Pallet dimension : 1420 x 1120 mm
HPA-N-F-AL-1470-1170-B
SKU: TPFA141156
The lightweight magnetic palletizers have an aluminium housing. This makes them suitable for palletizing or depalletizing on a robot arm.For picking up large filled tins, aerosols, cans and glass jars with steel screw lids.

For robot End-of-arm tooling
Aluminium enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.


Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With Neoflux® (neodymium) medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
 
With Neodymium - Neoflux® - fine pole magnet system.
For palletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 1000 mm
HPA-N-F-AL-1250-1050-B
SKU: TPFA121056
The lightweight magnetic palletizers have an aluminium housing. This makes them suitable for palletizing or depalletizing on a robot arm.For picking up large filled tins, aerosols, cans and glass jars with steel screw lids.

For robot End-of-arm tooling
Aluminium enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.


Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With Neoflux® (neodymium) medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
 
With Neodymium - Neoflux® - fine pole magnet system.
For palletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 800 mm
HPA-N-F-AL-1250-0850-B
SKU: TPFA120856
The lightweight magnetic palletizers have an aluminium housing. This makes them suitable for palletizing or depalletizing on a robot arm.For picking up large filled tins, aerosols, cans and glass jars with steel screw lids.

For robot End-of-arm tooling
Aluminium enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.


Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With Neoflux® (neodymium) medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
 
With Neodymium - Neoflux® - fine pole magnet system.
For palletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1420 x 1120 mm
HPA-N-M-AL-1470-1170-B
SKU: TPMA141156
The lightweight magnetic palletizers have an aluminium housing. This makes them suitable for palletizing or depalletizing on a robot arm.For picking up large filled tins, aerosols, cans and glass jars with steel screw lids.

For robot End-of-arm tooling
Aluminium enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.


Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With Neoflux® (neodymium) medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
 
With Neodymium - Neoflux® - fine pole magnet system.
For palletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 1000 mm
HPA-N-M-AL-1250-1050-B
SKU: TPMA121056
The lightweight magnetic palletizers have an aluminium housing. This makes them suitable for palletizing or depalletizing on a robot arm.For picking up large filled tins, aerosols, cans and glass jars with steel screw lids.

For robot End-of-arm tooling
Aluminium enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.


Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With Neoflux® (neodymium) medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
 
With Neodymium - Neoflux® - fine pole magnet system.
For palletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 800 mm
HPA-N-M-AL-1250-0850-B
SKU: TPMA120856
The lightweight magnetic palletizers have an aluminium housing. This makes them suitable for palletizing or depalletizing on a robot arm.For picking up large filled tins, aerosols, cans and glass jars with steel screw lids.

For robot End-of-arm tooling
Aluminium enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.


Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With Neoflux® (neodymium) medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
 
With Neodymium - Neoflux® - fine pole magnet system.
For palletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1420 x 1120 mm
HPA-N-F-ST-1470-1170-B
SKU: TPFC141152
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 1000 mm
HPA-N-F-ST-1250-1050-B
SKU: TPFC121052
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 800 mm
HPA-N-F-ST-1250-0850-B
SKU: TPFC120852
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1420 x 1120 mm
HPA-N-M-ST-1470-1170-B
SKU: TPMC141152
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 1000 mm
HPA-N-M-ST-1250-1050-B
SKU: TPMC121052
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 800 mm
HPA-N-M-ST-1250-0850-B
SKU: TPMC120852
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1420 x 1120 mm
HPA-F-F-ST-1470-1170-B
SKU: TPBC141152
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 1000 mm
HPA-F-F-ST-1250-1050-B
SKU: TPBC121052
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Pallet dimension : 1200 x 800 mm
HPA-F-F-ST-1250-0850-B
SKU: TPBC120852
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Max. stack height : 100 mm
HSS-N-RD-D34-0160-B
SKU: TRSP341600
Stock *: 0
Max. sheet thickness: 3 mm
For specific applications, we have also developed a suitable sheet separator in the form of a rod.This type is very compact and easy to place into an opening in the sheet. Its round shape also makes it suitable for special contours.

Permanent magnetic
For sheets up to 3 mm thick
Max. stacking height 100 mm
Stainless steel enclosure

Operation

Sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.

Max. stack height : 560 mm
HSS-N-PF-140x175-0600-B
SKU: TPSP126001
Stock: 12
Max. sheet thickness: 4 mm
Connections: Pneumatic: G1/8" (2x)
Spread stacked steel sheets in automated processes one by one. These pneumatically switchable sheet separators have a neodymium magnet system.So you can easily add to or swap a stack of sheets.

