance.

Neodymium (NdFeB) 60 N
PM-TE-N-SG-D13x4.5xM5x8
SKU: GM17623
Stock: 222
Size: 13 mm
Thread (M): M5
Compact magnet systems with a steel shell and with a threaded end for easy mounting. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded end are available in various sizes in neodymium and ferrite.

Available in various qualities
Easy to install
Deliverable from stock

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 1,25 Homologation Dimension D x H (mm) 25 x 57

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

25 – 27 series ring and control knob General features
Ring and control knob for C02 thermostats series

HEXAGON HEAD PLUG WITH COLLAR, BSP CYLINDRICAL THREAD (CASTING) - STAINLESS STEEL 316

Information

MAC plug / hexagonal tAate With base - Stainless steel 316> DiamA " very available: from DN6 to DN50- Gas thread> Nominal pressure of the mAC plug / hexagonal tAate With base: - 20 bar A 20AdegC- 16 bar A 100AdegC> Standard ISO 228-1DIN 910

Slip shaft with joints PW bore 10H7 with keyway DIN 6885-1 tolerance JS9 on both sides min. length 170mm max. length 230mm steel
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Spline shaft C40. Max. Operating Angle per Joint 45°. Other lengths on request. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63182000N

Precision shaft block GW ISO series 3 for shaft diameter 50mm
Material: Extruded aluminium. Light Design, matching linear-bearing units of ISO Series 3. Shaft blocks are practical and robust machine elements, that provide a simple way of attaching the guiding shaft of the linear bearings on the respective machine parts. They allow true to size and, most important, cost efficient constructions.

Article ID: 64645000

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

internal term: P-ND One way : yes 2 way with a standing inner tube: no
190 C 17,0 bar water
Universal use – cooling, heating, clamping
With bellows sealing
Cartridge fast change CD-cartridge-design
Sealingmaterial ceramics/graphite
Ballbearings (can be relubricated)
No elastomers – therefore no temperature and chemical resistance problems
No loose parts, f.e. springs
Robust and less influence of dirty media
Self supporting – no additional support necessary
Available in stainless steel

internal term: 3-8 inch, 90 C 100,0 bar coolant One way: yes 2 way with a standing inner tube :no 2 way with a standing inner tube: no

3-8 inch, 130 C internal term: RSRO One way: no 2 way with a standing inner tube: No 2 way with rotating inner tube: Yes

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 50, Stroke 800, G 1/4, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

L-multi-distributor »Blue Series«, 2-fold, rotating, G 3/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 25, Stroke 55, M5x0,8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ12, Stroke50, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure spring 0 - 8 bar, galvanised, Colour: black-blue

Straight screw-in fitting, R 1/4 o., Pipe exterior Ø 6 mm, PN bar 630, A/F1 17, A/F2 17, galvanised steel
Male connector, conical male thread acc. to ISO 7-1, heavy type

Straight hose connection supports, for hose I.D. 10 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Flange fastening, »FA« type for compact cylinder »ACP«, Piston Ø 50
Flange model, »FA« type

Push-in T-fitting »click-clock«, rotating, R 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Locking screw, Hexagonal socket without flange G 1/4 Stainl. st. 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Straight screw-on fitting, G 3/8 i., for hose 6/4 mm, AF 20, Working pressure max. 18 bar, nickel-plated brass

Locking screw, Exterior hexagonal and flange, G 1/4, AF 13, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Screw-on hose connector, IT, cyl. G 1/8, for hose I.D. 9 , AF 14 Brass
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

T-piece 130, IT/IT/IT, Rp 1/2, T-branch reducing Rp 1/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galva.
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

T-screw-in fitting »value line«, rotating, G 1/4 o., for hose exterior Ø 10 mm, Operating pressure max 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/8, Goods class 1.6, Measurement range 0 - 16 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Closing cap (hexagonal design), G 1, AF 36, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Double threaded nipple, Hexagonal, R 3/8, AF 18, Working pressure max. 20 bar, Stainless steel 1.4408

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/8, Goods class 1.6, Measurement range 0 - 10 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

2-ear hose clamp »blow line«, galvanised steel, Chrome III coated, Clamping range 31.0 - 34.0 mm
Quick and safe assembly: the two parts are simply pressed together.

