Slide set DZ 5417 slide length 300mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in the closed position. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings. Ordering details: e.g.: Product no. 649 049 30, Slides 5417
Article ID: 64904930

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 10x8 mm, PN at 20 °C max. 7 bar, black, Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Service unit 2-part »multifix«, PC container, Protective cage, Size 3, G 1/2, Input pressure max. 16 bar, Control range 0.5-10 bar
Two-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator and a proportional lubricator.

Pipe double nipple, G 1 1/4, Length 120 mm, Working pressure max. 10 bar, Medium / ambient temperature max. 90 °C, Bright brass

Round cylinder TP (ISO 6432) double-acting, Piston Ø 16, Stroke 160, M5, Working pressure max. 10 bar, Temp. -10 °C to 60 °C
Inexpensive standard version with aluminum pipe and magnet piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight screw-in fitting, R 3/4 o., Pipe exterior Ø 22 mm, PN max. 160 bar, AF1 36, AF2 32, galvanised steel
Male connector, conical male thread acc. to ISO 7-1, light type

Worm thread hose clamp, Stainless steel 1.4401 (W5), Hexagonal screw AF 7, Clamping range 90.0 - 110.0 mm, Belt width 9.0 mm
Worm drive type.

For all standard applications where high clamping forces are normally distributed.

Hexagon-head screw a/f 7, with integrated cross-tip, Stainless steel 1.4401 (W 5).

Reducing fitting, Sealing cone, Nut M26x1.5 i., Pipe exterior Ø1 18 mm, Pipe exterior Ø2 15 mm, PN max. 315 bar, galvanised steel
Reducer, with cone seal, light type

Straight screw-in fitting, »value line«, G 1/8 o., for hose 10/8 mm, AF 14, Operating pressure max. 18 bar, nickel-plated brass
Straight connectors
Nickel-plated brass, »value line« Series

25 mm Neodymium (NdFeB)
PM-BA-N-SG-D25x7
SKU: GM17407
Stock: 0
Holding force: 200 N
Height: 7 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Precision single universal joint WEN with needle bearing DIN808 bore 35H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel 35SMnPb10, Bearing Parts 18NiCrMo5Pb. Max. Operating Angle 45°. The needle-bearing universal joints have almost zero backlash, high accuracy and good turning properties. These special needle-rollers without cage can take high loads even at large operating angles. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - which guarantees an extremely long service life. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63117000N

Slide rail DZ 9301 slide length 356mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold by piece (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Lengths to 1.5 meters. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles ( to 217 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905114

Pressure regulator for potable water, DVGW tested, pressure gauge, R 1/2, Control range 1.5 - 6 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated diaphragm valve and built-in strainer. Specially designed for use in domestic water installations.
The device is also suitable for all other applications involving water, neutral
non-sticky liquids, air and neutral non-flammable gases.

Compact cylinder »ACP«, double-acting, Piston Ø 50, Stroke 45, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cylinder »ACP«, double-acting, Piston Ø 100, Stroke 40, Connection G 1/4, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Multi-base plate for 3/2-way valve pneumatic / electropneumatic, 3 valve positions, for valves connection G 1/8, G 1/4
Aluminium alloy manifold bases 6061-T6 for 2 to 8 valve positions.

GEKA angled hose piece, 360° rotating, bright brass, I.D. 32, Operating pressure max. 40 bar, Medium/ambient temp. -10 °C to 90 °C
Claw couplings (claw distance: 40 mm) made of brass for water, industrial, mortar, suction and discharge hoses. Suitable for a wide range of applications, e.g. industrial plant engineering, civil and structural engineering, environmental engineering, manual trades, domestic water engineering, horticulture and landscaping, agriculture and forestry, etc.
Available in a rigid or 360° swivelling version. The two systems can also be easily coupled to one another!

