Throttle check valve, Discharge throttle (»C«) push-in connector hose 10, G 3/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Compact cyl.ISO 21287, double-acting, female piston rod, magnet, PistonØ25, Stroke70, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Hinge pin clamp, Stainless steel 1.4301 (W4), Clamping range 51.0 - 55.0 mm, Belt width 20.0 mm, rec. tightening torque 10.0 Nm

Reducing nipple, R 3/4 o., G 1/2 i., AF 27, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

Male branch tee »universal short«, rotating, 1/2, hose-Ø10, taper seat, Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Reducing nipple, long type, M5 o., M3 i., AF 7, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

25 mm Samarium-Cobalt (SmCo)
SMCO POT VLAK 25X7
SKU: GM17107
Stock: 0
Holding force: 150 N
Height: 7 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Knurled thumb screw 421 M5 x 25mm long set screw steel zinc plated
Material: Head: Plastic thermoplast (polyamide) black, glossy finish Threaded bolt: Steel, zinc plated, chromatised blue

Article ID: 65378100

Trapeziodal-threaded spindle DIN 103 Tr.16 x 4 x 2000mm long single-start left material 1.4305 rolled
Material: 1.4305. Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length sawed (length may be longer than nominal length), edges not broken.
Article ID: 64099616

Cardan joint KE outer diameter 50mm no bore material steel total length 132mm
Material: Steel C 45. Max. Operating Angle 45°. The cardan joints KE are, other than the cardan joints with needle-roller bearing, only sliding-contact bearings. Their scope of application is therefore limited to slow running drives. The respective maximum speeds depend on operating angle and load, but must never exceed 1000 rpm. The maximum torque values listed in the table are limits, which must neither be exceeded. They may only be used to their full extend with intermittent operation or at low speed. The following limit applies: The product of speed (rpm) x working angle (degrees) may not exceed the reference number 500. This means, e.g., for a working angle of 10 degrees a max. speed of 50 rpm. If, however, the maximum torque is not taken to the limit, speed and working angle can be larger. At 0.5 x max. torque applies: speed x working angle, smaller or equal 4.000. In case of doubt choose larger joint. At continuous operation the cardan joints need to be sufficiently lubricated. If no drip-feed lubrication is possible, lubricate the joints at least once a day. Another possibility is to cover the joints with a bellow, filled with a suitable lubricant. Typ A: without bores. Type B: with bores. Type N: with bores and keyways DIN 6885-1 on both sides.
Article ID: 63005000

3/2-way valve, electropneum., monostable, G 1/4, NC, 24 V DC, Operating pre. 2.5 - 10 bar, Operating temp. -10 °C to 60 °C

Pressure regulator for water, incl. pressure gauge, R 1 1/2, Control range 0.2 - 2 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated piston valve or single-seated diaphragm valve and built-in strainer. Specially designed for use with water.
The device is also suitable for all other applications involving neutral non-sticky liquids, air and neutral non-flammable gases.

Check valve, DN 40, Red brass, Metallic sealing, Operating temperature -10 °C to 80 °C, G 1 1/2, PN max. 16 bar
Applications: Water (no steam), neutral and non-corrosive liquid media, mineral oils.

Only suitable for liquid media. Flap valve closes by gravity, therefore only possible to be installed horizontally!

Throttle valve, Both sides throttling (»B«) push-in connector hose 10, G 3/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ32, Stroke45,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

GEKA threaded piece, rigid, bright brass, G 1/4 exterior, Operating pressure max. 40 bar, Medium / ambient temp. -10 °C to 90 °C
Claw couplings (claw distance: 40 mm) made of brass for water, industrial, mortar, suction and discharge hoses. Suitable for a wide range of applications, e.g. industrial plant engineering, civil and structural engineering, environmental engineering, manual trades, domestic water engineering, horticulture and landscaping, agriculture and forestry, etc.
Available in a rigid or 360° swivelling version. The two systems can also be easily coupled to one another!

Cross-piece 180, 4 x IT, Rp 1/4, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Male branch tee »universal short«, L-shape, rotating 1/2,hose-Ø10,taper seat,Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Pipe double nipple 23, ET/ET, Black steel, R 3/8, Length 80.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

32 mm Samarium-Cobalt (SmCo)
SMCO POT VLAK 32X7
SKU: GM17108
Stock: 0
Holding force: 220 N
Height: 7 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Flat knurled thumb screw DIN 653 M4 x 20mm long steel strength 5.8 black oxide finished
Material: Steel, black oxide finish, tensile strength 5.8. Visible face precision turned. Produced from one piece and threaded over their full length (DIN designation A).
Article ID: 65423314

Round trapezoidal nut red brass 7 Tr.40 x 14 P7 double-thread right length 80mm outer diameter 80mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C). Tolerance zone 7H. Height = 2 x diameter.
Article ID: 64584000

Ratchet wheel pitch 4.71mm 120 teeth outside diameter 180mm
Material: C45Pb up to 80 mm diametre, above C45. Unhardened. Without Hub. Bores ISO H7. Tip angle 60°.

Article ID: 22771200

Push-in L-fitting, R 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Pressure regulator for water, incl. pressure gauge, R 2, Control range 0.2 - 2 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated piston valve or single-seated diaphragm valve and built-in strainer. Specially designed for use with water.
The device is also suitable for all other applications involving neutral non-sticky liquids, air and neutral non-flammable gases.

