Precision single universal joint WEN with needle bearing DIN808 bore 18H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel 35SMnPb10, Bearing Parts 18NiCrMo5Pb. Max. Operating Angle 45°. The needle-bearing universal joints have almost zero backlash, high accuracy and good turning properties. These special needle-rollers without cage can take high loads even at large operating angles. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - which guarantees an extremely long service life. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63113700N

Cardan joint KE outer diameter 32mm both sides bore 20H7 material steel total length 86mm
Material: Steel C 45. Max. Operating Angle 45°. The cardan joints KE are, other than the cardan joints with needle-roller bearing, only sliding-contact bearings. Their scope of application is therefore limited to slow running drives. The respective maximum speeds depend on operating angle and load, but must never exceed 1000 rpm. The maximum torque values listed in the table are limits, which must neither be exceeded. They may only be used to their full extend with intermittent operation or at low speed. The following limit applies: The product of speed (rpm) x working angle (degrees) may not exceed the reference number 500. This means, e.g., for a working angle of 10 degrees a max. speed of 50 rpm. If, however, the maximum torque is not taken to the limit, speed and working angle can be larger. At 0.5 x max. torque applies: speed x working angle, smaller or equal 4.000. In case of doubt choose larger joint. At continuous operation the cardan joints need to be sufficiently lubricated. If no drip-feed lubrication is possible, lubricate the joints at least once a day. Another possibility is to cover the joints with a bellow, filled with a suitable lubricant. Typ A: without bores. Type B: with bores. Type N: with bores and keyways DIN 6885-1 on both sides.
Article ID: 63013200

Precision single universal joint WER DIN 808 simple, bore 16H7
stainless steel 1.4301 total length 95mm outer diameter 32mm
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199232

Precision single universal joint WE DIN808 simple bore 22H7 material steel total length 95mm outer diameter 47mm
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63124700

Precision single universal joint WEN with needle bearing DIN808 simple bore 20H7 material steel total length 108mm outer diameter 40mm
Material: Steel 35SMnPb10, Bearing Parts 18NiCrMo5Pb. Max. Operating Angle 45°. The needle-bearing universal joints have almost zero backlash, high accuracy and good turning properties. These special needle-rollers without cage can take high loads even at large operating angles. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - which guarantees an extremely long service life. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63114000

Double universal joint WDL similar to DIN808 bore 16H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel. Max. Operating Angle 90. These low-price, single universal joints are especially suited for manual operation at low torques. As the contact surfaces are not hardened/ground, they can be only used at high speeds for short intervals. *only for short intervals Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63072900N

Ball joint RW bore 16H7 material steel
outer diameter 32mm total length 80mm
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63133200

Precision single universal joint WER DIN808 bore 12H7 with keyway DIN 6885-1 tolerance JS9 on both sides stainless steel 1.4301
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199226N

Precision double universal joint WD DIN808 bore 8H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63171600N

Ball joint RW bore 8H7 with keyway DIN 6885-1 on both sides outer diameter 16mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63131600N

Precision single universal joint WER DIN808 bore 14H7 with keyway DIN 6885-1 tolerance JS9 on both sides stainless steel 1.4301
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199229N

Cardan joint KE outer diameter 40mm no bore material steel total length 108mm
Material: Steel C 45. Max. Operating Angle 45°. The cardan joints KE are, other than the cardan joints with needle-roller bearing, only sliding-contact bearings. Their scope of application is therefore limited to slow running drives. The respective maximum speeds depend on operating angle and load, but must never exceed 1000 rpm. The maximum torque values listed in the table are limits, which must neither be exceeded. They may only be used to their full extend with intermittent operation or at low speed. The following limit applies: The product of speed (rpm) x working angle (degrees) may not exceed the reference number 500. This means, e.g., for a working angle of 10 degrees a max. speed of 50 rpm. If, however, the maximum torque is not taken to the limit, speed and working angle can be larger. At 0.5 x max. torque applies: speed x working angle, smaller or equal 4.000. In case of doubt choose larger joint. At continuous operation the cardan joints need to be sufficiently lubricated. If no drip-feed lubrication is possible, lubricate the joints at least once a day. Another possibility is to cover the joints with a bellow, filled with a suitable lubricant. Typ A: without bores. Type B: with bores. Type N: with bores and keyways DIN 6885-1 on both sides.
Article ID: 63004000

Precision double universal joint WD DIN808 bore 10H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63172000N

Precision double universal joint WD DIN808 bore 12H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63172600N

Ball joint RW bore 10H7 with keyway DIN 6885-1 on both sides outer diameter 20mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63132000N

Ball joint RW bore 12H7 with keyway DIN 6885-1 on both sides outer diameter 24mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63132400N

Cardan joint KE outer diameter 32mm bore 20H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel C 45. Max. Operating Angle 45°. The cardan joints KE are, other than the cardan joints with needle-roller bearing, only sliding-contact bearings. Their scope of application is therefore limited to slow running drives. The respective maximum speeds depend on operating angle and load, but must never exceed 1000 rpm. The maximum torque values listed in the table are limits, which must neither be exceeded. They may only be used to their full extend with intermittent operation or at low speed. The following limit applies: The product of speed (rpm) x working angle (degrees) may not exceed the reference number 500. This means, e.g., for a working angle of 10 degrees a max. speed of 50 rpm. If, however, the maximum torque is not taken to the limit, speed and working angle can be larger. At 0.5 x max. torque applies: speed x working angle, smaller or equal 4.000. In case of doubt choose larger joint. At continuous operation the cardan joints need to be sufficiently lubricated. If no drip-feed lubrication is possible, lubricate the joints at least once a day. Another possibility is to cover the joints with a bellow, filled with a suitable lubricant. Typ A: without bores. Type B: with bores. Type N: with bores and keyways DIN 6885-1 on both sides.
Article ID: 63013200N

Precision double universal joint WD DIN808 double bore 14H7 material steel
total length 85mm outer diameter 25mm
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63172900

Precision single universal joint WER DIN808 bore 16H7 with keyway DIN 6885-1 tolerance JS9 on both sides stainless steel 1.4301
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199232N

Precision single universal joint WE DIN808 bore 22H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63124700N

Precision single universal joint WEN with needle bearing DIN808 bore 20H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel 35SMnPb10, Bearing Parts 18NiCrMo5Pb. Max. Operating Angle 45°. The needle-bearing universal joints have almost zero backlash, high accuracy and good turning properties. These special needle-rollers without cage can take high loads even at large operating angles. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - which guarantees an extremely long service life. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63114000N

Double universal joint WDL similar to DIN808 bore 18H7 material steel
total length 112mm outer diameter 32mm
Material: Steel. Max. Operating Angle 90. These low-price, single universal joints are especially suited for manual operation at low torques. As the contact surfaces are not hardened/ground, they can be only used at high speeds for short intervals. *only for short intervals Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63073200

Single universal joint WEL similar to DIN808 bore 30H7 material: steel
total length 122mm outer diameter 58mm
Material: Steel. Max. Operating Angle 45°. These low-price, single universal joints are especially suited for manual operation at low torques. As the contact surfaces are not hardened/ground, they can only be used at high speeds for short intervals. *only for short intervals Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63065800

Ball joint RW bore 18H7 material steel
outer diameter 36mm total length 90mm
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63133600

Precision double universal joint WD DIN808 double bore 16H7 material steel
total length 100mm outer diameter 29mm
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63173200

Ball joint RW bore 14H7 with keyway DIN 6885-1 on both sides outer diameter 28mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63132800N

Precision single universal joint WE DIN808 simple bore 25H7 material steel total length 108mm outer diameter 50mm
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63125000

Precision cardan joint WE DIN808 single, bore 25H7 material steel total length 105mm outer diameter 52mm
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63125200

Precision double universal joint WD DIN808 bore 14H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63172900N

Precision single universal joint WER DIN 808 simple, bore 18H7
stainless steel 1.4301 total length 108mm outer diameter 37mm
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199237

Double universal joint WDL similar to DIN808 bore 18H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel. Max. Operating Angle 90. These low-price, single universal joints are especially suited for manual operation at low torques. As the contact surfaces are not hardened/ground, they can be only used at high speeds for short intervals. *only for short intervals Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63073200N

Telescopic universal-joint shaft UW made from plastic/brass bore 12.70mm telescoped length 500mm max. travel 284mm
Material: acetal (black). Cross-pieces: brass. Joint faces are fitted with brass inserts, with 2 set screws per hub. Temperature range: -20°C to + 60°C. To shorten the teleshafts, please always cut off the same length on either side. * The stated peak torque refers to Lmin. (telescope retracted). The max. torque for extended telescope has to be determined empirically and subject to the respective application. ** Bore-reducing bushes see below. 1) Joint faces fitted with brass inserts with 2 set screws per hub. 2) Joints only fitted with metal inserts, without set screws.

Article ID: 63082800

Single universal joint WEL similar to DIN808 bore 30H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel. Max. Operating Angle 45°. These low-price, single universal joints are especially suited for manual operation at low torques. As the contact surfaces are not hardened/ground, they can only be used at high speeds for short intervals. *only for short intervals Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63065800N

Double universal joint WDL similar to DIN808 bore 20H7 material steel
total length 128mm outer diameter 40mm
Material: Steel. Max. Operating Angle 90. These low-price, single universal joints are especially suited for manual operation at low torques. As the contact surfaces are not hardened/ground, they can be only used at high speeds for short intervals. *only for short intervals Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63074000

Precision double universal joint WD DIN808 bore 16H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63173200N

Precision single universal joint WE DIN808 bore 25H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63125000N

Precision single universal joint WE DIN808 bore 25H7 with keyway DIN 6885-1 tolerance JS9 on both sides total length 105mm steel
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63125200N

Precision single universal joint WER DIN808 bore 18H7 with keyway DIN 6885-1 tolerance JS9 on both sides stainless steel 1.4301
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199237N

Precision single universal joint WEN with needle bearing DIN808 simple bore 25H7 material steel total length 132mm outer diameter 50mm
Material: Steel 35SMnPb10, Bearing Parts 18NiCrMo5Pb. Max. Operating Angle 45°. The needle-bearing universal joints have almost zero backlash, high accuracy and good turning properties. These special needle-rollers without cage can take high loads even at large operating angles. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - which guarantees an extremely long service life. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63115000

Precision single universal joint WER DIN 808 simple, bore 20H7
stainless steel 1.4301 total length 108mm outer diameter 40mm
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199240

Ball joint RW bore 16H7 with keyway DIN 6885-1 on both sides outer diameter 32 mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63133200N

Double universal joint WDL similar to DIN808 bore 20H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel. Max. Operating Angle 90. These low-price, single universal joints are especially suited for manual operation at low torques. As the contact surfaces are not hardened/ground, they can be only used at high speeds for short intervals. *only for short intervals Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63074000N

Ball joint RW bore 20H7 material steel
outer diameter 40mm total length 100mm
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63134000

Telescopic universal-joint shaft UW made from plastic/brass bore 20mm telescoped length 564mm max. travel 304mm
Material: acetal (black). Cross-pieces: brass. Joint faces are fitted with brass inserts, with 2 set screws per hub. Temperature range: -20°C to + 60°C. To shorten the teleshafts, please always cut off the same length on either side. * The stated peak torque refers to Lmin. (telescope retracted). The max. torque for extended telescope has to be determined empirically and subject to the respective application. ** Bore-reducing bushes see below. 1) Joint faces fitted with brass inserts with 2 set screws per hub. 2) Joints only fitted with metal inserts, without set screws.

Article ID: 63083600