Hexagonal counter nut, G 1 1/4, AF 50, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Pressure gauge- screw connection, G 1/2 i., Pipe exterior Ø 8 mm, PN max. 630 bar, AF1 19, AF2 27, galvanised steel
Pressure gauge fitting, parallel female thread, heavy type

L-multi-distributor »Blue Series«, 2-fold, rotating, R 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Double threaded nipple 245, ET/ET, red., R 3/8, R 1/4, oper. temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Bevel gear made of steel module 5 40 teeth i=1:1 milled
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears, with the same module and the same number of teeth.
Article ID: 36212600

32 mm Neodymium (NdFeB)
PM-BA-N-SG-D32x7
SKU: GM17408
Stock: 11
Holding force: 350 N
Height: 7 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Precision single universal joint WE DIN808 simple bore 35H7 material steel total length 140mm outer diameter 70mm
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63127000

Precision levelling adjuster MN 686.1 60-39.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For parall surfaces. Larger overall height with more adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68618000

Pressure regulator for potable water, DVGW tested, pressure gauge, R 3/4, Control range 1.5 - 6 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated diaphragm valve and built-in strainer. Specially designed for use in domestic water installations.
The device is also suitable for all other applications involving water, neutral
non-sticky liquids, air and neutral non-flammable gases.

Push-in T-fitting, L-shape, rotating, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Handheld tyre gauge, double-sided garage connector, Calibrated, 0-12 bar/170 psi, Plug-in nipple I.D. 7.2
These pressure gauges are effectively protected against shock and impact by means of a free-standing plastic cap. They can be loaded against gauge pressure and up to the maximum scale value.
With push-in plug for DN 7.2 coupling.

Multi-base plate for 5/2-5/3-way valve pneumatic / electropneumatic, 3 valve positions, Valve connection G 1/8, G 1/4
Aluminium alloy manifold bases 6061-T6 for 2 to 8 valve positions.

Double threaded nipple, R 3/4 o., R 1 1/4 o., Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Straight screw-in fitting, R 1/2 o., Pipe exterior Ø 8 mm, PN max. 315 bar, AF1 17, AF2 22, galvanised steel
Male connector, conical male thread acc. to ISO 7-1, light type

Rem. double threaded nipple, conical sealing, R 1/4 o., R 3/8 o., Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Air gun with short nozzle, Plastic, Temperature range -20 °C to 50 °C, PN max. 10 bar, G 1/4 IT
For blowing out and cleaning machines, engines, bearings, sliding surfaces, bores of all kinds, hollow parts, moulds, etc.

Bushing 240, reducing, IT/IT, Rp 1/2, Rp 1/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Flanged bush similar to DIN 1850 V (DIN 4379 F) sintered bronze bore 8mm outer diameter 12mm flange diameter 16mm length 16mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. Edges chamfered at 45°, at choice of the manufacturer. The
concentricity tolerance refers to d2. 1) no statement regarding the
surface roughness according to DIN 3141 (prenorm) can be given due to
the porous structure of the sintered metal. Technical Data: Surface
pressure: max. 35 N/mm², depending on speed and diameter. Temperature
range: -20°C to +120°C. Dimension r: For bores 3 - 8 mm = 0.3 mm, bores
9 - 22 mm = 0.6 mm, bores 25 - 40 mm = 0.8 mm Tolerances: Inner
diameter d1: F8 / G8. Outer diameter d2: s8. Flange diameter d3: js13.
Length b1:+/-0.1mm.Flange thickness b2: js14.

Article ID: 62351400

10 mm Ferrite
PM-BA-F-SG-D10x4.5
SKU: GM16401
Stock: 0
Holding force: 4 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Precision single universal joint WE DIN808 bore 35H7 with keyway DIN 6885-1 tolerance JS9 on both sides steel
Material: Steel. Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - this guarantees an extremely long service life. All contact surfaces are hardened, ground and lapped. These universal joints are used at high torques and high speeds up to max. 800 rpm. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63127000N

Slide set DZ 5321 SC slide length 300mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Self-close. Hold-in in closed position. Bracket Mount for electrical cabinets on request. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk / 6mm countersunk Euro screw. Use all mounting positions to achieve the max. load rating. Ordering details: e.g.: Product no. 649 042 30, Slides 5321 SC
Article ID: 64904230

Pressure regulator for potable water, DVGW tested, pressure gauge, R 1, Control range 1.5 - 6 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated diaphragm valve and built-in strainer. Specially designed for use in domestic water installations.
The device is also suitable for all other applications involving water, neutral
non-sticky liquids, air and neutral non-flammable gases.

Spray gun straight spray pipe, Plastic, Plug-in nipple I.D. 7.2, PN max. 10 bar. Plastic cup 0.7 l, matt transparent
With plastic cup, capacity approx. 0.7 litres, matte-transparent.