Pneumatically switchable
Max. stacking height 560 mm
Stainless steel enclosure
With neodymium magnets

Operation

Operation of pneumatically switchable sheet separator

A powerful magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
 
The separator contains very powerful neodymium magnets that are moved forward by compressed air in the sheet separator. This switches the sheet separator on.
The new, patented fail-safe system ensures that the sheet separator always shuts itself off once the compressed air drops. This makes this sheet separator unique in terms of safety.
 
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.


Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Max. stack height : 490 mm
HSS-N-PF-140x175-0530-B
SKU: TPSP125301
Stock: 4
Max. sheet thickness: 4 mm
Connections: Pneumatic: G1/8" (2x)
Spread stacked steel sheets in automated processes one by one. These pneumatically switchable sheet separators have a neodymium magnet system.So you can easily add to or swap a stack of sheets.

Pneumatically switchable
Max. stacking height 560 mm
Stainless steel enclosure
With neodymium magnets

Operation

Operation of pneumatically switchable sheet separator

A powerful magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
 
The separator contains very powerful neodymium magnets that are moved forward by compressed air in the sheet separator. This switches the sheet separator on.
The new, patented fail-safe system ensures that the sheet separator always shuts itself off once the compressed air drops. This makes this sheet separator unique in terms of safety.
 
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.


Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Max. stack height : 410 mm
HSS-N-PF-140x176-0450-B
SKU: TPSP124501
Stock: 15
Max. sheet thickness: 4 mm
Connections: Pneumatic: G1/8" (2x)
Spread stacked steel sheets in automated processes one by one. These pneumatically switchable sheet separators have a neodymium magnet system.So you can easily add to or swap a stack of sheets.

Pneumatically switchable
Max. stacking height 560 mm
Stainless steel enclosure
With neodymium magnets

Operation

Operation of pneumatically switchable sheet separator

A powerful magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
 
The separator contains very powerful neodymium magnets that are moved forward by compressed air in the sheet separator. This switches the sheet separator on.
The new, patented fail-safe system ensures that the sheet separator always shuts itself off once the compressed air drops. This makes this sheet separator unique in terms of safety.
 
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.


Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Max. stack height : 300 mm
HSS-N-PF-140x176-0337-B
SKU: TPSP123301
Stock: 1
Max. sheet thickness: 4 mm
Connections: Pneumatic: G1/8" (2x)
Spread stacked steel sheets in automated processes one by one. These pneumatically switchable sheet separators have a neodymium magnet system.So you can easily add to or swap a stack of sheets.

Pneumatically switchable
Max. stacking height 560 mm
Stainless steel enclosure
With neodymium magnets

Operation

Operation of pneumatically switchable sheet separator

A powerful magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
 
The separator contains very powerful neodymium magnets that are moved forward by compressed air in the sheet separator. This switches the sheet separator on.
The new, patented fail-safe system ensures that the sheet separator always shuts itself off once the compressed air drops. This makes this sheet separator unique in terms of safety.
 
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.


Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Max. stack height : 110 mm
HSS-N-PA-150x158-0150-C
SKU: TPSP000017
Stock *: 0
Max. sheet thickness: 3 mm
Connections: Pneumatic: G¼" (2x)
Spread stacked steel sheets in automated processes one by one. These pneumatically switchable sheet separators have a neodymium magnet system.So you can easily add to or swap a stack of sheets.

Pneumatically switchable
Max. stacking height 560 mm
Stainless steel enclosure
With neodymium magnets

Operation

Operation of pneumatically switchable sheet separator

A powerful magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
 
The separator contains very powerful neodymium magnets that are moved forward by compressed air in the sheet separator. This switches the sheet separator on.
The new, patented fail-safe system ensures that the sheet separator always shuts itself off once the compressed air drops. This makes this sheet separator unique in terms of safety.
 
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.


Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Belt width : 1600 mm
ROEZ-09-C-160-W-G-L-B-B-B-B-NA
SKU: SZEB160004
Stock *: 0
Advised max. installation height: 600 mm
Magnet power cold/warm: 16 200 / 11 900 W
Heavy, robust and very powerful. Electromagnetic overband magnets have a deeply penetrating magnetic field and are therefore suitable for very thick layers. A control box is required. The magnet can be turned off for service or cleaning purposes.

Electrical power supply required
Max. installation height 600 mm
For belt width 800-1600 mm
Switchable (electromagnet)
Max. layer thickness 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates Ferrous parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overbelt magnetic separators are suitable for both the recovery of ferrous parts and the removal of iron impurities.
 