Bracket 121, 45°, Rp 3/8 IT, R 3/8 ET, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Locking screw, Exterior hexagonal, G 3/4, AF 32, nickel-plated brass, Max. working pressure 25 bar Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Captive nipple I.D. 5, Bright brass, G 1/4 ET, green, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C

Clamping nut, M12x1, for hose 8/6 mm, AF 14, Operating pressure 0 - 10 bar, Temperature -10 °C to 60 °C, POM

The controller ST58-GB1TV.10 was developed for simple thermostatic applications. The unit disposes of a connection for resistance sensor PTC or Pt100. It is supplied with a voltage of 12-24V AC or 12-36V DC and has an exit relay with an Ohm maximum electric load of 16A. Inductive loads can be connected with up to max. 2,2A permanent current. 900144.002

Retaining ring DIN 471 4mm
Material: Feather steel, phosphated, oiled. External rings for
axial fixing a machine part on a shaft.

Article ID: 61740400

Miniature Static Pressure
Small & Compact
Ranges -1 to 25 bar

Rotating joint with aluminium- or brassdesign for water
internal term: PRO One way: yes 2 way with a standing inner tube: No 2 way with rotating inner tube: No

For Lv/Gv 100 5 Pc. Weight:0,01

600 W

Our P79 is a dual-frequency, depth only, in-hull transducer that easily adjusts to hull deadrise angles up to 22°.The P79 includes a plastic mounting base which is aligned to the centerline and secured inside the hull. Then it is filled with nontoxic antifreeze. The transducer is inserted into the base and adjusted for the proper deadrise offset, insuring the beam is shooting straight down for maximum echo returns. The coolant provides the best medium to transmit through the solid fiberglass and into the surrounding water. The major benefit of in-hull transducers is no protruding features on the exterior of the hull, making it the perfect choice for trailered or lifted boats. Designed for smaller boats up to 8 m (25') with a solid fiberglass hull.

Neodymium (NdFeB) 40 N
PM-BA-N-BR-D10h6x20
SKU: GM17303
Stock: 32
Diameter: 10 mm
A: 8 mm
Height: 20 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 1,5 Homologation Dimension D x H (mm) 25 x 57

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

25 – 27 series ring and control knob General features
Ring and control knob for C02 thermostats series

WELDING NIPPLE LENGTH 50 MM - STAINLESS STEEL 316L

Information

MAC / le - 316L stainless steel> DiamA " very available: from DN8 to DN50 - Gas Thread> Characteristics (c) ristics of the mAC / le - 316L stainless steel: Tube RoulA (c) / SoudA (c) - Schedule 20S> Nominal pressure of the mAC / le nozzle: PN50> ISO standard 7/1

Slip shaft with joints PW both sides bore 12H7 telescoped length 200mm max. length 270mm steel outer diameter 25mm
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Spline shaft C40. Max. Operating Angle per Joint 45°. Other lengths on request. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63182600

Precision shaft steel with shaft support Ø 12h6 x 600mm long
Material: Steel 1.1213 (Cf53), hardened and ground, hardness 62±2 HRC, diameter tolerance ISO h6. Material support: Extruded aluminium. Length: Either 600 mm or 1200 mm. Ready-to-use, mounted, supported linear shafts to be used with open linear bearings or open linear bearing units. The shafts are supported over their entire length. The shaft supports have mounting holes for mounting them on a base plate. Unit can be shortened by the customer using an angle grinder. Longer versions on request.

Article ID: 64741203

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

internal term: P-ND One way : yes 2 way with a standing inner tube: no
190 C 17,0 bar water
Universal use – cooling, heating, clamping
With bellows sealing
Cartridge fast change CD-cartridge-design
Sealingmaterial ceramics/graphite
Ballbearings (can be relubricated)
No elastomers – therefore no temperature and chemical resistance problems
No loose parts, f.e. springs
Robust and less influence of dirty media
Self supporting – no additional support necessary
Available in stainless steel

internal term: 3-8 inch, 90 C 10,0 bar water One way: no 2 way with a standing inner tube :yes 2 way with a standing inner tube: no

1-2 inch, 130 C internal term: SRO One way: no 2 way with a standing inner tube: Yes 2 way with rotating inner tube: No

Spherical trunnion mounting, ISO 15552, for standard cylinder, Piston Ø 125, with 4 screws
Articulated male hinge model