Suitable for belt width : 1000 mm
RHP-F406A08-100-RSD-BA
SKU: RHAF40100000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 800 mm
RHP-F406A08-080-RSD-BA
SKU: RHAF40080000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 650 mm
RHP-F406A08-065-RSD-BA
SKU: RHAF40065000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 1400 mm
RHP-B406A08-140-RSD-BA
SKU: RHAN40140000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 1200 mm
RHP-B406A08-120-RSD-BA
SKU: RHAN40120000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 1000 mm
RHP-B406A08-100-RSD-BA
SKU: RHAN40100000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 800 mm
RHP-B406A08-080-RSD-BA
SKU: RHAN40080000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 1200 mm
RHP-B324A08-120-RSD-BA
SKU: RHAN32120000
Stock *: 0
Diameter: 324 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 1000 mm
RHP-B324A08-100-RSD-BA
SKU: RHAN32100000
Stock *: 0
Diameter: 324 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 800 mm
RHP-B324A08-080-RSD-BA
SKU: RHAN32080000
Stock *: 0
Diameter: 324 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 650 mm
RHP-B324A08-065-RSD-BA
SKU: RHAN32065000
Stock *: 0
Diameter: 324 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 400 mm
RHP-H153R18-040-RSB-BA
SKU: RHAH150361
Stock *: 0
Diameter: 152 mm
Magnet field strength (flux density) (±10%): 9000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Working width : 2000 mm
RMD-20-32-RN-H-OR-20S2
SKU: E0026240
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RN-H-OR-20S2
SKU: E0026236
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RN-H-OR-20S2
SKU: E0026228
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RN-H-OR-15S2
SKU: E0026118
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RN-H-OR-15S2
SKU: E0026090
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 2000 mm
RMD-20-32-RS-H-OR-20S2
SKU: E0062424
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RS-H-OR-20S2
SKU: E0062422
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RS-H-OR-20S2
SKU: E0062406
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RS-H-OR-15S2
SKU: E0062396
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 2000 mm
RMD-20-32-RN-P-OR-30S2
SKU: E0025966
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RN-P-OR-30S2
SKU: E0025962
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RN-P-OR-30S2
SKU: E0025960
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RN-P-OR-30S2
SKU: E0025957
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RN-P-OR-30S2
SKU: E0020871
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 2000 mm
RMD-20-32-RS-P-OR-30S2
SKU: E0062133
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RS-P-OR-30S2
SKU: E0062121
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RS-P-OR-30S2
SKU: E0062110
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RS-P-OR-30S2
SKU: E0062100
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 2000 mm
RMD-20-32-RN-B-OR-30S2
SKU: E0025970
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RN-B-OR-30S2
SKU: E0025952
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RN-B-OR-30S2
SKU: E0024388
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RN-B-OR-30S2
SKU: E0010858
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RN-B-OR-30S2
SKU: E0025947
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 2000 mm
RMD-20-32-RS-B-OR-30S2
SKU: E0061241
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RS-B-OR-30S2
SKU: E0061218
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RS-B-OR-30S2
SKU: E0061211
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RS-B-OR-30S2
SKU: E0061190
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RS-B-OR-30S2
SKU: E0061188
Stock *: 0
Field strength (flux density) (±10%): 3000 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 0.5 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 2000 mm
RMD-20-32-RN-F-OR-30S2
SKU: E0026054
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RN-F-OR-30S2
SKU: E0026052
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RN-F-OR-30S2
SKU: E0026050
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RN-F-OR-30S2
SKU: E0026048
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RN-F-OR-30S2
SKU: E0026046
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 2000 mm
RMD-20-32-RS-F-OR-30S2
SKU: E0061182
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1500 mm
RMD-15-32-RS-F-OR-30S2
SKU: E0061173
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 1000 mm
RMD-10-32-RS-F-OR-30S2
SKU: E0061164
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 800 mm
RMD-08-32-RS-F-OR-30S2
SKU: E0061130
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RS-F-OR-30S2
SKU: E0061054
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RS-H-OR-15S2
SKU: E0061826
Stock *: 0
Field strength (flux density) (±10%): 8000 gauss (on shell) gauss
Magnetic field depth: 30 mm
Min. Fe-particle size that can be caught: 30 µm (sporadically)
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Working width : 600 mm
RMD-06-32-RS-P-OR-30S2
SKU: E0062088
Stock *: 0
Field strength (flux density) (±10%): 6000 gauss (on shell) gauss
Magnetic field depth: 150 mm
Min. Fe-particle size that can be caught: 0.1 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Product inlet size : 400 mm
SETK-lenastar
SKU: E_dummy
Stock: 0
Hygienic: Yes
Separate particles: Fe particles > 0.2µm, Weakly magnetic particles > 0.1 mm
These 'LenaStar' pharma drum magnets have a 12,000 gauss strong neodymium magnet drum. They remove ferromagnetic particles from 0.20 µm and weak magnetic particles from 0.1 mm from your raw materials during the production process. No production stop needed.The LenaStar is very hygienically executed. Smoothly polished, sloping surfaces, dismountable parts, water-resistant, product fabric does not adhere to the surface.

