Slide rail DZ 9308 single rail right hand slide length 559mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold singly (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Single slides available (left or right). Lengths to 1.5 meters. Lock-in in closed position. Lock-out in open position. Front lever lock releaze. Only for vertical mounting. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles (to 180 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note These slides are available separately. To lock both sides, you need a left slide 9308 and a right slide 9308. If you want to lock only one side, you can combinate it with a slide 9301-E. Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905422

Ball valve, Manual lever, Basic design, IT/IT, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 2, DN 50, PN max. 25 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 2.5 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Hydraulic coupling locking on both sides, Bright brass, G 1/8 IT, I.D. 4.3, Operating pressure max. 250 bar, Temp. -20°C to 100°C
Hydraulic couplings, both sides sealing, for liquid media acc. to ISO 7241, B Series.

Areas of application: machine and plant engineering, manufacturing industry, chemical / pharmaceutical industry, automotive, food technology.

Full stroke safety valve DN 8, Brass, Operating temperature -25 °C to 180 °C, G 1/4, AF 20, Trigger pressure 44.8 bar, Type tested
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Replacement seal for Storz coupling, made of FKM, Storz size 25-D, Tappet distance 31 mm

Pressure gauge connection nipple made of brass, G 1/4 bushing, G 1/2 taps, PN 600 bar

Coupling nut, M26x1.5, Pipe exterior Ø 18 mm, PN max. 315 bar, Stainless steel 1.4571

Angled screw-on fitting »value line«, G 1/8, for hose 6/4 mm, AF 10, Operating pressure max. 18 bar, nickel-plated brass
Union elbows
Nickel-plated brass, »value line« Series

Trapeziodal-threaded spindle DIN 103 Tr.18 x 4 x 1000mm long single-start right material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099018

Adjusting ring DIN 705 A set screw with slot bore 60mm stainless steel 1.4305
Material: 1.4305.Light-duty series. With set screw DIN EN 27 434 made from stainless steel.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC,
Article ID: 62399060

Flanged bush similar to DIN 1850 V (DIN 4379 F) sintered bronze bore 12mm outer diameter 17mm flange diameter 22mm length 12mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. Edges chamfered at 45°, at choice of the manufacturer. The
concentricity tolerance refers to d2. 1) no statement regarding the
surface roughness according to DIN 3141 (prenorm) can be given due to
the porous structure of the sintered metal. Technical Data: Surface
pressure: max. 35 N/mm², depending on speed and diameter. Temperature
range: -20°C to +120°C. Dimension r: For bores 3 - 8 mm = 0.3 mm, bores
9 - 22 mm = 0.6 mm, bores 25 - 40 mm = 0.8 mm Tolerances: Inner
diameter d1: F8 / G8. Outer diameter d2: s8. Flange diameter d3: js13.
Length b1:+/-0.1mm.Flange thickness b2: js14.

Article ID: 62352200

125 mm White
TII0125R300601
SKU: TII0125R300601
Stock: 0
Thickness: 0.6 mm
Roll length: 30 m
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Spoked handwheel DIN 950 stainless steel 1.4401 version B/G with handle diameter 200mm
Material: Material: Wheel body: Cast stainless steel 1.4401. Rim turned and polished. At version B/G: Handle stainless steel 1.4404. Version B/A: Without handle and thread. Version B/G: With fixed handle. Acid-resistant A4-quality. Easy to clean. Dimensions almost according to DIN 950. Keyway available at extra charge.
Article ID: 67099820

Solid-Disk handwheel similar to DIN 950 made of aluminium diameter 225mm
Material: Aluminium, rim of wheel ground and with high-gloss finish.  Outer diameter and hub length according to DIN 950. At some products, the bore diameter is a special size, not like DIN 950.Bigger bore or keyway available at extra charge.
Article ID: 67032200

Ball valve, Manual lever, Basic design, IT/ET, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 2, DN 50, PN max. 25 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0-25 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Locking screw Hexagonal socket without flange G 1 1/4nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Full stroke safety valve DN 8, Brass, Operating temperature -25 °C to 180 °C, G 1/4, AF 20, Trigger pressure 47 bar, Type tested
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Replacement seal in FKM, for GEKA stainless steel couplings of series »GEKA plus«, Temperature range -10 °C to 150 °C

Elbow 1, 90°, long, Rp 3/4 ET, R 3/4 ET, black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Reducing sleeve 246, IT/ET, Rp 2, R 1, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Angled screw-in fitting »value line«, R 1/4 o., for hose 8/6 mm, AF 10, Operating pressure max. 18 bar, nickel-plated brass
Union elbows
Nickel-plated brass, »value line« Series

Adjusting ring DIN 705 A set screw with slot bore 63mm stainless steel 1.4305
Material: 1.4305.Light-duty series. With set screw DIN EN 27 434 made from stainless steel.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC,
Article ID: 62399063

Metric threaded bar DIN 976-1 A (ex DIN 975) M4 x 1m long right handed steel 4.8 zinc-plated
Material: Steel, strength 4.8, zinc plated. Threaded bars
according to DIN 976-1 shape A (ex DIN 975), with metric ISO thread.
Length 1 m.

Threaded bars in standard quality, for light loads.

Right-handed thread.

Article ID: 65000400

150 mm White
TII0150R300601
SKU: TII0150R300601
Stock: 0
Thickness: 0.6 mm
Roll length: 30 m
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Foot mounting for worm geared motor HMD/I gearbox size 085 width 180mm overall height 236.5mm
Material: Steel sheet, zinc plated. Retrofit kit: Foot mounting for geared motor HMD/I. The position of the feet can be changed by 4x90° (Size 063: 8x 45°). 8 mounting screws are included in the delivery (4 screws per side).

Article ID: 43808300

Worm wheel made of cast iron GG25 module 4 20 teeth double-thread right hand
Material: GG25, with milled out, hollow teeth. With double-sided hub. Double-thread worm gears to be paired with double-thread worms. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°. Efficiency: approx. 0,67. Not self-locking.
Article ID: 31050700

2/2-way solenoid valve »2W«, Brass, NC, pilot operated, 230 V, 50 Hz, Medium temperature max. 80 °C/90 °C, G 1/2, PN 0.5 - 10 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.

Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 4 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Screw-in hose connector G 3/8 o. for hose I.D. 8 Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Full stroke safety valve DN 8, Brass, Operating temperature -25 °C to 180 °C, G 1/4, AF 20, Trigger pressure 47.5 bar, Type tested
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Replacement parts set for dirt strainers made of red brass, Screen and seal, Mesh width 0.6 mm, for connection size 1/4, 3/8

Elbow 2, 90°, long, Rp 3/4 IT, Rp 3/4 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

3/2-way valve »Blue Series«, Plug connector, for hose exterior Ø 8 mm, Working pressure max. 15 bar, Plastic / nickel-plated brass
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pipe double nipple 23, ET/ET, Black steel, R 1/4, Length 60.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Spur gear made of polyacetal resin die-cast with hub module 0.5 75 teeth tooth width 3mm outside diameter 38.5mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28107500

Adjusting ring DIN 705 A set screw with slot bore 65mm stainless steel 1.4305
Material: 1.4305.Light-duty series. With set screw DIN EN 27 434 made from stainless steel.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC,
Article ID: 62399065

0.5 mm 10 m
FII0620R100501
SKU: FII0620R100501
Stock: 0
Roll width: 620 mm
Because every application requires a different flexible magnetic sheet, we have various magnetic films and the knowledge to provide the right advice. Magnetic sheet with or without white top layer, self-adhesive or not, extra high magnetic force, thin or thick. For indoor and outdoor use.The question remains, what do you want to use magnetic sheet for? Let us know and we’d be glad to advise you on the right magnetic sheet for your application.

Punch, cut, plot or slice
Resistant to water and UV radiation
Suitable for advertising and promotion
Suitable for graphics and in-store-retail
Moveable, reusable and non-scratch

Application

What can I use magnetic sheet for?

Magnetic sheet attaches to any steel surface, such as a car or warehouse shelving. The material is flexible and allows for easy trimming, cutting, plotting or punching. The magnetic properties are retained. Because it is so easy to bend, it adheres to both flat and curved surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
Magnetic sheet is suitable for digital printing and screen-printing. Optionally, a special topcoat makes the magnetic sheet writeable with chalk or a whiteboard pen, and is dry erasable.
 
Applications: graphic prints and in-store communication, wall coverings, stand construction, warehouse shelving, signage, magnetic advertising, POS materials, planning boards, technical and industrialëapplications.

Composition

What is magnetic sheet?

Magnetic sheet is made of magnetic powder, composite rubber and other materials.
Our magnetic sheet is free of hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion, rolling or injection are processing techniques of rubber bonded magnetic powder. This creates soft, plastic-bound and flexible magnets such as magnetic sheet on a roll, magnetic strip in special shapes. The standard magnetic sheet colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible.

Storage and processing

How to store magnetic sheet

Store magnetic sheet in closed packaging, horizontally at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic sheet out of direct sunlight.
Shelf life is 12 months.
 
The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking. Always roll magnetic sheet with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer.
 
Process magnetic sheet at a temperature between 15 and 30 °C and humidity of 30% to 60%.
Process material in opened packaging within 1 month.
 
Magnetic sheet is easy to cut and punch with scissors, knife or cutting device.

FAQs

Magnetic sheet FAQs

Which magnetic sheet is suitable for car advertising?
A 0.8 mm thick magnetic sheet has sufficient adhesion for use on cars. Moreover, this material is very flexible for a good connection to a surface that is a little convex. All our foils are UV coated and do not scratch the surface, provided that they are applied on a clean and dry surface.
 
How do I clean magnetic sheet?
With a soft clean cloth and possibly water with detergent.
 
How much adhesive force does magnetic sheet have?
The strength of magnetic sheet is measured in a special test environment, perpendicular to the surface, with fixed factors such as steel thickness, steel grade and air gap. Thickness of the magnetic sheet, type of magnetic sheet, polarity and air gap are influencing factors. For technical and industrial applications, it is recommended to test the adhesive force.
 
Ask us for advice. Call one of our staff: +31 (0)40 221 3283 or send an e-mail.

Round flange trapezoidal nut Tr.36 x 6 single-start right material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Tolerance zone 7H.
Article ID: 64413600

2/2-way solenoid valve »2W«, Brass, NC, pilot operated, 24 V DC, Medium temperature max. 80 °C / 90 °C, G 1/2, PN 0.5 - 10 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.

Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 63, Stroke 900, G 3/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Screw-in hose connector, G 3/8 o., for hose I.D. 10, Stainless steel, Max. working pressure 60 bar, Max. operating temp. 150 °C

Full stroke safety valve DN 8, Brass, Operating temperature -25 °C to 180 °C, G 1/4, AF 20, Trigger pressure 48 bar, Type tested
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Multi-distributor, Plug nipple 6 mm »Blue Series« 4-fold, for hose exterior Ø 4x4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Elbow 41, 45°, Rp 3/4 IT, Rp 3/4 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in L-fitting »metallica«, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Pipe double nipple 23, ET/ET, Black steel, R 1 1/4, Length 100.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Adjusting ring DIN 705 A set screw with slot bore 70mm stainless steel 1.4305
Material: 1.4305.Light-duty series. With set screw DIN EN 27 434 made from stainless steel.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC,
Article ID: 62399070

Bevel gear made of steel module 4 30 teeth i=2:1 milled
Material: up to product no. 36105700: 11SMnPb30. From product no. 36106000: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module, with a different number of teeth of the same ratio.
Article ID: 36185700

0.6 mm 10 m
FII0620R100601
SKU: FII0620R100601
Stock: 0
Roll width: 620 mm
Because every application requires a different flexible magnetic sheet, we have various magnetic films and the knowledge to provide the right advice. Magnetic sheet with or without white top layer, self-adhesive or not, extra high magnetic force, thin or thick. For indoor and outdoor use.The question remains, what do you want to use magnetic sheet for? Let us know and we’d be glad to advise you on the right magnetic sheet for your application.

Punch, cut, plot or slice
Resistant to water and UV radiation
Suitable for advertising and promotion
Suitable for graphics and in-store-retail
Moveable, reusable and non-scratch

Application

What can I use magnetic sheet for?

Magnetic sheet attaches to any steel surface, such as a car or warehouse shelving. The material is flexible and allows for easy trimming, cutting, plotting or punching. The magnetic properties are retained. Because it is so easy to bend, it adheres to both flat and curved surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
Magnetic sheet is suitable for digital printing and screen-printing. Optionally, a special topcoat makes the magnetic sheet writeable with chalk or a whiteboard pen, and is dry erasable.
 
Applications: graphic prints and in-store communication, wall coverings, stand construction, warehouse shelving, signage, magnetic advertising, POS materials, planning boards, technical and industrialëapplications.

Composition

What is magnetic sheet?

Magnetic sheet is made of magnetic powder, composite rubber and other materials.
Our magnetic sheet is free of hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion, rolling or injection are processing techniques of rubber bonded magnetic powder. This creates soft, plastic-bound and flexible magnets such as magnetic sheet on a roll, magnetic strip in special shapes. The standard magnetic sheet colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible.

Storage and processing

How to store magnetic sheet

Store magnetic sheet in closed packaging, horizontally at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic sheet out of direct sunlight.
Shelf life is 12 months.
 
The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking. Always roll magnetic sheet with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer.
 
Process magnetic sheet at a temperature between 15 and 30 °C and humidity of 30% to 60%.
Process material in opened packaging within 1 month.
 
Magnetic sheet is easy to cut and punch with scissors, knife or cutting device.

FAQs

Magnetic sheet FAQs

Which magnetic sheet is suitable for car advertising?
A 0.8 mm thick magnetic sheet has sufficient adhesion for use on cars. Moreover, this material is very flexible for a good connection to a surface that is a little convex. All our foils are UV coated and do not scratch the surface, provided that they are applied on a clean and dry surface.
 
How do I clean magnetic sheet?
With a soft clean cloth and possibly water with detergent.
 
How much adhesive force does magnetic sheet have?
The strength of magnetic sheet is measured in a special test environment, perpendicular to the surface, with fixed factors such as steel thickness, steel grade and air gap. Thickness of the magnetic sheet, type of magnetic sheet, polarity and air gap are influencing factors. For technical and industrial applications, it is recommended to test the adhesive force.
 
Ask us for advice. Call one of our staff: +31 (0)40 221 3283 or send an e-mail.

Spur gear made of polyketone die-cast with hub module 0.5 54 teeth tooth width 3mm outside diameter 28mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28105401

V-belt pulley material aluminium profile XPZ, SPZ and Z (10) 2 grooves nominal diameter 315mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15023100

Trapeziodal-threaded spindle DIN 103 Tr.18 x 4 x 1000mm long single-start left material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099418

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 20, Stroke 75, G 1/8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Compressed air and water hose NR / SBR, black, Temperature range -20 °C to 70 °C, Hose Ø 17x9, PN max. 20 bar, Roll of 50 m
Robust yet flexible hose type for high pressure loads.
The hose cover resists the temporary influence of oil and is non-abrasive and weatherproof.

Straight screw-in fitting, Soft seal, G 3/8, Pipe exterior Ø 6 mm, PN max. 315 bar, Stainless steel 1.4571
Version with parallel thread and soft seal made of NBR.

Push-in L-fitting, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Reducing piece POM, Supports 22 mm, for hose exterior Ø 18 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.