Operating pressure: Approx. 2 to 6 bar
Connection: Push-in plug for DN 7.2 coupling

The spray fan of these guns can be adjusted with a nozzle according to requirements:
Simply loosen the lock nut, adjust the nozzle and re-tighten the nut.

Quick-connect coupling I.D. 19, Bright brass, G 3/4 ET, Operating pressure 0 - 35 bar, Med. / ambient temp. -20 °C to 100 °C
Single-sided blocking and quick connect coupling with extremely high flow performance.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Quick relief valve, G 1/2, AF1 26, AF2 26, AF3 26, Operating pressure max. 12 bar, Operating temperature -20 °C to 80 °C

Screw-in hose connector R 1 1/4 o., for hose I.D. 38 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Push-in L-fitting »Blue Series« long, rotating, G 1/2 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Double hose connector, reduced, for hose I.D. 9,13 mm, Brass CW614N, Max. working pressure 16 bar, Max. medium/ambient temp. 90 °C

High performance silencer, Aluminium, G 1/8, Working pressure 0 - 10 bar, Operating temperature -10 °C to 70 °C

Reducing nipple, long type, M3 o., M5 i., AF 7, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Flanged bush similar to DIN 1850 V (DIN 4379 F) sintered bronze bore 12mm outer diameter 15mm flange diameter 18mm length 12mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. Edges chamfered at 45°, at choice of the manufacturer. The
concentricity tolerance refers to d2. 1) no statement regarding the
surface roughness according to DIN 3141 (prenorm) can be given due to
the porous structure of the sintered metal. Technical Data: Surface
pressure: max. 35 N/mm², depending on speed and diameter. Temperature
range: -20°C to +120°C. Dimension r: For bores 3 - 8 mm = 0.3 mm, bores
9 - 22 mm = 0.6 mm, bores 25 - 40 mm = 0.8 mm Tolerances: Inner
diameter d1: F8 / G8. Outer diameter d2: s8. Flange diameter d3: js13.
Length b1:+/-0.1mm.Flange thickness b2: js14.

Article ID: 62352000

13 mm Ferrite
PM-BA-F-SG-D13x4.5
SKU: GM16402
Stock: 30
Holding force: 10 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Rod end GS DIN 12240-4 series K internal thread M42x2 right == Initial lubrication required before use ==
Material: Outer part: Zinc-plated. Boreholes up to 12mm: free-cutting steel, turned. From boreholes 14mm: Steel C22, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Special brass CuZn40Als. Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread either right-handed or left-handed. Heavy-duty rod ends for high radial and axial alternating loads. Steel on high-duty brass. Can be re-lubricated (only from size 5mm). Sliding speed up to 60 m/min. Initial lubrication required before use
Article ID: 63204000

timing bar AT3 72 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16397200

Round cylinder, ISO 6432, double-acting, Magnet, Piston Ø 25, Stroke 125, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 80°C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure regulator for potable water, DVGW tested, pressure gauge, R 1 1/4, Control range 1.5 - 6 bar, Input pressure max. 16 bar
Pressure regulator with pressure-reduced single-seated diaphragm valve and built-in strainer. Specially designed for use in domestic water installations.
The device is also suitable for all other applications involving water, neutral
non-sticky liquids, air and neutral non-flammable gases.

Quick-connect coupling I.D. 19, Bright brass, G 1 ET, Operating pressure 0 - 35 bar, Med. / ambient temp. -20 °C to 100 °C
Single-sided blocking and quick connect coupling with extremely high flow performance.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Double threaded nipple, Hexagonal, G 2, AF 63, Working pressure max. 20 bar, Stainless steel 1.4408

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 12, Stroke 10, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Straight screw-in fitting, R 3/8 o., Pipe exterior Ø 15 mm, PN max. 315 bar, AF1 27, AF2 24, galvanised steel
Male connector, conical male thread acc. to ISO 7-1, light type

Push-in L-fitting »Blue Series«, rotating, Rc/R 1/8 i./o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Elbow 2, 90°, long, Rp 1 1/2 IT, Rp 1 1/2 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Screw-on hose connector, G 1/8 i., for hose I.D. 4 mm, AF 14, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C