Short stroke cylinder, double-acting, Magnet, Piston Ø 25, Stroke 5, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Hose with garage connector, Length 50 cm, G 1/4, swiveling, for tyre gauges standard type

Reducing piece 241, ET/IT, R 1 1/2 o., Rp 1 1/4 i., Operating temp. -20°C to 300°C, black malleable cast iron,Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Rem. Double threaded nipple, con. seal.R 1 o., R 1 o.nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Straight Bulkhead fitting, Pipe exterior Ø 15 mm, PN max. 315 bar, AF1 27, AF2 30, AF3 27, galvanised steel
Bulkhead connector, light type

Replacement seal in NBR, for GEKA couplings of series »GEKA plus«, (excluding couplings with screw rings), Temp. -10 °C to 90 °C

Feather key DIN 6885 version A 2 x 2 x 14 mm material C45
Material: C45K.Version A.
Article ID: 61800600

Adjusting ring DIN 705 A set screw with slot bore 36mm zinc-plated
Light-duty series. With set screw DIN EN 27 434 made from steel, zinc-plated. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62388036

Spur gear made of steel C45 with hub module 3 90 teeth tooth width 25mm outside diameter 276mm
Material: C45.

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.




Article ID: 23309000

High performance V-belt XPZ EPDM datum length 2137 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15092137

Frequency:50 Hz
Speed:2800 1/min
Shaft Output:128 W
Volume Flow:276 m³/h
Pressure:Δp s1249 Pa
Pressure:Δp t1470 Pa
Density:43862 kg/m³
Sound Pressure:72 dB(A)

With Z-Line-Filter (F5) Weight:4,6

Diameter : 90 mm
HEPM-EP-D090-048-SW
SKU: GM17859
Stock: 3
Max. holding force: 1200 N
Interface/connection dim's: Threaded hole M8
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

K10CKIT General features
Cable composition: thermoplastic material with a mechanical protection and earth braiding and an external protective sheath
Cable diameter 9 mm
Cable length:– K10C3KIT 3 m– K10C6KIT 6 m– K10C9KIT 9 m– K10C14KIT 14 m
Maximum room temperature powered 65 ° C
Minimum installation room temperature -5 °C
Thermostat temperature scale ON +5°C / OFF +15°C
Minimum storage room temperature -20 ÷ -25°C
Protection rating IPX7
Electric features
Power supply 230V-50Hz
Constant power delivered ~10W/m

Double-acting standard cylinder ISO 15552 cylinder diameter 32mm stroke 200mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80132200

Clamp collar for splined hub DIN 14 KN 21x25 diameter 62mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05
Article ID: 64899606

Suction and pressure hose, Lightweight design, Temperature -15°C to 60°C, Hose Ø 29.6x25 mm, PN at 23 °C max. 5 bar, Roll of 50 m
Transparent PVC spiral hose with green, impact-resistant, hard PVC spiral and
smooth inner layer (prevents sediment).
Applications: Construction industry, agriculture, engineering, gardening and landscaping

Straight reducer, Pipe exterior Ø Female connector 18/10 mm, PN max. 315 bar, a/f1 27, a/f2 32, a/f3 19, galvanised steel
Straight reducers, light type

Round cylinder, ISO 6432, double-acting, Magnet, Piston Ø 20, Stroke 80, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 80°C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Adjustable straight screw-in fitting, Sealing cone, Nut M12x1.5 i., G 1/8, Pipe exterior Ø 6 mm, PN max. 315 bar, Stainless steel
Version with parallel thread and soft seal made of NBR.

Reducing piece 241, ET/IT, R 1 1/2 o., Rp 1 i., Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Kink protection spiral for swing safety couplings »R-SC« DN 5.5 - DN 11, for hose 12x8, polyamide unbreakable

Straight push-in bulkhead connector »click-clock«, M24x1, for hose exterior Ø 14 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Plug nipple »click-clock«, for hose exterior Ø 4 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 80 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Feather key DIN 6885 version A 6 x 6 x 28 mm material C45
Material: C45K.Version A.
Article ID: 61812500

Adjusting ring DIN 705 A set screw with slot bore 38mm zinc-plated
Light-duty series. With set screw DIN EN 27 434 made from steel, zinc-plated. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62388038

Spur gear made of steel C45 with hub module 3 100 teeth tooth width 25mm outside diameter 306mm
Material: C45.

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.




Article ID: 23310000

High performance V-belt XPZ EPDM datum length 2160 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15092160

Frequency:50 Hz
Speed:2800 1/min
Shaft Output:333 W
Volume Flow:447 m³/h
Pressure:Δp s1468 Pa
Pressure:Δp t1819 Pa
Density:43862 kg/m³
Sound Pressure:80 dB(A

Pk 50 Hk + Ag 50, 50W , 24V Dc Weight:4,6

Belt type : Rubber, with cleats (EP400/3 4+2mm)
RUBBER BELT EP400/3-4+2
SKU: 45.3050003
Stock *: 0
Suitable for belt width: 600 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Intellitherm C67 General features
Front cover for batteries extraction.
Display flashing in case of low batteries charge.
Maintenance of all data during batteries replacement.
Microprocessor and CMOS circuits.
Double insulation.
Protection degree IP20.
Unit weight 0.22 Kg.
Electric features
Contacts rating: 5(3)A 250Vac.
Type of action: 1BU (micro disconnection)
Voltage-free switching contact.
Power supply with two 1,5 V AA alkaline long life batteries without connection to the electric circuit.

