Pressure regulator for potable water, DVGW not necessary, incl. pressure gauge, Brass sieve cup, R 1 1/2, Control range 1.5-12 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

Compact cylinder »ACP«, double-acting, Piston Ø 100, Stroke 50, Connection G 1/4, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Throttle valve, Both sides throttling (»B«) quick connector Hose 10/8, G 3/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.

Distributor »multifix«, Wide design, Size 3, G 1/2, with 4 outlets: 2 x G 1/4 and 2 x G 1/2, Input pressure max. 16 bar
Wide or narrow, four-way manifolds.

Push-in T-fitting »Blue Series«, rotating, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Bushing 270, IT/IT, Rp 1 1/2, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

T-piece 130, IT/IT/IT, Rp 2, T-branch reducing Rp 1, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Locking plug »click-clock«, Plug nipple 3 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 80 °C, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Feather key DIN 6885 version A 5 x 5 x 28 mm material stainless steel 1.4571
Material: Stainless steel 1.4571.

Version A.

Article ID: 61899102

Clamp collar single-split steel C45 black oxide finished bore 90mm with bolt DIN 912 12.9
Material: Steel C45, black oxide finish. Screw steel 12.9.Features:
does not damage the shaft, stronger clamping force than with set
collars, even distribution of clamping forces, easy readjustment,
precision honed bores. The threads of the screws DIN 912 are covered
with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range:
-40°C to +175°C.Remarks to collars from steel:The
black oxide on the clamping collars is formulated as part of the total
performance of the product. It enhances the holding ability of the
collar, it efficiently reduces slipping on the shaft, has
anti-stick-slip characteristics and helps to keep the torque rating of
the screw within its designed parameters. The oxide layer also provides
corrosion protection.

Article ID: 62319000

Hexagonal trapezoidal nut steel C35Pb Tr.70 x 10 single-start right length 105mm wrench size 90mm
Material: Steel C35Pb.

Tolerance zone 7H.

Height = 1,5 x diameter.

Attention:
Steel nuts get very easily thightened on a spindle
made from Steel or stainless steel.
This nuts are only for clamping, manual adjustments or as fastening nut.
Not suitable for drive systems.

Article ID: 64317000

Neodymium (NdFeB) 500 N
PM-HS-N-SG-D40x8xd5,5/10.3
SKU: GM17429
Stock: 0
Holding force: 500 N
Height: 8 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Chain connecting link type 11 / E with bent attachments 06 B-1-K1 attachments slim version on one side
Material: Special chain steel. According to DIN ISO 606 (ex DIN 8187).
Article ID: 10100301

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 12x9 mm, PN at 23 °C max. 8 bar, red, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Pressure regulator for potable water, DVGW not necessary, incl. pressure gauge, Brass sieve cup, R 2, Control range 1.5 - 12 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ125,Stroke110,G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Tempered coupling DN 9, Exterior thread, Brass 2.0401, G 1/2 straight, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Distributor »multifix«, Wide design, Size 3, G 3/4, with 4 outlets: 2 x G 1/4 and 2 x G 1/2, Input pressure max. 16 bar
Wide or narrow, four-way manifolds.

Bushing with exterior hexagonal, G 1, AF 41, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 2, Length 120 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Reducing piece 241, ET/IT, R 3 o., Rp 1 2/2 i., Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight screw-on fitting G 1/8 i., for hose 4/6 mm, AF 14, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Round trapezoidal nut red brass Rg7 Tr.44 x 7 single-start left length 88mm outer diameter 80mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64384400

Clamp collar double-split steel C45 black oxide finished bore 90mm with bolts DIN 912 12.9
Material: Steel C45, black oxide finish. Screws steel 12.9.Features:
does not damage the shaft, stronger clamping force than with set
collars, even distribution of clamping forces, easy readjustment,
precision honed bores. The threads of the screws DIN 912 are covered
with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range:
-40°C to +175°C.Remarks to collars from steel:The
black oxide on the clamping collars is formulated as part of the total
performance of the product. It enhances the holding ability of the
collar, it efficiently reduces slipping on the shaft, has
anti-stick-slip characteristics and helps to keep the torque rating of
the screw within its designed parameters. The oxide layer also provides
corrosion protection.
Article ID: 62349000

Ferrite 14 N
PM-HS-F-SG-D16x4.5xd3.5/6.5
SKU: GM16600
Stock: 28
Diameter (D): 16 mm
Height: 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Chain connecting link type 11 / E with straight attachments 06 B-1-M1 attachments slim version on one side
Material: Special chain steel.According to DIN ISO 606 (ex DIN 8187)
Article ID: 10100331

Slide set DZ 5321 SC slide length 500mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Self-close. Hold-in in closed position. Bracket Mount for electrical cabinets on request. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk / 6mm countersunk Euro screw. Use all mounting positions to achieve the max. load rating. Ordering details: e.g.: Product no. 649 042 30, Slides 5321 SC
Article ID: 64904250

timing bar T10 24 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16492400

Glycerine pressure gauge, bracket fastening, triangle front ring, Connection, rear, centric, G 1/4, Meas. range 0 - 1.6 bar, Ø 63
Bourdon-tube pressure gauge in standard design, with clamp fixing.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 12x9 mm, PN at 23 °C max. 8 bar, silver, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ125,Stroke110, G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight push-in fitting, Exterior hexagonal,G 1/8 o. for hose exterior Ø 6 mm,Working pressure max. 20 bar,Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Screw-in hose connector R 1 1/2 o., for hose I.D. 32 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Pressure gauge connection nipple made of brass, G 1/2 bushing, G 3/8 taps, PN 600 bar

Push-in T-fitting »Blue Series« mini, L-shape, rotating, M5, for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

T-piece 130, IT/IT/IT, Rp 2, T-branch reducing Rp 3/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galva.
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Nipple for couplings I.D. 2.7, bright brass, for hose 5x3, AF 7, Operating pressure 0 - 35 bar, Med./ambient temp. -20°C to 100°C

Ferrite 27 N
PM-HS-F-SG-D20x6xd4.1/9.4
SKU: GM16601
Stock: 45
Diameter (D): 20 mm
Height: 6 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Replacement chain for chain coupling type 3012 06 B-2 length 12 links including spring clip link
Material: Steel. With connection link with clip. These chains fit only for chain couplings with casing, types 3012 to 6020.

Article ID: 14033112

Slide rail DZ 9301 slide length 610mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold by piece (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Lengths to 1.5 meters. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles ( to 217 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905124

Clamp collar single-split steel C45 zinc plated bore 90mm with screw DIN 912 12.9
Material: Steel C45 zinc-plated. Screw steel 12.9.Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores. The threads of the screws DIN 912 are covered with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range: -40°C to +175°C.
Article ID: 62388190

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 12x9 mm, PN at 23 °C max. 8 bar, yellow, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Storz coupling, Hose supports, for shell binding, rotating, V4A, Storz size 52-C, I.D. 38, Operating pressure max. 16 bar
High-quality series in V4A stainless steel. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Industrial plant engineering, shipbuilding, chemical industry.

Fitting 331, flat sealing, IT/ET, Rp/R 1/4, NBR seal, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galva.
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Intermediate piece for measurement device holder for mounting pressure gauges, according to DIN 16281, G 1/2, CrNi steel 1.4571
For mounting shut-off valves with a pressure gauge directly on the wall.

Fitting elbow 98, conical sealing, IT/ET, Rp 1/2, R 1/2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galva.
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Flat suction cup, round, Silicone material, »PFG«, ø:40 suitable connection nipple IT G 1/8, suitable connection nipple ET G 1/8
Robust and hard-wearing suction pad with a single sealing lip.
Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to handle smooth or slightly rough surfaces. Due to its flat shape, it can grip the workpiece in a very short time and withstand the forces that result from fast movement of the object during handling. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Very short evacuation timesSuitable for high lateral forcesGood intrinsic stability when attached to the loadSupports on the bottomVery short cycle timesHigh suction forces with small dimensions

Applications:
Handling workpieces with smooth or slightly rough surfaces, e.g. metal sheets,
cardboard boxes, sheets of glass, plastic parts and sheets of wood.

T-piece 130, IT/IT/IT, Rp 2, T-branch reducing Rp 1 1/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galva.
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Angled screw-in fitting G 1/8 o., for hose 4/6 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Ferrite 72 N
PM-HS-F-SG-D32x7xd5.5/11.5
SKU: GM16602
Stock: 282
Diameter (D): 32 mm
Height: 7 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Bolt 1/2" x 1" for Taper bush 2517 and 2525
Material:Steel. Supply: One screw. Attention: Order quantity as needed. Up to size 3030, taper bushes have two screws, from 3525 three screws. Assembly instructions In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 62250699

V-belt pulley material aluminium profile XPB, SPB and B (17) 2 grooves nominal diameter 250mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. * without cast-iron hub reinforcement.

Article ID: 15422500

Clamp collar double-split steel C45 zinc-plated bore 90mm with screws DIN 912 12.9
Material: Steel C45, zinc-plated . Screws steel 12.9.Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores. The threads of the screws DIN 912 are covered with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range: -40°C to +175°C.
Article ID: 62388490

Filter regulator »variobloc«, PC container, Protective cage and pressure gauge, Size 1, G 1/4, Input pressure max. 16 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design, combined
with a centrifugal separator.
The pressure setting can be locked by pushing the knob down.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Mist oiler »multifix«, Metal container, Viewing tube, Size 5, G 1, Input pressure max. 20 bar, Medium / ambient temp. max. 60 °C
Proportional lubricators, oil can be filled under pressure.

Distributor strip, Outlets both sides, front and back, Input 2 x 3/8, Output 4 + 4 x 1/4, Aluminium
For easy assembly of compressed air taps (screw fittings, unions, couplings, etc.).
Optionally with 2, 3, 4, or 6 outlets on one side or both sides.

Needle valve, Brass, with fine control, Operating temperature -30 °C to 110 °C, G 1/2 IT, DN 4, AF 27, PN max. 16 bar

Valve replacement set, for pressure regulator for potable water, R 1/2 and R 3/4

Adapter for needle valve nozzles and rubber nozzles

Chain for GEKA blind coupling