Capture weakly magnetic particles from 0.1 mm
Capture Fe particles from 0.2 µm
Max. particle size 10 mm
In stainless steel enclosure
Neodymium magnet (12,000 gauss at shell)

Application

Removal of weakly- and paramagnetic contaminants

The 'LenaStar' pharma type drum magnets in housing can be used in free-fall pipelines, or after a vibrating chute. Due to their extremely strong magnetic drum of 12,000 gauss, they remove the smallest ferromagnetic, or even weakly magnetic and paramagnetic contaminants.
 
For removal of weakly and paramagnetic particles, it is essential that you feed the material in a single layer, through a vibratory chute. You can then remove stainless steel wear particles, or paramagnetic particles from powder-dried raw materials, among others.
 
Metal separation
The LenaStar is a very advanced magnetic separation system, developed and produced by Goudsmit in collaboration with a Japanese partner. This advanced system removes ferromagnetic and paramagnetic metal particles from food ingredients and additives, chemicals and pigments. It can also remove stones, mud and insect excrement from dried granular products such as vegetables, fruits, soups, seeds, pasta, spices, nuts or tea. The paramagnetic properties of many soil types are the cause of the insect excrements - which mainly end up in herbs and tea - becoming magnetic.
 
Only this super strong LenaStar drum magnet is capable of demonstrating that food products are contaminated with undesirable particles of this type that the consumer ingests unknowingly.
 
Quality requirements
The stringent quality requirements in Japan make it necessary for companies there to adhere to the highest standards in precision detection. More than 50 leading producers of food products for the Japanese market (including Fuji Foods, Nissin Foods, House Foods Corporation (one of the largest spice producers in Japan), Twinnings, Unilever and Kellog's) have already chosen the LenaStar. This high Japanese quality standard is magnetic separator is now also available for you.
 
Characteristics

Fitted in a hygienic stainless steel housing that has flanges which can be mounted to a product channel
Simple operation, cleaning and maintenance
Completely cleanable with water and even steam (water-resistant version)
Product dust does not adhere to surface
Compact unit, easy to integrate into existing process


Types

Several dimensions and executions available

These 'LenaStar' pharma drum magnets in housing have an extra high-class hygienic design ánd they are equipped with a super strong 12,000 gauss magnetic drum. As a result, they filter even the smallest ferrous, weakly and even paramagnetic particles, such as: stones, mud, insect excrement, from your dried raw materials (eg tea, herbs).
 
