Manual sliding valve, Operating temperature 0 °C to 70 °C, G 1/8 IT, AF 14, PN max. 10 bar
For use on devices that have to be vented whenever they are turned off, either because of safety regulations or for technical reasons. The pneumatic devices are disconnected from the system and simultaneously vented each time they are shut off.
Quick relief valve »lineonline«, with silencer, Hose - hose, for hose Ø 4 mm, Operating pressure 1 - 10 bar
Exhaust can be silenced by a stainless steel silencer or conveyed using a push-in fitting with an air exhaust device.
Hose security cable, For tube O.D. 13 - 35 mm, Galvanised steel, Length ca. 516 mm
For the security of two hoses connected, protecting against the "whip" when to hoses unintentional disconnect.
Ball valve, Manual lever, Basic design, IT/IT, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 3/8, DN 10, PN max. 50 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.
Ball valve, Butterfly handle, Basic design, IT/ET, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 3/8, PN max. 50 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.
Ball valve, Butterfly handle, Basic design, IT/IT, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 3/8, PN max. 50 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.
Check valve, DN 20, Brass, Metallic sealing, Operating temperature 0 °C to 90 °C, G 3/4, PN max. 16 bar
Applications: Water (no steam), neutral and non-corrosive liquid media, mineral oils.
Only suitable for liquid media. Flap valve closes by gravity, therefore only possible to be installed horizontally!
Dirt strainer, bright brass, Sieve insert mesh width 0.5 mm, Operating temp. -20 °C to 110 °C, G 3/4, DN 20, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.
Throttle check valve »ASC«, in block shape, Aluminium, Operating temperature max. 70 °C, G 1/8, PN max. 10 bar
These valves are restricted in the flow direction and have free passage in the opposite direction.
Pressure reducing valve, G 1/4 interior / exterior, AF 17, Set pressure 6 bar, Input pressure max. 15 bar, Material: Brass
Industry, trade and repair shops often require working pressures of 15 bar or less.
These pressure reducing valves, which are screwed directly onto the tool, enable that the pressure can be reduced to the selected working pressure.
Benefits:
- Significantly reduced risk of accidents
- Longer tool life with fewer malfunctions
- Lower noise levels at the workplace
Pressure reducing valve, G 1/4 interior / exterior, AF 17, Set pressure 5 bar, Input pressure max. 15 bar, Material: Brass
Industry, trade and repair shops often require working pressures of 15 bar or less.
These pressure reducing valves, which are screwed directly onto the tool, enable that the pressure can be reduced to the selected working pressure.
Benefits:
- Significantly reduced risk of accidents
- Longer tool life with fewer malfunctions
- Lower noise levels at the workplace
Pressure reducing valve, G 1/4 interior / exterior, AF 17, Set pressure 4 bar, Input pressure max. 15 bar, Material: Brass
Industry, trade and repair shops often require working pressures of 15 bar or less.
These pressure reducing valves, which are screwed directly onto the tool, enable that the pressure can be reduced to the selected working pressure.
Benefits:
- Significantly reduced risk of accidents
- Longer tool life with fewer malfunctions
- Lower noise levels at the workplace
Pressure reducing valve, G 1/4 interior / exterior, AF 17, Set pressure 3 bar, Input pressure max. 15 bar, Material: Brass
Industry, trade and repair shops often require working pressures of 15 bar or less.
These pressure reducing valves, which are screwed directly onto the tool, enable that the pressure can be reduced to the selected working pressure.
Benefits:
- Significantly reduced risk of accidents
- Longer tool life with fewer malfunctions
- Lower noise levels at the workplace
Check valve, DN 10, Brass, Soft sealed, Operating temperature 0 °C to 90 °C, G 3/8, PN max. 16 bar
Applications: Water (no steam), neutral and non-corrosive liquid media, mineral oils.
Only suitable for liquid media. Flap valve closes by gravity, therefore only possible to be installed horizontally!
Throttle check valve, Discharge throttle (»C«) quick connector Hose 5/3, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) quick connector Hose 6/4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) quick connector Hose 8/6, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) threaded connection G 1/8 i., G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) quick connector Hose 6/4, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) quick connector Hose 5/3, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) quick connector Hose 4/2.5, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) threaded connection M5 i., M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Pressure reducing valve, G 1/4 interior / exterior, AF 17, Set pressure 2 bar, Input pressure max. 15 bar, Material: Brass
Industry, trade and repair shops often require working pressures of 15 bar or less.
These pressure reducing valves, which are screwed directly onto the tool, enable that the pressure can be reduced to the selected working pressure.
Benefits:
- Significantly reduced risk of accidents
- Longer tool life with fewer malfunctions
- Lower noise levels at the workplace
Throttle valve, Both sides throttling (»B«) quick connector Hose 6/4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) quick connector Hose 5/3, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) quick connector Hose 8/6, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) quick connector Hose 8/6, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) quick connector Hose 5/3, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) Threaded connection G 1/8 IT, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) push-in connector hose 8, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) push-in connector hose 6, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) push-in connector hose 8, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) quick connector Hose 6/4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) push-in connector hose 8, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) push-in connector hose 6, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) push-in connector hose 6, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) push-in connector hose 4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) push-in connector hose 4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) Threaded connection G 1/8 i., G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) push-in connector hose 4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) push-in connector hose 6, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) push-in connector hose 6, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) push-in connector hose 6, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) quick connector Hose 6/4, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Discharge throttle (»C«) push-in connector hose 4, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
Throttle check valve, Supply air throttle (»V«) quick connector Hose 6/4, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) push-in connector hose 4, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) quick connector Hose 5/3, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) quick connector Hose 4/2.5, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.
Throttle valve, Both sides throttling (»B«) Threaded connection M5 IT, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.