Bevel gear made of steel module 6 25 teeth i=1:1
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears, with the same module and the same number of teeth.
Article ID: 36731600

Bush similar to DIN 1850 J (DIN 4379 C) sintered bronze borehole 5mm outer diameter 8mm length 10mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. After press-fitting them into a rigid bearing housing with a
mounting hole H7, these bearings have a bore of H7. Edges chamfered at
45°, at choice of the manufacturer. The concentricity tolerance refers
to d2. 1) no statement regarding the surface roughness according to DIN
3141 (prenorm) can be given due to the porous structure of the sintered
metal. Technical Data: Surface pressure: max. 35 N/mm², depending
on speed and diameter. Temperature range: -20°C to +120°C.Tolerances:
Inner diameter F7 / G7. Outer diameter s7. Length +/-0.1mm.

Article ID: 62330800

16 mm Ferrite
PM-BA-F-SG-D16x4.5
SKU: GM16403
Stock: 3
Holding force: 18 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Rod end GS DIN 12240-4 series K internal thread M42x2 left == Initial lubrication required before use ==
Material: Outer part: Zinc-plated. Boreholes up to 12mm: free-cutting steel, turned. From boreholes 14mm: Steel C22, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Special brass CuZn40Als. Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread either right-handed or left-handed. Heavy-duty rod ends for high radial and axial alternating loads. Steel on high-duty brass. Can be re-lubricated (only from size 5mm). Sliding speed up to 60 m/min. Initial lubrication required before use
Article ID: 63214000

timing bar XL 1/5" (5.08mm) 44 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A. Profile XL = 1/5" = 5.08 mm.
Article ID: 18094400

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ63, Stroke120,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure regulator for potable water, without DVGW, pressure gauge, R 1 1/2, Control range 1.5 - 6 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated diaphragm valve and built-in strainer. Specially designed for use in domestic water installations.
The device is also suitable for all other applications involving water, neutral
non-sticky liquids, air and neutral non-flammable gases.

Quick-connect coupling I.D. 19, Bright brass, G 3/4 IT, Operating pressure 0 - 35 bar, Med. / ambient temp. -20 °C to 100 °C
Single-sided blocking and quick connect coupling with extremely high flow performance.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Straight screw-in fitting, G 3/8 o., Pipe exterior Ø 14 mm, PN bar 630, A/F1 27, A/F2 24, galvanised steel
Male connector, parallel male thread, heavy type

5/2-way valve, Manual lever actuation, »4H«, engaging, G 1/4, Operating pressure 0 - 8 bar, Temperature range -20 °C to 70 °C
5/2- and 5/3-way valves
- Manually operated -

Bulkhead fitting, Exterior thread M28x1.5, Interior thread G 1/2, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Straight push-in connector, Plug nipple »Blue Series«, red., hose exterior Ø 10, plug nipple 12, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Double threaded nipple 245, red., R 2 1/2 ET, R 1 1/2 ET, black malleable iron fitting, oper. temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Bracket 92, 90°, IT/ET, Rp/R 3/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Bevel gear made of steel module 6 30 teeth i=1:1
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears, with the same module and the same number of teeth.
Article ID: 36732000

MAEDLER deep groove ball bearing single row inner diameter 8mm outer diameter 22mm width 7mm sealed on both sides
Single row deep groove radial ball bearings Material:
Bearing steel. - Standard ball bearings in high quality. - Most common
bearing type. - Usable for high speed. - Insensitive in use and
maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or
with contacting rubber seals 2RS. Temperature range: -20°C to +90°C
(caused by type of lubrication), short-term up to 110°C. Other
versions or other bearing types on request.
Article ID: 608-2RS-MAE

20 mm Ferrite
PM-BA-F-SG-D20x6
SKU: GM16404
Stock: 0
Holding force: 30 N
Height: 6 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Ball head precision levelling adjuster MN 686.4 60-26.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For non-parall surfaces up to 4° slope. Lower overall height with short adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68647000

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ63, Stroke120, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure regulator for potable water, without DVGW, pressure gauge, R 2, Control range 1.5 - 6 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated diaphragm valve and built-in strainer. Specially designed for use in domestic water installations.
The device is also suitable for all other applications involving water, neutral
non-sticky liquids, air and neutral non-flammable gases.

