Rubber-metal buffer MGP diameter 20mm height 8mm thread M6x18
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, 55° Shore hardness.

Rubber-Metal buffers are simple, reasonably priced standard components
used for elastic mounting. When shearing load occurs their load-bearing
capacity is considerably lower than with pressure load. This has to be
considered when horizontal mass forces or belt traction occur. The grade
of rubber used has perfect physical properties. Temperature resistant up
to 80°C. For a linear resilience characteristic the Spring Load C means,
for any operating point, the constant relation of load F [N] to jounce
travel f [mm]. C = F/f [N/mm]. In the technical data, these constants
are stated as CD for pure pressure load and as CS for pure shear load. *
F perm. is the permissible static permanent load, which may be overlaid
by a dynamic, alternating load. With shearing load please take care that
no tension load in the rubber occurs at all during mounting. To achieve
a sufficient fatigue strength provide some compressive prestressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be accordingly reduced.

Article ID: 68530100

Rubber-metal buffer MGP diameter 15mm height 8mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, 55° Shore hardness.

Rubber-Metal buffers are simple, reasonably priced standard components
used for elastic mounting. When shearing load occurs their load-bearing
capacity is considerably lower than with pressure load. This has to be
considered when horizontal mass forces or belt traction occur. The grade
of rubber used has perfect physical properties. Temperature resistant up
to 80°C. For a linear resilience characteristic the Spring Load C means,
for any operating point, the constant relation of load F [N] to jounce
travel f [mm]. C = F/f [N/mm]. In the technical data, these constants
are stated as CD for pure pressure load and as CS for pure shear load. *
F perm. is the permissible static permanent load, which may be overlaid
by a dynamic, alternating load. With shearing load please take care that
no tension load in the rubber occurs at all during mounting. To achieve
a sufficient fatigue strength provide some compressive prestressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be accordingly reduced.

Article ID: 68528700

Rubber-metal buffer MGP diameter 15mm height 7mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, 55° Shore hardness.

Rubber-Metal buffers are simple, reasonably priced standard components
used for elastic mounting. When shearing load occurs their load-bearing
capacity is considerably lower than with pressure load. This has to be
considered when horizontal mass forces or belt traction occur. The grade
of rubber used has perfect physical properties. Temperature resistant up
to 80°C. For a linear resilience characteristic the Spring Load C means,
for any operating point, the constant relation of load F [N] to jounce
travel f [mm]. C = F/f [N/mm]. In the technical data, these constants
are stated as CD for pure pressure load and as CS for pure shear load. *
F perm. is the permissible static permanent load, which may be overlaid
by a dynamic, alternating load. With shearing load please take care that
no tension load in the rubber occurs at all during mounting. To achieve
a sufficient fatigue strength provide some compressive prestressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be accordingly reduced.

Article ID: 68528600

Rubber-metal MGS diameter 20mm height 8mm thread M6x18
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, hardness 55° Shore.

Metal on one side only. Metal bumpers can be used to limit bearing
surfaces e.g. for elastically mounted power units, and as bump stop to
limit the spring travel in vehicles. They can also be used for machines
that cannot be fixed to the floor or are standing on floors with an
easily damaged surface, e.g. office machines. * Fperm. is the
permissible static permanent load, which may be overlaid by a dynamic,
alternating load. With shearing load please take care that no tension
load in the rubber occurs at all during mounting. To achieve a
sufficient fatigue strength provide some compressive pre-stressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be reduced accordingly. Temperature resistant up to 80°C.

Article ID: 68580100

Rubber-metal buffer MGP diameter 10mm height 10mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, 55° Shore hardness.

