Pressure regulator for potable water, DVGW tested, incl. pressure gauge, Transparent sieve cup, R 1, Control range 1.5 - 6 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

Push-in L-fitting »Blue Series«, rotating, G 3/8 o., for hose exterior Ø 16 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series« long, rotating, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Throttle check valve »Blue Series«, Supply air throttle, G 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Piston rod nut, for round cylinder ISO 6432, Compact / standard cylinder, Piston Ø 25/32-40/32, Piston rod thread M10x1.25
Rod nut

8 mm Neodymium (NdFeB)
PM-BA-N-SG-D8x4.5
SKU: GM17402
Stock: 19
Holding force: 13 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Clevis joint similar DIN 71752 size 5 x 10 type SL right handed aluminum black anodized
Material: Clevis and bolt aluminium, anodized black.With SL-Retainer from steel, bright zinc plated. Thread: Gewindeausführung rechts = thread right-handed.
Article ID: 63766403

Worm shaft made of steel C45 module 3 single-thread right hand
Material: Steel C45, whirled, with centring holes. Single-thread worms to be paired with single-thread worm gears. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°.

Article ID: 31000100

Glycerine pressure gauge, bracket fastening, triangle front ring, Connection, rear, centric, G 1/4, Meas. range -1 / +5 bar, Ø 63
Bourdon-tube pressure gauge in standard design, with clamp fixing.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Storz reducer, Aluminium, Storz size 38/25-D, Tappet distance 51/31 mm, Operating pressure max. 16 bar, Temp. -40 °C to 110 °C
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

3-way ball valve, L-hole, nickel-plated brass, Medium / ambient temp. -15 °C to 100 °C, Rp 1 1/2, DN 40, PN max. 16 bar
The medium can enter via any of the ports to allow several switching variants.

3-way ball valves for diverting media.

Male elbow, M8x1.0 tapered o., Pipe exterior Ø 5 mm, PN max. 100 bar, a/f1 12, a/f2 9, galvanised steel

Pressure regulator »Standard-mini«, incl. pressure gauge and control panel nut, G 1/8, Input pressure max. 25 bar, 0.5 - 10 bar
Compact, reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the knob down.

Throttle check valve »Blue Series«, Discharge throttle, R 1/4 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

L screw-in fitting, ET conical, R 1/8, for hose 8/6 mm, AF 12, Working pressure max. 18 bar, nickel-plated brass

Throttle check valve »Blue Series«, Discharge throttle, G 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, G 1/8 o., for hose 8/6 mm, AF 14, Brass
For the installation of plastic tubing.

Round trapezoidal nut steel C35Pb Tr.52 x 8 single-start right length 78mm outer diameter 90mm
Material: Steel C35Pb.

Tolerance zone 7H.

Height = 1,5 x diameter.

Attention:
Steel nuts get very easily thightened on a spindle
made from Steel or stainless steel.
This nuts are only for clamping, manual adjustments or as fastening nut.
Not suitable for drive systems.

Article ID: 64305200

10 mm Neodymium (NdFeB)
PM-BA-N-SG-D10x4.5
SKU: GM17403
Stock: 70
Holding force: 25 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Hexagon nut DIN 934 brass Ms60 thread M8 right handed
Material: Brass CuZn40 (Ms60).Hexagon nuts according to the old standard DIN 934 with metric ISO thread.The standard DIN 934 was replaced by DIN EN ISO 4032 / 8673. Some of these nuts have different outer dimensions (width across flats and height). But the nuts DIN 934 are still used very often.
Article ID: 65270800

timing bar AT5 58 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16695800

Sprocket KRR with hub 10 B-1 5/8x3/8" 25 teeth material stainless steel 1.4305
Material: Stainless steel 1.4305. Teeth milled, pre-bored. General dimensions: B1 = 9,1 mm, c = 1,6 mm, r3 = 16 mm. Other dimensions: See the table.

Article ID: 10699125

5/2-way valve, manual, Rotating handle, short, monostable, Connec. G 1/8, Operating pre. 2.5-10 bar, Operating temp. -10°C to 60°C

Pressure regulator for potable water, DVGW tested, incl. pressure gauge, Transparent sieve cup, R 1 1/4, Control range 1.5 - 6 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

2/2-way solenoid valve »2KS«, Stainless steel, NO, pilot operated, 230 V, 50 Hz, Medium temp. max. 80°C/90°C, G 1, PN 0.5 - 7 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Polycarbonate container, incl. O-ring, with semi-automated bleeder valve, for »multifix«, Size 3, G 1/2 and G 3/4 and Size 5, G 1

Pressure regulator »Standard-mini«, incl. pressure gauge and control panel nut, G 1/8, Input pressure max. 25 bar, 0.5 - 16 bar
Compact, reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the knob down.

T-fitting, Pipe exterior Ø 6 mm, PN max. 315 bar, AF1 14, AF2 12, galvanised steel
Branch tee, light type

Straight push-in fitting »Blue Series«, G 1/2 i., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series« long, rotating, R 3/8 o., for hose exterior Ø 16 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Bushing with exterior hexagonal, G 3/8, AF 22, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

13 mm Neodymium (NdFeB)
PM-BA-N-SG-D13x4.5
SKU: GM17404
Stock: 94
Holding force: 60 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Hexagon nut DIN 6331 with collar steel strength 10 thread M12 right hand
Material: Heat-treated steel, tensile strength 10. The collar on the nut means no separate washer is required.

Article ID: 65331200

Ball head precision levelling adjuster with locknut MN 686.9 60-26.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For non-parall surfaces up to 4° slope. Larger overall height with more adjustment travel. With lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68697000

Bevel gear made of steel module 5 20 teeth i=1:5 milled
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).With crowned, milled teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module, with a different number of teeth of the same ratio.
Article ID: 36215200

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 10x8 mm, PN at 20 °C max. 7 bar, natural (milky), Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Pressure regulator for potable water, DVGW tested, incl. pressure gauge, Transparent sieve cup, R 1 1/2, Control range 1.5 - 6 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

2/2-way solenoid valve »2KS«, Stainless steel, NO, pilot operated, 24 V DC, Medium temp. max. 80 °C / 90 °C, G 1, PN 0.5 - 7 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Plug nipple with pressure eliminator, Series A, I.D. 13, hardened, galvanised steel, G 1/2 IT, PN max. 250 bar
Acc. to ISO 7241-1, A Series.

This coupling series combines an extremely small pressure drop with maximum hydraulic power transmission.
Interchangeable with all couplings and plugs manufactured according to the above standard.
The patented pressure eliminator permits disconnection even if back pressure has built up (up to 200 bar).
The pressure eliminator can be used in all applications where there is a risk of pressure build-up after the line has been separated. It allows effortless connection under pressure.
The mating part must be pressureless in order for the eliminator to function optimally.

Areas of application: Agricultural machines, construction machines, municipal engineering, transportation engineering, industrial plant.

Round cylinder, ISO 6432, double-acting, Magnet, Piston 10, Stroke 10, M5, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled screw-in fitting, R 1/4 o., Pipe exterior Ø 12 mm, PN max. 315 bar, AF1 22, AF2 17, galvanised steel
Male elbow, conical male thread acc. to ISO 7-1, light type

Sintered bronze silencer, flat, G 1/2 o., Operating pressure max. 10 bar, Operating temperature -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

Hinge pin clamp, Stainless steel 1.4301 (W4), Clamping range 79.0 - 85.0 mm, Belt width 25.0 mm, rec. tightening torque 20.0 Nm

T-hose fitting supports, for hose I.D. 16 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