The electro overband magnet has the deepest holding field and is therefore the most suitable of all the overband magnets for the removal of steel particles from material streams with thick layers. Disadvantages are the higher power consumption and higher weight relative to the permanent overband magnets.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Overband placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Belt width : 1400 mm
ROE-08-C-140-W-G-R-B-R-B-B-NA
SKU: SEEB140023
Stock *: 0
Advised max. installation height: 520 mm
Magnet power cold/warm: 10 400 / 7600 W
Heavy, robust and very powerful. Electromagnetic overband magnets have a deeply penetrating magnetic field and are therefore suitable for very thick layers. A control box is required. The magnet can be turned off for service or cleaning purposes.

Electrical power supply required
Max. installation height 600 mm
For belt width 800-1600 mm
Switchable (electromagnet)
Max. layer thickness 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates Ferrous parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overbelt magnetic separators are suitable for both the recovery of ferrous parts and the removal of iron impurities.
 
The electro overband magnet has the deepest holding field and is therefore the most suitable of all the overband magnets for the removal of steel particles from material streams with thick layers. Disadvantages are the higher power consumption and higher weight relative to the permanent overband magnets.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Overband placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Belt width : 1200 mm
ROE-06-C-120-W-G-R-B-R-B-B-NA
SKU: SEEB120023
Stock *: 0
Advised max. installation height: 450 mm
Magnet power cold/warm: 7600 / 5600 W
Heavy, robust and very powerful. Electromagnetic overband magnets have a deeply penetrating magnetic field and are therefore suitable for very thick layers. A control box is required. The magnet can be turned off for service or cleaning purposes.

Electrical power supply required
Max. installation height 600 mm
For belt width 800-1600 mm
Switchable (electromagnet)
Max. layer thickness 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates Ferrous parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overbelt magnetic separators are suitable for both the recovery of ferrous parts and the removal of iron impurities.
 
The electro overband magnet has the deepest holding field and is therefore the most suitable of all the overband magnets for the removal of steel particles from material streams with thick layers. Disadvantages are the higher power consumption and higher weight relative to the permanent overband magnets.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Overband placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Belt width : 800 - 1000 mm
ROE-05-C-100-W-G-R-B-R-B-B-NA
SKU: SEEB100023
Stock *: 0
Advised max. installation height: 360 mm
Magnet power cold/warm: 5800 / 4300 W
Heavy, robust and very powerful. Electromagnetic overband magnets have a deeply penetrating magnetic field and are therefore suitable for very thick layers. A control box is required. The magnet can be turned off for service or cleaning purposes.

Electrical power supply required
Max. installation height 600 mm
For belt width 800-1600 mm
Switchable (electromagnet)
Max. layer thickness 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates Ferrous parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overbelt magnetic separators are suitable for both the recovery of ferrous parts and the removal of iron impurities.
 
The electro overband magnet has the deepest holding field and is therefore the most suitable of all the overband magnets for the removal of steel particles from material streams with thick layers. Disadvantages are the higher power consumption and higher weight relative to the permanent overband magnets.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Overband placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1000 mm
ROP-N3-C-100-W-G-L-B-B-B-NA
SKU: RONC100330
Stock *: 0
Weight: 605 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 800 mm
ROP-N3-C-080-W-G-L-B-B-B-NA
SKU: RONC080330
Stock *: 0
Weight: 520 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 650 mm
ROP-N3-C-065-W-G-L-B-B-B-NA
SKU: RONC065330
Stock *: 0
Weight: 465 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1200 mm
ROP-N3-C-120-W-H-L-B-B-B-NA
SKU: RONC120530
Stock *: 0
Weight: 680 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1000 mm
ROP-N3-C-100-W-H-L-B-B-B-NA
SKU: RONC100530
Stock *: 0
Weight: 595 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 650 mm
ROP-N3-C-065-W-H-L-B-B-B-NA
SKU: RONC065530
Stock *: 0
Weight: 455 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1200 mm
ROP-N3-C-120-W-G-L-B-B-B-NA
SKU: RONC120330
Stock: 1
Weight: 690 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 800 mm
ROP-N3-C-080-W-H-L-B-B-B-NA
SKU: RONC080530
Stock *: 0
Weight: 510 kg
Lightweight, compact and powerful. Suitable for fine fractions in small layer thickness, can also separate weakly magnetic parts. No control box required and available with hydro-motor. Often used in mobile installations.

Lightweight and compact
Stainless steel body
Electro or Hydro drive
Non-switchable (permanent magnet)
Capture Fe particles from 1 mm

Application

Application

These magnets are often used on mobile shredders or sieves because they are compact and lightweight. The magnetic separators are made of stainless steel so that they do not rust due to weather influences, such as rain. You can choose between electric or hydro motor for the drive roller. The magnet with hydro drive can be integrated to the existing hydraulic system of the mobile installation. So that no additional power supply is required.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1400 mm
ROP-F6-I-140-W-G-L-B-B-B-NA
SKU: ROFI140360
Stock *: 0
Advised max. installation height: 450 mm
Suitable for: Inline mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1400 mm
ROP-F5-I-140-W-G-L-B-B-B-NA
SKU: ROFI140350
Stock *: 0
Advised max. installation height: 400 mm
Suitable for: Inline mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1200 mm
ROP-F5-I-120-W-G-L-B-B-B-NA
SKU: ROFI120350
Stock *: 0
Advised max. installation height: 400 mm
Suitable for: Inline mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Ferrite - reinforced Tapered-after roller
HRA-F-102x44-BB-0335-R-W
SKU: TBBB033554
Stock *: 0
Width: 102 mm
Height: 44 mm
Length: 335 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Suitable for belt width : 1200 mm
ROP-F4-I-120-W-G-L-B-B-B-NA
SKU: ROFI120340
Stock *: 0
Advised max. installation height: 320 mm
Suitable for: Inline mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Ferrite - reinforced Tapered-before roller
HRA-F-102x44-BA-0335-R-W
SKU: TBBA033554
Stock *: 0
Width: 102 mm
Height: 44 mm
Length: 335 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Ferrite - reinforced 750 mm
HRA-F-102x44-AA-0750-R-W
SKU: TBAA075054
Stock *: 0
Width: 102 mm
Height: 44 mm
Water-resistant: yes
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Ferrite - reinforced Weakening infeed
HRA-F-102x44-AC-0500-R-W
SKU: TBAC050054
Stock *: 0
Width: 102 mm
Height: 44 mm
Length: 500 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Ferrite - reinforced Weakening outfeed
HRA-F-102x44-AB-0500-R-W
SKU: TBAB050054
Stock *: 0
Width: 102 mm
Height: 44 mm
Length: 500 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Adapter set from square to round AISI304 | #350-Ø350
REDUCER DN350 EN1092-1
SKU: A513_030000
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Length : 300 mm
SVM-F-304x99-0300-B-F0E
SKU: SVMF050300
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Length : 350 mm
SVM-F-204x92-0350-B-F0E
SKU: SVMF040350
Stock: 4
Type: VMF4
Advised max. installation height: 70-110 mm
Interface/connection dim's: Threaded hole M8 (4x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Length : 400 mm
BAR-ES-23-400-25-2M8-NW-B
SKU: SBAQA100040-400
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M8 (2x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Suitable for belt width : 1000 mm
ROP-F4-I-100-W-G-L-B-B-B-NA
SKU: ROFI100340
Stock *: 0
Advised max. installation height: 320 mm
Suitable for: Inline mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Length : 400 mm
BAR-ES-23-400-25-2M6-NW-B
SKU: SBAQA100020-400
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M6 (2x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Length : 400 mm
BAR-ES-23-400-25-1M8-NW-B
SKU: SBAQA100030-400
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M8 (1x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Length : 400 mm
BAR-ES-23-400-25-1M6-NW-B
SKU: SBAQA100010-400
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M6 (1x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Length : 500 mm
BAR-N-23-500-25-2M8-NW-B
SKU: SBAMA100040-500
Interface/connection dim's: Threaded hole M8 (2x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Length : 500 mm
BAR-N-23-500-25-2M6-NW-B
SKU: SBAMA100020-500
Interface/connection dim's: Threaded hole M6 (2x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Length : 500 mm
BAR-N-23-500-25-1M8-NW-B
SKU: SBAMA100030-500
Interface/connection dim's: Threaded hole M8 (1x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Length : 500 mm
BAR-N-23-500-25-1M6-NW-B
SKU: SBAMA100010-500
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Length : 250 mm
SVM-N-114x34-0250-B-F1M
SKU: SVMN060250
Stock *: 0
Advised max. installation height: 65-80 mm
Height: 34 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

Suitable for belt width : 1000 mm
ROP-F3-I-100-W-G-L-B-B-B-NA
SKU: ROFI100330
Stock *: 0
Advised max. installation height: 280 mm
Suitable for: Inline mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Length : 450 mm
BAR-HT-23-450-25-2M8-NW-B
SKU: SBANA100040-450
Interface/connection dim's: Threaded hole M8 (2x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Suitable for belt width : 800 mm
ROP-F3-I-080-W-G-L-B-B-B-NA
SKU: ROFI080330
Stock *: 0
Advised max. installation height: 280 mm
Suitable for: Inline mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Suitable for belt width : 1600 mm
ROP-F6-C-160-W-G-L-B-B-B-NA
SKU: ROFC160360
Stock *: 0
Advised max. installation height: 450 mm
Suitable for: Cross mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

Length : 450 mm
BAR-HT-23-450-25-2M6-NW-B
SKU: SBANA100020-450
Interface/connection dim's: Threaded hole M6 (2x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.