Rubber-Metal buffers are simple, reasonably priced standard components
used for elastic mounting. When shearing load occurs their load-bearing
capacity is considerably lower than with pressure load. This has to be
considered when horizontal mass forces or belt traction occur. The grade
of rubber used has perfect physical properties. Temperature resistant up
to 80°C. For a linear resilience characteristic the Spring Load C means,
for any operating point, the constant relation of load F [N] to jounce
travel f [mm]. C = F/f [N/mm]. In the technical data, these constants
are stated as CD for pure pressure load and as CS for pure shear load. *
F perm. is the permissible static permanent load, which may be overlaid
by a dynamic, alternating load. With shearing load please take care that
no tension load in the rubber occurs at all during mounting. To achieve
a sufficient fatigue strength provide some compressive prestressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be accordingly reduced.

Article ID: 68528100

Rubber-metal buffer MGP diameter 8mm height 8mm thread M3x6
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, 55° Shore hardness.

Rubber-Metal buffers are simple, reasonably priced standard components
used for elastic mounting. When shearing load occurs their load-bearing
capacity is considerably lower than with pressure load. This has to be
considered when horizontal mass forces or belt traction occur. The grade
of rubber used has perfect physical properties. Temperature resistant up
to 80°C. For a linear resilience characteristic the Spring Load C means,
for any operating point, the constant relation of load F [N] to jounce
travel f [mm]. C = F/f [N/mm]. In the technical data, these constants
are stated as CD for pure pressure load and as CS for pure shear load. *
F perm. is the permissible static permanent load, which may be overlaid
by a dynamic, alternating load. With shearing load please take care that
no tension load in the rubber occurs at all during mounting. To achieve
a sufficient fatigue strength provide some compressive prestressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be accordingly reduced.

Article ID: 68528000

Grub screw DIN 6332 with thrust point type SK with internal hexagon thread M8 length 60mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, burnished. Type SK: With internal hexagon. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65401101

Rubber-metal MGS diameter 20mm height 5mm thread M6x18
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, hardness 55° Shore.

Metal on one side only. Metal bumpers can be used to limit bearing
surfaces e.g. for elastically mounted power units, and as bump stop to
limit the spring travel in vehicles. They can also be used for machines
that cannot be fixed to the floor or are standing on floors with an
easily damaged surface, e.g. office machines. * Fperm. is the
permissible static permanent load, which may be overlaid by a dynamic,
alternating load. With shearing load please take care that no tension
load in the rubber occurs at all during mounting. To achieve a
sufficient fatigue strength provide some compressive pre-stressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be reduced accordingly. Temperature resistant up to 80°C.

Article ID: 68579100

Rubber-metal MGS diameter 15mm height 15mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, hardness 55° Shore.

Metal on one side only. Metal bumpers can be used to limit bearing
surfaces e.g. for elastically mounted power units, and as bump stop to
limit the spring travel in vehicles. They can also be used for machines
that cannot be fixed to the floor or are standing on floors with an
easily damaged surface, e.g. office machines. * Fperm. is the
permissible static permanent load, which may be overlaid by a dynamic,
alternating load. With shearing load please take care that no tension
load in the rubber occurs at all during mounting. To achieve a
sufficient fatigue strength provide some compressive pre-stressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be reduced accordingly. Temperature resistant up to 80°C.

Article ID: 68579000

Rubber-metal MGS diameter 15mm height 10mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, hardness 55° Shore.

Metal on one side only. Metal bumpers can be used to limit bearing
surfaces e.g. for elastically mounted power units, and as bump stop to
limit the spring travel in vehicles. They can also be used for machines
that cannot be fixed to the floor or are standing on floors with an
easily damaged surface, e.g. office machines. * Fperm. is the
permissible static permanent load, which may be overlaid by a dynamic,
alternating load. With shearing load please take care that no tension
load in the rubber occurs at all during mounting. To achieve a
sufficient fatigue strength provide some compressive pre-stressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be reduced accordingly. Temperature resistant up to 80°C.

Article ID: 68578800

Rubber-metal MGS diameter 15mm height 8mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, hardness 55° Shore.