hose clamp DIN 3017-1 type W1 steel zinc plated diameter range 16-27mm band width 9mm
Material: Steel, zinc-plated (type W1). High-performance hose clamps with worm gear thread, for fixing hoses, bellows and for similar usage. Band width 9 mm. Band thickness 0.6 mm. With hexagon screw head size 7 mm, with cross recess and slot. Other sizes and versions on request.
Article ID: 63811027

Double-acting standard cylinder ISO 15552 cylinder diameter 32mm stroke 250mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80132250

Polyurethane timing belt T10 width 50mm Lw 1210mm 121 teeth 50 T10/1210
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Classical shape with trapezoid teeth. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. T timing belts only run on T pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16489200

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ100,Stroke150,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight reducer, Pipe exterior Ø Female connector 22/12 mm, PN max. 160 bar, a/f1 32, a/f2 36, a/f3 22, galvanised steel
Straight reducers, light type

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 32, Stroke 100, G 1/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pneumatic logic elements, YES, Techno-polymer, DN 2.7, Temperature range -10 °C to 60 °C, Working pressure 0 to 8 bar
Pneumatic logic elements are available with five different functions: OR, AND, NOT, YES, MEMORY.
All elements have an adapter for the Ω-rail (DIN EN 50022) integral with the body.

Reducing piece 241, ET/IT, R 1 1/2 o., Rp 1/2 i., Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in Y-connector, Plug nipple 3 mm »Blue Series« mini, for hose exterior Ø 3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Worm thread hose clamp, Steel bright galvanised (W1), Clamping range 242.0 - 277.0 mm, Belt width 20.0 mm
Worm-drive type.

Extremely robust hose clamps for all applications where heavy loads occur and high forces are transmitted.

Hexagon-head screw slotted, a/f 13, bright galvanised steel, passivated blue.

Replacement seal in NBR, for GEKA couplings, for old series, Temperature range -10 °C to 90 °C

Spur gear made of steel C45 with hub module 3 114 teeth tooth width 25mm outside diameter 348mm
Material: C45.

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.




Article ID: 23311400

High performance V-belt XPZ EPDM datum length 2287 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15092287

Frequency:50 Hz
Speed:2830 1/min
Shaft Output:452 W
Volume Flow:417 m³/h
Pressure:Δp s2099 Pa
Pressure:Δp t2341 Pa
Density:43862 kg/m³
Sound Pressure:80 dB(A)

Stainless Steel 1.4301, With Gasket Weight:4,8

Neodymium 300 mm
HRA-N-103x22-AA-0300-B-W
SKU: TGAA030043
Stock: 1
Width: 103 mm
Height: 22 mm
Water-resistant: yes
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

CH130ARR General features
KIT composed of: thermostat and remote actuator
Auxiliary input for minimum window and/or thermostat contact using an external probe.
Screwed terminals.
Double insulation.
Electric features
Power supply from a remote actuator.
Remote actuator with 5 output relays, voltage 250 Vac.
Contacts rating 5(3)A.

Profile damper TS 90-47 diameter 90mm thread M16
Material: Co-Polyester Elastomer. The profile dampers TS are a maintenance-free, self-contained damping elements. Due to the almost linear damping characteristics it provides very smooth energy absorption along with minimum reaction loads on the machine. The excellent temperature characteristic of the material provides consistent damping performance over a temperature range of -40°C to +90°C. The low installed weight, the economic price and the long operating life of up to 1 million cycles makes this an attractive alternative to hydraulic end position damping, if the moving mass does not need to stop in an exact datum position and it is not necessary to absorb 100% of the incoming energy. The life cycle is up to 20 times longer than for urethene dampers and up to ten times longer than for rubber springs. Environment: Resistant to oil, grease seawater and to microbe or chemical attack. Excellent UV and ozone resistance. Material does not absorb water or swell. Dynamic Force Range: 533 N to 23,500 N. Temperature Range: -40°C to +90°C. Energy Absorption: 35% to 64%. Material Hardness: Shore 40D. Mounting: in any position. Impact Velocity range: up to max. 5 m/s. Mounting Bolt Torque: M4: 2 Nm. M5: 4 Nm. M6: 6 Nm. M12: 50 Nm. M16: 120 Nm. On request: special strokes, characteristics, spring rates, sizes and materials. Download Energy-Stroke Characteristics 1.5 MB   1) Max. energy capacity per cycle for continuous use. 2) For a single cycle, e.g. an emergency stop.
Article ID: 69119000

Polyurethane timing belt T10 width 50mm Lw 1240mm 124 teeth 50 T10/1240
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Classical shape with trapezoid teeth. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. T timing belts only run on T pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16489300

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ100,Stroke150, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled fitting, Pipe exterior Ø 25 mm, PN max. 400 bar, A/F1 46, A/F2 36, galvanised steel
Union elbow, heavy type

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 32, Stroke 30, G 1/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled piece, 90°, interior / exterior, G 1 1/2, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Reducing piece 241, ET/IT, R 1 1/2 o., Rp 3/4 i., Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Reducing nipple, short, G 3/4 o., G 1/8 i. AF 19 Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Coupling package for blocking several components, incl. O-ring, for »multifix«, Size 5, G 1

Screw-on hose connector, G 1/8 i., for hose I.D. 9, nickel-plated brass
Previous design. Can be delivered as long as in stock.
After sale the delivery is made in new optimised geometry.

Suitable for air, water, oil, steam, etc.

Adjusting ring DIN 705 A set screw with slot bore 42mm zinc-plated
Light-duty series. With set screw DIN EN 27 434 made from steel, zinc-plated. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62388042