Quick-connect coupling I.D. 19, Bright brass, G 1 IT, Operating pressure 0 - 35 bar, Med. / ambient temp. -20 °C to 100 °C
Single-sided blocking and quick connect coupling with extremely high flow performance.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

L-multi-distributor »Blue Series«, 3-fold, rotating, G 1/2 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

5/2-way valve, Manual lever actuation, »4H«, engaging, G 1/8, Operating pressure 0 - 8 bar, Temperature range -20 °C to 70 °C
5/2- and 5/3-way valves
- Manually operated -

Mini ball valve, Smooth surface, nickel-plated brass, Medium temp.-10 °C to 70 °C (short term 90 °C), G 1/4 ET, DN8, PN max.10 bar

Push-in T-fitting »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Quick relief valve, G 1/4, AF1 19, AF2 19, AF3 19, Operating pressure max. 12 bar, Operating temperature -20 °C to 80 °C

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1 1/4, Length 60 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Bevel gear made of steel module 6 40 teeth i=1:1
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears, with the same module and the same number of teeth.
Article ID: 36732600

Shaft collar DIN 705 A set screw with slot bore 16mm zinc plated
Light-duty series. With set screw DIN EN 27 434 made from steel, zinc-plated. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62388016

Rod end GT DIN 12240-4 series K internal thread M42x2 right maintenance-free
Material:
Outer part: Zinc-plated. Boreholes up to 12mm: free-cutting steel, turned. From boreholes 14mm: Steel C22, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K.

Thread either right-handed or left-handed. Heavy-duty rod ends for high radial and axial alternating loads.
Steel on PTFE-lining.
Maintenance-free.
Sliding speed up to 10 m/min.
Article ID: 63264000

25 mm Ferrite
PM-BA-F-SG-D25x7
SKU: GM16405
Stock: 0
Holding force: 40 N
Height: 7 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Spoked handwheel DIN 950 stainless steel 1.4401 version B/G with handle diameter 160mm
Material: Material: Wheel body: Cast stainless steel 1.4401. Rim turned and polished. At version B/G: Handle stainless steel 1.4404. Version B/A: Without handle and thread. Version B/G: With fixed handle. Acid-resistant A4-quality. Easy to clean. Dimensions almost according to DIN 950. Keyway available at extra charge.
Article ID: 67099816

Pressure gauge, 0 - 4 bar/50 psi, 80 mm Ø, for plugging, for handheld digital tyre gauge

Quick-connect coupling I.D. 19, Bright brass, Sleeve I.D. 16, Operating pressure 0 - 35 bar, Med. / ambient temp. -20 °C to 100 °C
Single-sided blocking and quick connect coupling with extremely high flow performance.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Bushing 240, reducing, IT/IT, Rp 1 1/4, Rp 3/8, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Pressure regulator »FUTURA-mini«, incl. standard pressure gauge, Size 0, G 1/4, Input pressure max. 12 bar, 0.1 - 4 bar
Diaphragm pressure regulators with self-relieving design and with excellent flow rates in modern design.
The regulator knob can be latched.

Pressure regulator for potable water, DVGW not necessary, incl. pressure gauge, Brass sieve cup, R 1/2, Control range 1.5 - 12 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

Mini ball valve, Smooth surface, nickel-plated brass, Medium temp.-10 °C to 70 °C (short term 90 °C), G 3/8 IT, DN8, PN max.10 bar

Adjustable male connector, M10x1.0 o., Pipe exterior Ø 6, PN 315, a/f1 14, a/f2 14, galvanised steel

Jaw coupling with ET, G 3/4, with brass seal, Malleable cast iron, galvanised / yellow passivated, Operating pressure max. 10 bar
Universal standard coupling for compressed air lines on construction sites or in industry; standard type according to DIN 3489, used worldwide in a very wide range of applications.

- Robust couplings made of malleable iron, zinc plated and yellow chromated
- Chrome VI-free, with double safety lock
- 100% couple test and secure connection

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1, Length 120 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Bevel gear made of steel module 8 20 teeth i=1:1
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears, with the same module and the same number of teeth.
Article ID: 36771100

Turnbuckle similar DIN 1479 steel zinc-plated thread M10 length 45mm
Material: St37 DIN 1629, either untreated or zinc-plated.

M6 to M16 with overlapping thread, from M20 middle part relieved.
Some turnbuckle nuts are supplied with cross-holes, according to DIN 1479 as at 09/2005, which serve to check the minimum thread engagement.

*Threads: one side right-hand thread, other side left-hand thread.


Article ID: 65386000

Rod end GT DIN 12240-4 series K internal thread M42x2 left maintenance-free
Material:
Outer part: Zinc-plated. Boreholes up to 12mm: free-cutting steel, turned. From boreholes 14mm: Steel C22, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K.

Thread either right-handed or left-handed. Heavy-duty rod ends for high radial and axial alternating loads.
Steel on PTFE-lining.
Maintenance-free.
Sliding speed up to 10 m/min.
Article ID: 63274000

32 mm Ferrite
PM-BA-F-SG-D32x7
SKU: GM16406
Stock: 0
Holding force: 80 N
Height: 7 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Gear rack made of steel module 2 tooth width 20mm height 20mm length 1000mm teeth induction hardened
Material: Specially treated bright steel C45KG. Tooth area induction hardened, 54 +4 HRC. Precisely Straightened. Teeth milled in quality 8. But the hardening sets the tooth quality to 10-11. Cross-section tolerance h11 = -1/10 to -2/10 depending on size. Straight teeth. Pressure angle 20°. Tooth quality 8d25 modelled on DIN 3962, 3967, 3968. The teeth on the gear racks are manufactured using an overhead milling cutter. This leads to negative tolerances for dimension a and h0: Module 2: -0,2 mm. Module 3 to 4: -0,3 mm. Module 5: -0,4 mm. * Length = Nominal length. The real length is roughly one multiple of the pitch.

Article ID: 24188605

Solid-Disk handwheel 323 version B/G with Revolving handle diameter 250mm
Material: Aluminium gravity die-cast, plastic coated, black, textured finish. Hub machined. Rim turned on all sides. The rim is machined before coating, thus it is perfectly concentric. Version B/G: Without keyway. Version N/G: With keyway DIN 6885-1.
Article ID: 67091700

Pressure gauge, 0 - 12 bar/170 psi, 80 mm Ø, for plugging, for handheld digital tyre gauge

Quick-connect coupling I.D. 19, Bright brass, Sleeve I.D. 19, Operating pressure 0 - 35 bar, Med. / ambient temp. -20 °C to 100 °C
Single-sided blocking and quick connect coupling with extremely high flow performance.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Female hinge model for articulated male hinge model, ISO 15552, ISO 21287, Ø40, 4 screws, 1 bolt and retainer
Female hinge model

Pressure regulator »FUTURA-mini«, incl. standard pressure gauge, Size 0, G 1/4, Input pressure max. 12 bar, 0.5 - 8 bar
Diaphragm pressure regulators with self-relieving design and with excellent flow rates in modern design.
The regulator knob can be latched.

Pressure regulator for potable water, without DVGW, pressure gauge, R 1/2, Control range 1.5 - 12 bar, Input pressure max. 25 bar
Pressure regulator with pressure-reduced single-seated piston valve or single-seated diaphragm valve and built-in strainer. Specially designed for use with water.
The device is also suitable for all other applications involving neutral non-sticky liquids, air and neutral non-flammable gases.

Push-in T-fitting »metallica«, rotating, R 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Adjustable male connector, M16x1.5 o., Pipe exterior Ø 12, PN 315, a/f1 22, a/f2 22, galvanised steel

Push-in T-fitting »metallica«, rotating, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Straight push-in connector, Plug nipple reducing 6 mm, »click-clock«, for hose exterior Ø 4 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Locknut DIN 1804 type W M14x1.5 black finishing
Material: steel, black oxide finish, unhardened, unground.At these nuts, the stepped face with Ø d3 shall always be used as the bearing face.From size M45x1.5, the nuts have 6 slots.
Article ID: 65261400

40 mm Ferrite
GM16407
SKU: GM16407
Stock: 0
Holding force: 125 N
Height: 8 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Slide set DZ 0301 slide length 610mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Low slide profile (only 35.3mm). Bracket mount for electrical cabinets on request. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings. Ordering details: e.g.: Product no. 649 034 12, Slides 0301
Article ID: 64903424

Solid-Disk handwheel 323 version N/G with revolving handle diameter 250mm with bore 22H7 and keyway
Material: Aluminium gravity die-cast, plastic coated, black, textured finish. Hub machined. Rim turned on all sides. The rim is machined before coating, thus it is perfectly concentric. Version B/G: Without keyway. Version N/G: With keyway DIN 6885-1.
Article ID: 67091701