16 mm Neodymium (NdFeB)
PM-BA-N-SG-D16x4.5
SKU: GM17405
Stock: 8
Holding force: 95 N
Height: 4.5 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Lifting eye bolt M6 x 13 stainless steel A4 casted
Material: Stainless steel A2 or stainless steel A4, cast, polished.Cost-effective version for many fastening applications, for example in household and garden for light tensioning.Not permitted as lifting device or in safety-relevant areas.Temperature range: -20°C to +200°C. Note: These ring bolts are not according to DIN 580. The load capacity is not like DIN. So, theses parts may only be used for light loads in responsibility of the customer, and never for safety-relevant applications. Depending on the casting company, these parts are marked with the size of thread and / or the manufacturer symbol.

Article ID: 65458506

chain-stretcher for double roller chain 3/4X7/16" , set of 14052701 + 14080300
Material: Housing sintered steel or grey cast iron GG20, lever St52, sprocket made of steel. This tensioning element, a continually-tensioning torsion element, prolongs the service life of chain and belt drives by at least 30%, and radically reduces maintenance and repair work. The unique operating principle of this spring offers a long tensioning distance, especially as the lever can be pre-tensioned by up to 30° in both directions. The permanent torsion force does not only automatically compensate the chain elongation, the rubber mounted element also dampens vibrations and shocks in the entire drive. Other advantages: chain track adjustable, rubber suspension, adjustable at an angle of 360º, tensioning pressure steplessly adjustable from 'normal' to 'hard'. Can be used for both tensioning directions.

Article ID: 14052700

timing bar T5 45 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16294500

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 10x8 mm, PN at 20 °C max. 7 bar, blue, Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Pressure regulator for potable water, DVGW tested, incl. pressure gauge, Transparent sieve cup, R 2, Control range 1.5 - 6 bar
Diaphragm pressure regulators with pressure-reduced single-seated valve and built-in strainer.
These pressure regulators, which are independent of inlet pressure, protect domestic water installations against
excessive supply pressure. They can also be used for commercial or industrial purposes providing their
specification is adequate.

Short stroke cylinder, double-acting, Magnet, Piston Ø 80, Stroke 70, G 1/4, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Safety ball valve, lockable, without venting hole, nickel-plated brass, Operating temp. max. 170°C, Rp 1/2, DN 15, PN max. 65 bar
2/2-way safety ball valves made of nickel-plated brass.
The ball valve can be locked manually.
Full bore, heavy-duty type.

Round cylinder, ISO 6432, double-acting, Magnet, Piston Ø 8, Stroke 50, M5, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight push-in bulkhead connector »Blue Series«, M24x2.0, for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series«, rotating, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series« long, rotating, R 3/8 o., for hose exterior Ø 14 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, G 1/8 o., for hose 6/4 mm, AF 14, Brass
For the installation of plastic tubing.

20 mm Neodymium (NdFeB)
PM-BA-N-SG-D20x6
SKU: GM17406
Stock: 16
Holding force: 140 N
Height: 6 mm
Material housing: Galvanized steel
Compact flat magnet systems available in neodymium, samarium cobalt, ferrite and AlNiCo. Suitable for gluing. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without an air gap.

Deliverable from stock
Available in various sizes
Available with extra strong magnet

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical, flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Magnetic short circuit

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into steel. Always maintain a minimum distance between the brass shell of the pot magnet and the steel. Contact Goudsmit for specific recommendations.
E-mail or call +31 (0)40 221 3283.

Rubber-metal MGE diameter 20mm height 25mm inner thread M6
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Steel, zinc plated. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68510207

Precision single universal joint WEN with needle bearing DIN808 simple bore 35H7 material steel total length 140mm outer diameter 70mm
Material: Steel 35SMnPb10, Bearing Parts 18NiCrMo5Pb. Max. Operating Angle 45°. The needle-bearing universal joints have almost zero backlash, high accuracy and good turning properties. These special needle-rollers without cage can take high loads even at large operating angles. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - which guarantees an extremely long service life. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63117000