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 100, Stroke 5, G 3/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Throttle check valve, Discharge throttle (»C«) quick connector Hose 10/8, G 3/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ25, Stroke70, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Jaw coupling with ET, G 3/8, DN 8.5, Malleable cast iron, galvanised and yellow passivated, Operating pressure max. 10 bar
Universal standard coupling for compressed air lines on construction sites or in industry; standard type according to DIN 3489, used worldwide in a very wide range of applications.

- Robust couplings made of malleable iron, zinc plated and yellow chromated
- Chrome VI-free, with double safety lock
- 100% couple test and secure connection

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1 1/4, Length 40 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Polycarbonate container, for mist oiler and active charcoal filter »variobloc«, Size 1, G 1/4 and G 3/8

Hexagonal counter nut, M24x2, AF 28, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

Neodymium (NdFeB) 75 N
PM-HS-N-SG-D16x4.5xd3.5/6.6
SKU: GM17425
Stock: 130
Holding force: 75 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Flat knurled thumb screw DIN 653 M5 x 12mm long steel strength 5.8 black oxide finished
Material: Steel, black oxide finish, tensile strength 5.8. Visible face precision turned. Produced from one piece and threaded over their full length (DIN designation A).
Article ID: 65423317

Triple-strand sprocket DRT 08 B-3 1/2x5/16" 30 teeth material steel for taper bush type 2012
Material:: Steel C45, not hardened.General dimensions: B1 = 7,2 mm, B3 = 34,9 mm, c = 1,3 mm, r3 = 13 mm. Other dimensions: See the table.In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 13577130

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 50, Stroke 10, G 1/4, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure regulator for potable water, DVGW not necessary, incl. pressure gauge, Brass sieve cup, R 1, Control range 1.5 - 12 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

Filter »FUTURA« with metal container and viewing tube, 5 µm, Size 4, G 1, 1.5 - 16 bar, Temp. -10 °C to 50 °C, Fully-automatic
Filters with excellent flow rates in modern design.

Throttle check valve, Supply air throttle (»V«) quick connector Hose 10/8, G 3/8 PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ32, Stroke45, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Male branch elbow »universal short«, rotating, 1/4, hose-Ø 10, taper seat, Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Hexagonal counter nut, M42x2, AF 50, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Straight screw-in fitting, M18x1,5 o., Pipe exterior Ø 16 mm, PN max. 400 bar, A/F1 30, A/F2 27, galvanised steel, soft seal
Male connector, metric thread and soft seal, heavy type

Closing cap (hexagonal design), G 1/4, AF 16, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Round trapezoidal nut red brass Rg7 Tr.44 x 7 single-start right length 88mm outer diameter 80mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64334400

Neodymium (NdFeB) 105 N
PM-HS-N-SG-D20x6xd4.5/9.3
SKU: GM17426
Stock: 9
Holding force: 105 N
Height: 6 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Star knob screw similar to DIN 6336 type ST Ø32mm M6 x 10
Material: Thermoplast Polyamide PA. Threaded bolt: steel, zinc-plated, chromated blue.
Article ID: 66183210

Hexagonal trapezoidal nut steel C35Pb Tr.70 x 10 single-start left length 105mm wrench size 90mm
Material: Steel C35Pb. Tolerance zone 7H. Height = 1,5 x diameter. Attention: Steel nuts get very easily thightened on a spindle made from Steel or stainless steel. This nuts are only for clamping, manual adjustments or as fastening nut. Not suitable for drive systems.

Article ID: 64367000

Output shaft double sided for worm geared motor HMD/I and HMD/II gearbox size 085 diameter 35mm overall length 282mm
Material: Steel. To change the gearboxes HMD/I over from hollow shaft to solid shaft. The shaft is only pushed in and secured with the enclosed cover disc and mounting screw.

Article ID: 43808200

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 40, Stroke 80, G 1/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure regulator for potable water, DVGW not necessary, incl. pressure gauge, Brass sieve cup, R 1 1/4, Control range 1.5-12 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

Standard cylinder, ISO 15552, double-acting, Piston Ø 80, Stroke 160, G 3/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches can be mounted in two T-slots on the same side as the compressed air supply.
The version with a 125 mm bore is provided with fixing accessories on three sides as standard.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Tempered coupling DN 9, Exterior thread, Blocking valve, Brass, G 1/2 straight, Operating pressure max. 15 bar
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Angled screw-in fitting, R 1/2 o., Pipe exterior Ø 10 mm, PN max. 315 bar, Stainless steel 1.4571

Push-in T-fitting »Blue Series«, rotating, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Reducing sleeve 246, IT/ET, Rp 1, R 1/2, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

T-piece 130, IT/IT/IT, Rp 2, T-branch reducing Rp 1/2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galva.
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Screw-in hose connector, G 1/4 o., for hose I.D. 8 mm, AF 17, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Neodymium (NdFeB) 310 N
PM-HS-N-SG-D32x7xd5.5/11
SKU: GM17428
Stock: 100
Holding force: 310 N
Height: 7 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 12x9 mm, PN at 23 °C max. 8 bar, green, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions