Suitable for belt width : 400 mm
RHP-B204A06-040-RSD-BA
SKU: RHAN20040000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Belt type : 3 mm Polyurethane, green, 94° Shore
RECE-CB-15-X-PU-30
SKU: 45.1800047
Stock: 4
Suitable for belt width: 1500 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Length : 626 mm
SVM-F-470x207-0626-F-F0E
SKU: RBPF020600
Stock: 6
Advised max. installation height: 125-230 mm
Height: 208 mm
Removal of pieces of steel in the recycling industry or for protection of grinding mills. For installation up to 400 mm above conveyor belt.

Max. installation height 400 mm
Capture Fe particles from 1 mm
Various dimensions and flange types
For belt width 400-1600 mm
Easy to install

Application

Application

Permanent ferrite suspended magnets (block magnets) consume no energy, which is one of the factors that makes them so price effective. These magnets remove ferromagnetic (Fe) particles as small as 0.5 mm (depending on the layer thickness on the belt).

Cleaning

Cleaning

Cleaning of the block magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning), by swinging the extractor plate away from the magnet; the Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field.

Placement

Placement

A block magnet is hung above a conveyor belt, by means of chains or cables. The addition of these magnets can considerably boost separation yield:
 
Placement over pulley: In this configuration the magnet hangs at an angle over the end of the conveyor belt, where discharge of the material occurs. This is the ideal situation, because the bulk flow is ‘broken open’ at this point. When this happens, the iron particles are exposed within the surrounding material. This allows them to be more easily drawn to the magnet. Keep in mind, however, that it is important for the construction directly beneath the magnet to be made of non-magnetic material; otherwise it, too, will become magnetized.
 
Placement over band: This position is used for small layer thickness (or mono-layers). Or when there is no other option due to the potential for magnetization of underlying steel components (such as motors or guide rollers).

Working principle

Working principle

Suspended magnets (block magnets) remove undesirable ferromagnetic (Fe) particles such as iron and steel from material flows containing relatively little Fe contamination. They are placed above flat or trough-shaped conveyor belts. The metal particles are drawn out of the raw material flow and held by the magnet. This results in a pure iron fraction suitable for immediate reuse (recycling).
 
They are used to check incoming product flows and for the protection of machines, such as shredders and sieves. When heavy metal contamination is present, it is better to use an overbelt magnet; this type continuously carries away the iron particles.

Suitable for belt width : 500 mm
RHP-B168A06-050-FSD-BA
SKU: RHAN16050000
Stock *: 0
Diameter: 168.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 650 mm
RHP-F219A06-065-RSD-BA
SKU: RHAF22065000
Stock *: 0
Diameter: 219 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Size : 350 mm
SMR-N-0350x350x40-07E-S6-S
SKU: SEMR353538
Stock *: 0
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 7
Weight: 11 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.

Magnet rotor cleaning unit SECR2020/3030 | Polished
EXTR. CLEANER CR2020/3030 F5m
SKU: E0106233
Stock *: 0
Surface treatment/finishing: S5: Polished, Ra 0,4 µm, excluding welds and end faces
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Suitable for belt width : 650 mm
RHP-F204A06-065-FSD-BA
SKU: RHAF20065000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 600 mm
RHP-F219A06-060-RSD-BA
SKU: RHAF22060000
Stock *: 0
Diameter: 219 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 600 mm
RHP-F204A06-060-FSD-BA
SKU: RHAF20060000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Length : 560 mm
SVM-N-158x32-0500-F-F1M
SKU: SVMN030500
Stock *: 0
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Suitable for belt width : 650 mm
RHP-B114A06-065-RSD-BA
SKU: RHAN1106500
Stock *: 0
Diameter: 114.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Type : 3-Axis VGM
GAUSSMETER 3 AXIS VGM
SKU: 65.0000067
Stock: 7
With a gauss meter, you measure locally - on the surface - the magnetic flux density in units of tesla, gauss, Ka/m or oersted. Flux density is a measure of the amount of magnetic flux through a surface. Goudsmit also conducts magnetic measurements on site if desired.

Measures strength of magnetic field
Deliverable from stock
Readout in various units
Accurate
Various functions

Operation

Operation

Gauss meter measurements use the Hall effect as the measuring principle. The sensor captures the magnetic flux density that is perpendicular to the sensor plane. The magnetic field generates an output voltage on the sensor, which is proportional to the product of the magnetic field strength and the induced current.


1D gauss meter

Type HG09: Basic version - 1D gauss meter

For measurement on a surface. The basic version is a one-dimensional meter (1D) equipped with a single Hall sensor which measures the flux density in one direction.   Suitable for: accurately measuring flux densities in one direction with a large range (max. 4.5 T) both static and alternating fields and pulses thanks to a thin measuring probe, measurements very close to the surface and in crevices measurements of fields where the local field orientation is known. This gauss meter is used to measure peak flux density of permanent and electromagnetic systems for inspections.


3D gauss meter

Type 3 Axis VGM: 3D gauss meter

The 3D meter allows you to measure magnetic fields in a free space. This gauss meter is equipped with three Hall sensors, which measure the flux density in three directions (x, y and z).   Suitable for: measuring relatively low flux densities in three directions and the ensuing results - up to max. 80 mT; scanning magnetic fields with a set alarm level. Application examples: determining safe distances in connection with exposure to static magnetic fields (medical implants, projectile hazards, pregnant workers); measuring residual magnetism in products, for example before and after demagnetizing; determining local field orientation of magnetic fields.

Suitable for belt width : 500 mm
RHP-F219A06-050-RSD-BA
SKU: RHAF22050000
Stock *: 0
Diameter: 219 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 500 mm
RHP-F204A06-050-FSD-BA
SKU: RHAF20050000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 400 mm
RHP-B168A06-040-FSD-BA
SKU: RHAN16040000
Stock *: 0
Diameter: 168.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Length : 1000 mm
SVM-F-304x99-1000-B-F0E
SKU: SVMF051000
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Diameter : 265 mm
SMR-N-D250x50-05E-S4-S
SKU: SEMR025078
Stock: 15
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 5
Weight: 4.4 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.

Suitable for belt width : 600 mm
RHP-B114A06-060-RSD-BA
SKU: RHAN1106000
Stock *: 0
Diameter: 114.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Suitable for belt width : 400 mm
RHP-F204A06-040-FSD-BA
SKU: RHAF20040000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Length : 460 mm
SVM-N-158x32-0400-F-F1M
SKU: SVMN030400
Stock *: 0
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Length : 500 mm
SVM-N-204x55-0500-B-F1M
SKU: SVMN020500
Stock *: 0
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Suitable for belt width : 500 mm
RHP-B114A06-050-RSD-BA
SKU: RHAN1105000
Stock *: 0
Diameter: 114.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Length : 1400 mm
SVM-F-204x92-1400-B-F0E
SKU: SVMF041400
Stock *: 0
Type: VMF4
Advised max. installation height: 70-110 mm
Interface/connection dim's: Threaded hole M8 (8x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Size : 300 mm
SMR-N-0300x300x40-06E-S6-S
SKU: SEMR303038
Stock *: 0
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 6
Weight: 8.5 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.

Length : 900 mm
SVM-F-304x99-0900-B-F0E
SKU: SVMF050900
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Set counter flanges + O-rings Hydrohansu Ø250 mm | Hygienic
SET HYDROFORM CONTRA FLANGES/O
SKU: E0103986
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Belt type : 3 mm Polyurethane, green, 94° Shore
RECE-CB-10-X-PU-30
SKU: 45.1800041
Stock: 1
Suitable for belt width: 1000 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Extension cable 100 m
DEMAG EXTENSION CABLE 100m
SKU: E0068570
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Length : 410 mm
SVM-N-158x32-0350-F-F1M
SKU: SVMN030350
Stock *: 0
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Diameter : 215 mm
SMR-N-D200x50-04E-S4-S
SKU: SEMR020078
Stock: 3
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 4
Weight: 2.8 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.

Length : 426 mm
PLATE MAGN FXD 470x207 L=426
SKU: RBPF020400
Stock *: 0
Advised max. installation height: 125-230 mm
Height: 208 mm
Removal of pieces of steel in the recycling industry or for protection of grinding mills. For installation up to 400 mm above conveyor belt.

Max. installation height 400 mm
Capture Fe particles from 1 mm
Various dimensions and flange types
For belt width 400-1600 mm
Easy to install

Application

Application

Permanent ferrite suspended magnets (block magnets) consume no energy, which is one of the factors that makes them so price effective. These magnets remove ferromagnetic (Fe) particles as small as 0.5 mm (depending on the layer thickness on the belt).