Other types:

Our basic type drum magnets in housing are suitable for high capacity coarser raw materials like granules and fibres in the plastics and ceramics industries. The magnetic drum is only available in 3000 gauss magnetic strength, which is sufficient in most cases.
Our food type drum magnets in housing have a hygienic design to prevent against bacterial growth. Food type drum magnets are available by default in magnetic strengths 3000, 6000 and 9000 gauss. This enables them to filter larger to smaller ferrous and even weakly magnetic particles.


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of magnetic contaminants

A drum magnet continuously and fully automatically separates ferrous particles, such as iron, steel and stainless steel.
 
A drum magnet is a stationary (180°) magnet segment, with a stainless steel rotating drum. The magnet attracts magnetic particles that are in the product. The drum carries the attached particles with it to the bottom of the drum. There the particles drop off and can be collected and carried away. For strongly magnetic particles, carriers are placed on the drum to ‘push’ the particles out of the magnetic field.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the magnetic particles.

Product inlet size : 1600x250 mm
SETK-165-SD-B-30S2-NA-FZB-B-B
SKU: SRTK160054
Stock *: 0
Max. capacity: 300 m³/h
Product outlet size: 1730x275 mm
Fe-parts outlet size: 1730x150 mm
These magnetic drum separators are industrially finished. They remove 1-5 mm ferrous contaminants from all kinds of non-food powders and granulates. This basic type is equipped with a 3000 gauss strong magnetic drum.

For recycling or metal separation
Capacity up to 300 m³/h
Adjustable magnetic field
Continuous automatic cleaning
Ferriet/neodymium magnet (3000 gauss on shell)

Application

Non-food powders, granulates & fibres
Prevention of ferromagnetic contamination in your finished product.
Prevention of avoidable damage to machines (injection-moulding machines, extruders, mixers, grinders and other equipment).

Due to the continuous cleaning, the magnetic drum separator is very suitable for product flows with heavy magnetic particle contamination. You can use them in free-fall pipelines, or after a vibrating chute in belt conveyors.
 
These drum magnets are industrially finished. They remove 1-5 mm ferrous impurities from all kinds of non-food powders and granulates.

Types

Different types for different applications

These basic type magnetic drum separators in housing are suitable for high capacity coarser raw materials like granules and fibres in the plastics and ceramics industries. By default the magnetic drum is only available in 3000 gauss magnetic strength, which is sufficient in most cases.
 
Other types:

Our food type drum magnets in housing have a hygienic design to prevent against bacterial growth. Food type drum magnets are available by default in magnetic strengths 3000, 6000 and 9000 gauss. This enables them to filter larger to smaller ferrous and even weakly magnetic particles.
Our pharma type drum magnets in housing have an extra high class hygienic design AND they are executed with a 12,000 gauss drum. This enables them to even filter the smallest ferrous, weakly and even paramagnetic particles such as: stones, mud, insect excrement, etc. from your dried raw materials (e.g. tea, spices).


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering and disposal of magnetic impurities

These drum magnets continuously and fully automatically separate ferrous particles, such as iron and steel.
 
A drum magnet is a stationary (180°) magnet segment, with a stainless steel rotating drum. The magnet attracts magnetic particles that are in the product. The drum carries the attached particles with it to the bottom of the drum. There the particles drop off and can be collected and carried away. For strongly magnetic particles, carriers are placed on the drum to ‘push’ the separated ferrous particles out of the magnetic field for further discharging.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the magnetic particles.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the trapped magnetic particles.

Product inlet size : 1400x250 mm
SETK-145-SD-B-30S2-NA-FZB-B-B
SKU: SRTK140054
Stock *: 0
Max. capacity: 250 m³/h
Product outlet size: 1530x275 mm
Fe-parts outlet size: 1530x150 mm
These magnetic drum separators are industrially finished. They remove 1-5 mm ferrous contaminants from all kinds of non-food powders and granulates. This basic type is equipped with a 3000 gauss strong magnetic drum.