Metal on one side only. Metal bumpers can be used to limit bearing
surfaces e.g. for elastically mounted power units, and as bump stop to
limit the spring travel in vehicles. They can also be used for machines
that cannot be fixed to the floor or are standing on floors with an
easily damaged surface, e.g. office machines. * Fperm. is the
permissible static permanent load, which may be overlaid by a dynamic,
alternating load. With shearing load please take care that no tension
load in the rubber occurs at all during mounting. To achieve a
sufficient fatigue strength provide some compressive pre-stressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be reduced accordingly. Temperature resistant up to 80°C.

Article ID: 68578700

Rubber-metal MGS diameter 15mm height 7mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, hardness 55° Shore.

Metal on one side only. Metal bumpers can be used to limit bearing
surfaces e.g. for elastically mounted power units, and as bump stop to
limit the spring travel in vehicles. They can also be used for machines
that cannot be fixed to the floor or are standing on floors with an
easily damaged surface, e.g. office machines. * Fperm. is the
permissible static permanent load, which may be overlaid by a dynamic,
alternating load. With shearing load please take care that no tension
load in the rubber occurs at all during mounting. To achieve a
sufficient fatigue strength provide some compressive pre-stressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be reduced accordingly. Temperature resistant up to 80°C.

Article ID: 68578600

Lock nut for miniature shock absorber thread M12x1
Material: Steel burnished

Article ID: 69003504

Grub screw DIN 6332 with thrust point thread M8 length 60mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, black oxide finish. Type S: With slot. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65401100

Rubber-metal MGS diameter 10mm height 10mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, hardness 55° Shore.

Metal on one side only. Metal bumpers can be used to limit bearing
surfaces e.g. for elastically mounted power units, and as bump stop to
limit the spring travel in vehicles. They can also be used for machines
that cannot be fixed to the floor or are standing on floors with an
easily damaged surface, e.g. office machines. * Fperm. is the
permissible static permanent load, which may be overlaid by a dynamic,
alternating load. With shearing load please take care that no tension
load in the rubber occurs at all during mounting. To achieve a
sufficient fatigue strength provide some compressive pre-stressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be reduced accordingly. Temperature resistant up to 80°C.

Article ID: 68578100

Rubber-metal buffer MGP diameter 15mm height 20mm thread M4x13
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, 55° Shore hardness.

Rubber-Metal buffers are simple, reasonably priced standard components
used for elastic mounting. When shearing load occurs their load-bearing
capacity is considerably lower than with pressure load. This has to be
considered when horizontal mass forces or belt traction occur. The grade
of rubber used has perfect physical properties. Temperature resistant up
to 80°C. For a linear resilience characteristic the Spring Load C means,
for any operating point, the constant relation of load F [N] to jounce
travel f [mm]. C = F/f [N/mm]. In the technical data, these constants
are stated as CD for pure pressure load and as CS for pure shear load. *
F perm. is the permissible static permanent load, which may be overlaid
by a dynamic, alternating load. With shearing load please take care that
no tension load in the rubber occurs at all during mounting. To achieve
a sufficient fatigue strength provide some compressive prestressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be accordingly reduced.

Article ID: 68528900

Rubber-metal buffer MGP diameter 15mm height 10mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, 55° Shore hardness.

Rubber-Metal buffers are simple, reasonably priced standard components
used for elastic mounting. When shearing load occurs their load-bearing
capacity is considerably lower than with pressure load. This has to be
considered when horizontal mass forces or belt traction occur. The grade
of rubber used has perfect physical properties. Temperature resistant up
to 80°C. For a linear resilience characteristic the Spring Load C means,
for any operating point, the constant relation of load F [N] to jounce
travel f [mm]. C = F/f [N/mm]. In the technical data, these constants
are stated as CD for pure pressure load and as CS for pure shear load. *
F perm. is the permissible static permanent load, which may be overlaid
by a dynamic, alternating load. With shearing load please take care that
no tension load in the rubber occurs at all during mounting. To achieve
a sufficient fatigue strength provide some compressive prestressing. The
stated permissible loads are only approximate, guideline values for the
static load for "medium" rubber hardness. With particularly high,
dynamic, alternating loads or high frequencies, the load figures have to
be accordingly reduced.

Article ID: 68528800

Rubber-metal MGA diameter 10mm height 10mm thread M4x10
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, Rubber hardness Shore A medium: about 55°.

* Fperm. is the permissible static permanent load, which may
be overlaid by a dynamic, alternating load. With shearing load please
take care that no tension load in the rubber occurs at all during
mounting. To achieve a sufficient fatigue strength provide some
compressive pre-stressing. The stated permissible loads are only
approximate, guideline values for the static load for "medium" rubber
hardness. With particularly high, dynamic, alternating loads or high
frequencies, the load figures have to be reduced accordingly.
Temperature resistant up to 80°C.

Article ID: 68558100

Rubber-metal MGA diameter 8mm height 8mm thread M3x6
Material: Metal parts: Steel, zinc-plated. Elastomer: Natural
rubber, Rubber hardness Shore A medium: about 55°.

* Fperm. is the permissible static permanent load, which may
be overlaid by a dynamic, alternating load. With shearing load please
take care that no tension load in the rubber occurs at all during
mounting. To achieve a sufficient fatigue strength provide some
compressive pre-stressing. The stated permissible loads are only
approximate, guideline values for the static load for "medium" rubber
hardness. With particularly high, dynamic, alternating loads or high
frequencies, the load figures have to be reduced accordingly.
Temperature resistant up to 80°C.

Article ID: 68558000

Rubber-metal buffer MGI with internal thread on both sides diameter 20mm height 25mm thread M6x6
Material: Elastomer: Natural rubber hardness 55°. Metal parts:
Steel, zinc-plated.

Both sides with internal thread. Standard components for elastic
mounting. The grade of rubber used has perfect physical properties.

Temperature resistant up to 80ºC.

Other sizes, Shore hardnesses or elastomer types on request.

* Fperm. is the permissible static permanent load, which may
be overlaid by a dynamic, alternating load. With shearing load please
take care that no tension load in the rubber occurs at all during
mounting. To achieve a sufficient fatigue strength provide some
compressive prestressing.

Article ID: 68542000

Grub screw DIN 6332 with thrust point type SK with internal hexagon thread M8 length 40mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, burnished. Type SK: With internal hexagon. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400901

Lock nut for miniature shock absorber thread M10x1
Material: Steel burnished

Article ID: 69005004

Lock nut for miniature shock absorber thread M8x1
Material: Steel burnished

Article ID: 69003004

Rubber-metal buffer MGI with internal thread on both sides diameter 10mm height 15mm thread M4x4
Material: Elastomer: Natural rubber hardness 55°. Metal parts:
Steel, zinc-plated.

Both sides with internal thread. Standard components for elastic
mounting. The grade of rubber used has perfect physical properties.

Temperature resistant up to 80ºC.

Other sizes, Shore hardnesses or elastomer types on request.

* Fperm. is the permissible static permanent load, which may
be overlaid by a dynamic, alternating load. With shearing load please
take care that no tension load in the rubber occurs at all during
mounting. To achieve a sufficient fatigue strength provide some
compressive prestressing.

Article ID: 68541015

Grub screw DIN 6332 with thrust point type SK with internal hexagon thread M6 length 50mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, burnished. Type SK: With internal hexagon. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400701

Rubber-metal buffer MGI with internal thread on both sides diameter 15mm height 15mm thread M4x5
Material: Elastomer: Natural rubber hardness 55°. Metal parts:
Steel, zinc-plated.

Both sides with internal thread. Standard components for elastic
mounting. The grade of rubber used has perfect physical properties.

Temperature resistant up to 80ºC.

Other sizes, Shore hardnesses or elastomer types on request.

* Fperm. is the permissible static permanent load, which may
be overlaid by a dynamic, alternating load. With shearing load please
take care that no tension load in the rubber occurs at all during
mounting. To achieve a sufficient fatigue strength provide some
compressive prestressing.

Article ID: 68541500

Grub screw DIN 6332 with thrust point thread M8 length 40mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, black oxide finish. Type S: With slot. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400900

Rubber-metal buffer MGH stainless steel diameter 35mm height 15mm bore 8,4mm (for screw M8)
Material: Elastomer: Rubber NBR, black, hardness 55º Shore A. Metal part: Stainless steel 1.4301.Hollow design. One side metal, with mounting bore for allen screw DIN 912.Due to the hollow design, these elements are particularly suitable as end stops. Also usable as elastic machine feet.The grade of rubber has perfect physical properties.Temperature resistant up to +100ºC (for short time +120°C).Other sizes, Shore hardnesses or elastomer types on request.* Permissible Pressure Load.
Article ID: 68921350

Rubber-metal buffer MGI with internal thread on both sides diameter 10mm height 10mm thread M4x4
Material: Elastomer: Natural rubber hardness 55°. Metal parts:
Steel, zinc-plated.

Both sides with internal thread. Standard components for elastic
mounting. The grade of rubber used has perfect physical properties.

Temperature resistant up to 80ºC.

Other sizes, Shore hardnesses or elastomer types on request.

* Fperm. is the permissible static permanent load, which may
be overlaid by a dynamic, alternating load. With shearing load please
take care that no tension load in the rubber occurs at all during
mounting. To achieve a sufficient fatigue strength provide some
compressive prestressing.

Article ID: 68541000

Grub screw DIN 6332 with thrust point thread M6 length 50mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, black oxide finish. Type S: With slot. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400700

Grub screw DIN 6332 with thrust point type SK with internal hexagon thread M6 length 30mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, burnished. Type SK: With internal hexagon. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400601

Grub screw DIN 6332 with thrust point thread M6 length 30mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, black oxide finish. Type S: With slot. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400600

Rubber-metal buffer MGH stainless steel diameter 25mm height 12mm bore 6,4mm (for screw M6)
Material: Elastomer: Rubber NBR, black, hardness 55º Shore A. Metal part: Stainless steel 1.4301.Hollow design. One side metal, with mounting bore for allen screw DIN 912.Due to the hollow design, these elements are particularly suitable as end stops. Also usable as elastic machine feet.The grade of rubber has perfect physical properties.Temperature resistant up to +100ºC (for short time +120°C).Other sizes, Shore hardnesses or elastomer types on request.* Permissible Pressure Load.
Article ID: 68921250

Rubber-metal buffer MGH stainless steel diameter 20mm height 10mm bore 5,3mm (for screw M5)
Material: Elastomer: Rubber NBR, black, hardness 55º Shore A. Metal part: Stainless steel 1.4301.Hollow design. One side metal, with mounting bore for allen screw DIN 912.Due to the hollow design, these elements are particularly suitable as end stops. Also usable as elastic machine feet.The grade of rubber has perfect physical properties.Temperature resistant up to +100ºC (for short time +120°C).Other sizes, Shore hardnesses or elastomer types on request.* Permissible Pressure Load.
Article ID: 68921200

Rubber-metal buffer MGH stainless steel diameter 15mm height 8mm bore 4,3mm (for screw M4)
Material: Elastomer: Rubber NBR, black, hardness 55º Shore A. Metal part: Stainless steel 1.4301.Hollow design. One side metal, with mounting bore for allen screw DIN 912.Due to the hollow design, these elements are particularly suitable as end stops. Also usable as elastic machine feet.The grade of rubber has perfect physical properties.Temperature resistant up to +100ºC (for short time +120°C).Other sizes, Shore hardnesses or elastomer types on request.* Permissible Pressure Load.
Article ID: 68921150