Cleaning

Cleaning

Cleaning of the block magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning), by swinging the extractor plate away from the magnet; the Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field.

Placement

Placement

A block magnet is hung above a conveyor belt, by means of chains or cables. The addition of these magnets can considerably boost separation yield:
 
Placement over pulley: In this configuration the magnet hangs at an angle over the end of the conveyor belt, where discharge of the material occurs. This is the ideal situation, because the bulk flow is ‘broken open’ at this point. When this happens, the iron particles are exposed within the surrounding material. This allows them to be more easily drawn to the magnet. Keep in mind, however, that it is important for the construction directly beneath the magnet to be made of non-magnetic material; otherwise it, too, will become magnetized.
 
Placement over band: This position is used for small layer thickness (or mono-layers). Or when there is no other option due to the potential for magnetization of underlying steel components (such as motors or guide rollers).

Working principle

Working principle

Suspended magnets (block magnets) remove undesirable ferromagnetic (Fe) particles such as iron and steel from material flows containing relatively little Fe contamination. They are placed above flat or trough-shaped conveyor belts. The metal particles are drawn out of the raw material flow and held by the magnet. This results in a pure iron fraction suitable for immediate reuse (recycling).
 
They are used to check incoming product flows and for the protection of machines, such as shredders and sieves. When heavy metal contamination is present, it is better to use an overbelt magnet; this type continuously carries away the iron particles.

Magnet rotor cleaning unit SECR2020/3030
EXTR. CLEANER CR2020/3030 F1m
SKU: E0102869
Stock: 1
Surface treatment/finishing: S1: Grit blasted, Ra 3 µm
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Suitable for belt width : 300 mm
RHP-B168A06-030-FSD-BA
SKU: RHAN16030000
Stock *: 0
Diameter: 168.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Length : 1250 mm
SVM-F-204x92-1250-B-F0E
SKU: SVMF041250
Stock *: 0
Type: VMF4
Advised max. installation height: 70-110 mm
Interface/connection dim's: Threaded hole M8 (8x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Belt type : 6.5 mm Rubber, black
RECC-CB-15-NBR-65
SKU: E0067603
Stock *: 0
Suitable for belt width: 1500 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Length : 800 mm
SVM-F-304x99-0800-B-F0E
SKU: SVMF050800
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Length : 400 mm
SVM-N-204x55-0400-B-F1M
SKU: SVMN020400
Stock *: 0
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Length : 360 mm
SVM-N-158x32-0300-F-F1M
SKU: SVMN030300
Stock: 3
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Suitable for belt width : 400 mm
RHP-B114A06-040-RSD-BA
SKU: RHAN11040000
Stock *: 0
Diameter: 114.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Magnet width : 920 mm
MAGNETIC SWEEPER W920 RMS3
SKU: SEMV092020
Stock *: 0
Type: RMS3 - manually operated
Magnetic system: Permanent ferrite magnet
Magnetic brooms sweep up iron and steel parts from clean or rough floors or sandy surfaces. In short, in places where iron is not or very difficult to sweep together or is not visible, such as in sand.The brooms collect metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds. Fast and easy cleanable.

Push manually or tow as a trailer
Permanent magnet
Magnet width 300-1600 mm
Quick cleaning through use of extractor plates
Engineering, production & service

Application

Sweeping floors to clean them from iron particles

Magnetic brooms (magnetic sweepers) 'sweep up' iron particles from clean or rough floors or sandy surfaces. They work well in areas where it is very difficult to sweep up iron (or just the iron and nothing else) or it is not visible, such as in sand.
 
The strong magnet in the broom collects metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds.

Types

We have standard types and 'specials' available

In addition to the standard magnetic brooms on this page, we are happy to make a special broom for you on request. Other dimensions or attachments for forklift forks or trailers, etc.

Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Cleaning (iron disposal)

Cleaning & discharging of caught iron particles

Bar magnet type
The bar magnet has a scraper ring, with which you can slide the captured iron particles to the side. There the iron automatically falls from the bar housing.
 
Plate magnet type
This type of magnetic broom contains a strong plate magnet with a hinged separator plate (extractor plate) in front. After the floor has been swept the separation plate can be swung away, causing the iron particles to automatically fall off. It can then easily be swept up with a dustpan and broom.

Length : 1100 mm
SVM-F-204x92-1100-B-F0E
SKU: SVMF041100
Stock *: 0
Type: VMF4
Advised max. installation height: 70-110 mm
Interface/connection dim's: Threaded hole M8 (8x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Length : 700 mm
SVM-F-304x99-0700-B-F0E
SKU: SVMF050700
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Size : 250 mm
SMR-N-0250x250x40-05E-S6-S
SKU: SEMR252538
Stock: 10
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 5
Weight: 6.2 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.

Length : 350 mm
SVM-N-204x55-0350-B-F1M
SKU: SVMN020350
Stock *: 0
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Diameter : 165 mm
SMR-N-D150x50-03E-S4-S
SKU: SEMR015078
Stock: 15
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 3
Weight: 1.9 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.

Length : 1000 mm
SVM-F-204x92-1000-B-F0E
SKU: SVMF041000
Stock *: 0
Advised max. installation height: 70-110 mm
Height: 92 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Length : 310 mm
SVM-N-158x32-0250-F-F1M
SKU: SVMN030250
Stock: 2
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Type : HG09
GAUSSMETER HGM09
SKU: 65.0000047
Stock: 7
With a gauss meter, you measure locally - on the surface - the magnetic flux density in units of tesla, gauss, Ka/m or oersted. Flux density is a measure of the amount of magnetic flux through a surface. Goudsmit also conducts magnetic measurements on site if desired.

Measures strength of magnetic field
Deliverable from stock
Readout in various units
Accurate
Various functions

Operation

Operation

Gauss meter measurements use the Hall effect as the measuring principle. The sensor captures the magnetic flux density that is perpendicular to the sensor plane. The magnetic field generates an output voltage on the sensor, which is proportional to the product of the magnetic field strength and the induced current.


1D gauss meter

Type HG09: Basic version - 1D gauss meter

For measurement on a surface. The basic version is a one-dimensional meter (1D) equipped with a single Hall sensor which measures the flux density in one direction.   Suitable for: accurately measuring flux densities in one direction with a large range (max. 4.5 T) both static and alternating fields and pulses thanks to a thin measuring probe, measurements very close to the surface and in crevices measurements of fields where the local field orientation is known. This gauss meter is used to measure peak flux density of permanent and electromagnetic systems for inspections.


3D gauss meter

Type 3 Axis VGM: 3D gauss meter

The 3D meter allows you to measure magnetic fields in a free space. This gauss meter is equipped with three Hall sensors, which measure the flux density in three directions (x, y and z).   Suitable for: measuring relatively low flux densities in three directions and the ensuing results - up to max. 80 mT; scanning magnetic fields with a set alarm level. Application examples: determining safe distances in connection with exposure to static magnetic fields (medical implants, projectile hazards, pregnant workers); measuring residual magnetism in products, for example before and after demagnetizing; determining local field orientation of magnetic fields.

Belt type : 3 mm PVC, black
RECE-CB-15-X-PVC-30
SKU: E0094039
Stock *: 0
Suitable for belt width: 1500 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Magnet width : 620 mm
MAGNETIC SWEEPER W620 RMS2
SKU: SEMV062020
Stock *: 0
Type: RMS2 - manually operated
Magnetic system: Permanent ferrite magnet
Magnetic brooms sweep up iron and steel parts from clean or rough floors or sandy surfaces. In short, in places where iron is not or very difficult to sweep together or is not visible, such as in sand.The brooms collect metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds. Fast and easy cleanable.

Push manually or tow as a trailer
Permanent magnet
Magnet width 300-1600 mm
Quick cleaning through use of extractor plates
Engineering, production & service

Application

Sweeping floors to clean them from iron particles

Magnetic brooms (magnetic sweepers) 'sweep up' iron particles from clean or rough floors or sandy surfaces. They work well in areas where it is very difficult to sweep up iron (or just the iron and nothing else) or it is not visible, such as in sand.
 
The strong magnet in the broom collects metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds.

Types

We have standard types and 'specials' available

In addition to the standard magnetic brooms on this page, we are happy to make a special broom for you on request. Other dimensions or attachments for forklift forks or trailers, etc.

Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Cleaning (iron disposal)

Cleaning & discharging of caught iron particles

Bar magnet type
The bar magnet has a scraper ring, with which you can slide the captured iron particles to the side. There the iron automatically falls from the bar housing.
 
Plate magnet type
This type of magnetic broom contains a strong plate magnet with a hinged separator plate (extractor plate) in front. After the floor has been swept the separation plate can be swung away, causing the iron particles to automatically fall off. It can then easily be swept up with a dustpan and broom.

Length : 900 mm
SVM-F-204x92-0900-B-F0E
SKU: SVMF040900
Stock *: 0
Advised max. installation height: 70-110 mm
Height: 92 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Length : 300 mm
SVM-N-204x55-0300-B-F1M
SKU: SVMN020300
Stock: 7
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Length : 600 mm
SVM-F-304x99-0600-B-F0E
SKU: SVMF050600
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Central greasing system For eddy current conveyor belt feeder
RECC-GS-15-B
SKU: E0090619
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Stainless steel hopper 53 liters | detachable
E0093963
SKU: E0093963
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Stainless steel hopper 41 liters | detachable
ASSY HOPPER RH1506
SKU: E0087935
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Size : 160 mm
HGR-SQ-160-FL-F-G-S
SKU: TPGC160078
Stock: 7
Max. tear off force: 3500 N
Advised working load: 1170 N
With magnetic grippers, you automatically pick up flat steel products or sheets up to 10 mm thick. They are quick and easy to switch, and specially designed for transferring, placing or positioning using a robotic arm.Magnetic grippers serve as end of arm tooling for sheets. They even hold perforated sheets effortlessly.

For sheets up to 10 mm thick
Switching: pneumatic
For robot End-of-arm tooling
Lifting power: up to 45 kg
Permanent magnet

Application

End of arm tooling

Magnetic grippers are ideal when you want to pick up, place or position flat, steel products with a robot. The applications are very diverse, such as:

pick-and-place of steel parts
handling perforated sheets with a robot arm
unstacking workpieces from crates (bin picking)
positioning sheets in presses
stacking or unstacking hot baking tins

The high temperature gripper is suitable for this last example. For example, you can also use it to load and unload high-grade steel in a press; it is formed at high temperatures.


Operation

Switching and control of the magnet gripper

The magnet gripper switches pneumatically. This moves the magnetic field and switches it on and off.
Control can be with a 5/3 or possibly a 5/2 valve.
An activated magnet gripper does not release its load, even if the air pressure or power supply is lost. This makes it a safe and reliable end-of-arm solution.

Practical tips

Things to look out for when using magnetic grippers:
When working with thin sheets (≤1 mm) you must consider the ‘peeling off effect’. This reduces the maximum breakaway force. In this situation, it is better to create a construction with multiple smaller grippers (e.g. 40 x 40 mm) than one or two large grippers.
A sheet can be damaged when the gripper contacts the sheet. If this is a problem, choose the version with a protective polyurethane cap (friction type).
When working with oiled sheets or with high acceleration of the robotic arm, a sheet can shift position. This, too, can be prevented through use of the type with a polyurethane friction pad.
Sometimes the surface of a sheet is not flat, so the vacuum does not work. In this case, magnetic grippers are an ideal solution. The more contact surface area the better, but a magnet gripper always works on ferromagnetic steel. Thus on round shapes too.
The vacuum does not work when there are holes in the sheet; the magnet gripper does. In this case, choose a gripper with larger dimensions than the hole, and test the chosen solution thoroughly.
For small workpieces, Goudsmit has very small grippers in the assortment. They have a low overall height and give extra strength to hold the workpiece in place. For example, choose type HGR-RO-020.
For thin sheets (≤4 mm) and oily sheets that stick together, the robot sometimes picks up several sheets together. Sheet separators prevent this. They are available both in permanent and pneumatically switchable versions.

Belt type : 1.3 mm Polyurethane antistatic, blue, with 1 cleat (A-shaped)
BELT 1.3MM PU RHFH800 2544x101
SKU: 45.1800087
Stock: 2
Suitable for belt width: 800 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

Diameter : 135 mm
SMR-N-D120x50-02E-S4-S
SKU: SEMR012078
Stock: 10
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 2
Weight: 1.2 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.