For recycling or metal separation
Capacity up to 300 m³/h
Adjustable magnetic field
Continuous automatic cleaning
Ferriet/neodymium magnet (3000 gauss on shell)

Application

Non-food powders, granulates & fibres
Prevention of ferromagnetic contamination in your finished product.
Prevention of avoidable damage to machines (injection-moulding machines, extruders, mixers, grinders and other equipment).

Due to the continuous cleaning, the magnetic drum separator is very suitable for product flows with heavy magnetic particle contamination. You can use them in free-fall pipelines, or after a vibrating chute in belt conveyors.
 
These drum magnets are industrially finished. They remove 1-5 mm ferrous impurities from all kinds of non-food powders and granulates.

Types

Different types for different applications

These basic type magnetic drum separators in housing are suitable for high capacity coarser raw materials like granules and fibres in the plastics and ceramics industries. By default the magnetic drum is only available in 3000 gauss magnetic strength, which is sufficient in most cases.
 
Other types:

Our food type drum magnets in housing have a hygienic design to prevent against bacterial growth. Food type drum magnets are available by default in magnetic strengths 3000, 6000 and 9000 gauss. This enables them to filter larger to smaller ferrous and even weakly magnetic particles.
Our pharma type drum magnets in housing have an extra high class hygienic design AND they are executed with a 12,000 gauss drum. This enables them to even filter the smallest ferrous, weakly and even paramagnetic particles such as: stones, mud, insect excrement, etc. from your dried raw materials (e.g. tea, spices).


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering and disposal of magnetic impurities

These drum magnets continuously and fully automatically separate ferrous particles, such as iron and steel.
 
A drum magnet is a stationary (180°) magnet segment, with a stainless steel rotating drum. The magnet attracts magnetic particles that are in the product. The drum carries the attached particles with it to the bottom of the drum. There the particles drop off and can be collected and carried away. For strongly magnetic particles, carriers are placed on the drum to ‘push’ the separated ferrous particles out of the magnetic field for further discharging.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the magnetic particles.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the trapped magnetic particles.

Product inlet size : 1200x250 mm
SETK-125-SD-B-30S2-NA-FZB-B-B
SKU: SRTK120054
Stock *: 0
Max. capacity: 215 m³/h
Product outlet size: 1330x275 mm
Fe-parts outlet size: 1330x150 mm
These magnetic drum separators are industrially finished. They remove 1-5 mm ferrous contaminants from all kinds of non-food powders and granulates. This basic type is equipped with a 3000 gauss strong magnetic drum.

For recycling or metal separation
Capacity up to 300 m³/h
Adjustable magnetic field
Continuous automatic cleaning
Ferriet/neodymium magnet (3000 gauss on shell)

Application

Non-food powders, granulates & fibres
Prevention of ferromagnetic contamination in your finished product.
Prevention of avoidable damage to machines (injection-moulding machines, extruders, mixers, grinders and other equipment).

Due to the continuous cleaning, the magnetic drum separator is very suitable for product flows with heavy magnetic particle contamination. You can use them in free-fall pipelines, or after a vibrating chute in belt conveyors.
 
These drum magnets are industrially finished. They remove 1-5 mm ferrous impurities from all kinds of non-food powders and granulates.

Types

Different types for different applications

These basic type magnetic drum separators in housing are suitable for high capacity coarser raw materials like granules and fibres in the plastics and ceramics industries. By default the magnetic drum is only available in 3000 gauss magnetic strength, which is sufficient in most cases.
 
Other types:

Our food type drum magnets in housing have a hygienic design to prevent against bacterial growth. Food type drum magnets are available by default in magnetic strengths 3000, 6000 and 9000 gauss. This enables them to filter larger to smaller ferrous and even weakly magnetic particles.
Our pharma type drum magnets in housing have an extra high class hygienic design AND they are executed with a 12,000 gauss drum. This enables them to even filter the smallest ferrous, weakly and even paramagnetic particles such as: stones, mud, insect excrement, etc. from your dried raw materials (e.g. tea, spices).


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering and disposal of magnetic impurities

These drum magnets continuously and fully automatically separate ferrous particles, such as iron and steel.
 
A drum magnet is a stationary (180°) magnet segment, with a stainless steel rotating drum. The magnet attracts magnetic particles that are in the product. The drum carries the attached particles with it to the bottom of the drum. There the particles drop off and can be collected and carried away. For strongly magnetic particles, carriers are placed on the drum to ‘push’ the separated ferrous particles out of the magnetic field for further discharging.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the magnetic particles.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the trapped magnetic particles.

Product inlet size : 1000x250 mm
SETK-105-SD-B-30S2-NA-FZB-B-B
SKU: SRTK100054
Stock *: 0
Max. capacity: 180 m³/h
Product outlet size: 1140x275 mm
Fe-parts outlet size: 1140x150 mm
These magnetic drum separators are industrially finished. They remove 1-5 mm ferrous contaminants from all kinds of non-food powders and granulates. This basic type is equipped with a 3000 gauss strong magnetic drum.

For recycling or metal separation
Capacity up to 300 m³/h
Adjustable magnetic field
Continuous automatic cleaning
Ferriet/neodymium magnet (3000 gauss on shell)

Application

Non-food powders, granulates & fibres
Prevention of ferromagnetic contamination in your finished product.
Prevention of avoidable damage to machines (injection-moulding machines, extruders, mixers, grinders and other equipment).

Due to the continuous cleaning, the magnetic drum separator is very suitable for product flows with heavy magnetic particle contamination. You can use them in free-fall pipelines, or after a vibrating chute in belt conveyors.
 
These drum magnets are industrially finished. They remove 1-5 mm ferrous impurities from all kinds of non-food powders and granulates.

Types

Different types for different applications

These basic type magnetic drum separators in housing are suitable for high capacity coarser raw materials like granules and fibres in the plastics and ceramics industries. By default the magnetic drum is only available in 3000 gauss magnetic strength, which is sufficient in most cases.
 
Other types:

Our food type drum magnets in housing have a hygienic design to prevent against bacterial growth. Food type drum magnets are available by default in magnetic strengths 3000, 6000 and 9000 gauss. This enables them to filter larger to smaller ferrous and even weakly magnetic particles.
Our pharma type drum magnets in housing have an extra high class hygienic design AND they are executed with a 12,000 gauss drum. This enables them to even filter the smallest ferrous, weakly and even paramagnetic particles such as: stones, mud, insect excrement, etc. from your dried raw materials (e.g. tea, spices).


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering and disposal of magnetic impurities

These drum magnets continuously and fully automatically separate ferrous particles, such as iron and steel.
 
A drum magnet is a stationary (180°) magnet segment, with a stainless steel rotating drum. The magnet attracts magnetic particles that are in the product. The drum carries the attached particles with it to the bottom of the drum. There the particles drop off and can be collected and carried away. For strongly magnetic particles, carriers are placed on the drum to ‘push’ the separated ferrous particles out of the magnetic field for further discharging.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the magnetic particles.
 
The advantage of a drum magnet is that it is a continuous cleaning/separating system, in which it is not necessary to stop the product flow to remove the trapped magnetic particles.

Belt type : 1.3 mm Polyurethane antistatic, blue, with 1 cleat (A-shaped)
BELT PU 1.3MM RHFH600 2544x817
SKU: 45.1800100
Stock *: 0
Suitable for belt width: 600 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Belt type : 2.4 mm Polyurethane, white, 94° Shore
RECC-CB-15-PU-24
SKU: E0118594
Stock *: 0
Suitable for belt width: 1500 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Belt type : 6.5 mm Rubber, black
RECC-CB-20-NBR-65
SKU: E0129536
Stock *: 0
Suitable for belt width: 2000 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime