Ball screw spindle rolled 20x5mm length 695mm
Material: Bearing steel 100Cr6, No. 1.3505, rolled. Tensile strength 1570 N/mm², Brinell hardness 207 HB.• Rolled ball screw spindle.• To be combined with Maedler® flanged ball screw nuts and cylindrical ball screw nuts.• Pitch accuracy 52 μm/300 mm (T7).• Straightness 0,1 mm/m.• Special lengths and spindle end reworking against extra charge.Temperature range: -20°C to +80°C (for short time to +110°C).Note: Please refer to the mounting- and operating instruction. Before use, the nut and the spindle have to be lubricated. For grease lubrication, normal roller bearing grease is recommended. The lubricant consumption depends on the condition of use.
Article ID: 64020051

5/3-way valve man. 90° lever monostable mid-position pressurisedG1/4 Operat. pressure max. vacuum 10bar Operat. temp.-10°C to 60°C
These pilot valves are also suitable for max. vacuum 10 bar.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0-16 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Throttle check valve »Blue Series«, Discharge throttle, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 10, Stroke 200, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Head nut for cover / floor, for round cylinder (not ISO 6432), Piston Ø 32, M30x1.5
Head nut for cover / base

Straight hose connection supports, for hose I.D. 25 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Reducing nipple short type G 1 1/4 o., G 1 i. AF 50 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Push-in cartridge »Blue Series«, can only be pressed in plastic, for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

40 mm White
TII0040R100601
SKU: TII0040R100601
Stock: 0
Thickness: 0.6 mm
Roll length: 10 m
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Bush EP22 bore 8mm outer diameter 10mm length 10mm colour: white
Material: Thermoplast polybutylenterephthalat, modified (PBT + PTFE), white. Plain bearing bush made from thermoplastic with high dimension accuracy. Low friction. Specially suited for dry-running and for use at very low up to middle high temperatures. Good price/perfomance ratio with high dimension accuracy. Low friction, suitable also for lubrication-free running. Temperature range -50ºC bis + 170ºC.Operating Conditions: dry : very good. oiled: good. water: very good. field of aplication:Domestic appliances, chemical equipment, office equipment, sports equipment, automotive (pedals, steering, axes) and many more.

Article ID: 62720810

Spur gear shaft made from steel with one-sided hub module 2 23 teeth toothed length 200mm total length 250mm outside diameter 50mm
Material: C45. With one-sided hub, milled, straight teeth. Pressure angle 20°.
Article ID: 24152300

Precision levelling adjuster with locknut MN 686.2 50-22.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For parall surfaces. Larger overall height with more adjustment travel. With lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68625500

Spiral hose coupling set, Safety coupling I.D. 7.4, Polyamide, Hose Ø 8x6, PN at 23 °C max. 19 bar, Length 5.0 m
For safe and effective flow.

Thanks to their small coil diameter, they are compact, easy to handle and lightweight.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0-40 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

3/2-way miniature valve, Mechanical, Tappet, NC, Connection 4 mm (side), Operating pre. 0.5-10 bar, Operating temp. -10°C to 60°C
Miniature valves, 3/2-way type, NC or NO.

Straight screw-in fitting, R 3/4, Pipe exterior Ø 18 mm, PN max. 160 bar, Stainless steel 1.4571

Mini ball valve, Rotating handle, nickel-plated brass, Medium/ambient temp. -10 °C to 80 °C, Rp 1/4 IT, DN 5.5, PN max. 10 bar

Bracket 94, 90°, ET/ET, R 1/2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Adjustable T screw fitting, cone seal, 360° swivel range, female nut M16x1.5 i., Pipe ext. Ø 10, PN max. 315 bar, galvanised steel

Angled piece, exterior / exterior, M5, AF 9, Operating pressure max. 60 bar, Operating temp. max. 150 °C, nickel-plated brass

Adjusting ring DIN 705 A set screw with slot bore 48mm stainless steel 1.4305
Material: 1.4305.Light-duty series. With set screw DIN EN 27 434 made from stainless steel.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC,
Article ID: 62399048

50 mm White
TII0050R100601
SKU: TII0050R100601
Stock: 0
Thickness: 0.6 mm
Roll length: 10 m
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Bush EP22 bore 10mm outer diameter 12mm length 6mm colour: white
Material: Thermoplast polybutylenterephthalat, modified (PBT + PTFE), white. Plain bearing bush made from thermoplastic with high dimension accuracy. Low friction. Specially suited for dry-running and for use at very low up to middle high temperatures. Good price/perfomance ratio with high dimension accuracy. Low friction, suitable also for lubrication-free running. Temperature range -50ºC bis + 170ºC.Operating Conditions: dry : very good. oiled: good. water: very good. field of aplication:Domestic appliances, chemical equipment, office equipment, sports equipment, automotive (pedals, steering, axes) and many more.

Article ID: 62721006

timing bar L 3/8" (9.525mm) 30 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A. Profile L = 3/8" = 9.525 mm.
Article ID: 18293000

Track for linear guide DA 0116 RC aluminium length 1200mm
Material: Track made from aluminium.Carriage: Stainless steel housing with plastic sealings.On choice: With stainless steel balls (greased) or polymer balls (grease free). All parts have to be ordered seperately.Linear guide for universal use.Video clip (3 minutes) for illustrating Five track lenghts on choice (for to cut by the customer). Tracks without boreholes, for customized mounting holes. Several carriages can be used on one track. Resistant against corrosion and dirt. long service life, tested to 100,000 meters of travel distance. Temperature range: -20°C to +70°C. 649 905 01 = Carriage with stainless steel balls.649 905 02 = Carriage with polymer balls.649 905 03 = Pair of end stops (2 piece with 2 screws for central fixing).649 905 06 = Track, length approx. 6 m.   649 905 12 = Track, length approx. 12 m. 649 905 18 = Track, length approx. 18 m. 649 905 24 = Track, length approx. 24 m.   649 905 36 = Track, length approx. 36 m, with mounting holes.
Article ID: 64990512

Pressure regulator, continuous pressure supply »multifix«, Size 3, G 1/2, Input pressure max. 16 bar, Control range 0.1 - 3 bar
Diaphragm pressure regulators with self-relieving design for mounting side by side.
The pressure setting can be locked by pushing the button down.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 6 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

OR valve, 3 x G 1/4, Operating pressure 2 - 10 bar, Temperature range -10 °C to 80 °C, Aluminium
The valve has two inlets and one outlet. A signal appears at the outlet when the left or right inlet is pressurised. If the pressure at the two inlets is different, the stronger of the two signals appears at the outlet.

Full stroke safety valve DN 8, Brass, Operating temperature -25 °C to 180 °C, G 1/4, AF 20, Trigger pressure 41 bar, Type tested
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Pipe double nipple 23, ET/ET, Black steel, R 2 1/2, Length 120.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Nipple I.D. 5, brass bright, for hose 6x4, Coupling nut, kink protection spring, Operating pressure 0-35 bar, Temp. -20°C to 100°C

Throttle check valve, in block shape, Anodised aluminium, Operating temperature -10 °C to 70 °C, G 1/8, PN max. 10 bar
These valves are restricted in the flow direction and have free passage in the opposite direction.

Angled piece, interior / interior, M5, AF 9, Operating pressure max. 60 bar, Operating temp. max. 150 °C, nickel-plated brass

50 mm White
TII0050R300601
SKU: TII0050R300601
Stock: 0
Thickness: 0.6 mm
Roll length: 30 m
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Clevis DIN 71752 size 8 x 16 right handed steel zinc-plated
Material: Steel zinc-plated. Design G: without bolt. Thread: Gewindeausführung rechts = thread right-handed. Gewindeausführung links = thread left-handed. Clevis with ES-bolt can be used as clevis joint. * Size 20 is not part of the DIN.
Article ID: 63720700

timing bar XL 1/5" (5.08mm) 43 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A. Profile XL = 1/5" = 5.08 mm.
Article ID: 18094300

Pressure regulator, continuous pressure supply »multifix«, Size 3, G 1/2, Input pressure max. 16 bar, Control range 0.2 - 6 bar
Diaphragm pressure regulators with self-relieving design for mounting side by side.
The pressure setting can be locked by pushing the button down.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0-10 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Double threaded nipple, Conical, R 1 1/2 a., R 3/4 a., AF 50, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Full stroke safety valve DN 8, Brass, Operating temperature -25 °C to 180 °C, G 1/4, AF 20, Trigger pressure 43.4 bar, Type tested
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Hose sleeve with ball nipple, for hose I.D. 25, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

T-piece 130, IT/IT/IT, Rp 3/8, T-branch reducing Rp 1/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galva.
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Reducing nipple, Short design, G 1 1/2 ET, G 3/4 IT, AF 55, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Push-in fitting 45° »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Spur gear made of stainless steel 1.4305 with hub module 3 40 teeth tooth width 25mm outside diameter 126mm
Material: Stainless steel 1.4305

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.


Article ID: 23399040

75 mm White
TII0075R300601
SKU: TII0075R300601
Stock: 0
Thickness: 0.6 mm
Roll length: 30 m
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Slide rail DZ 9308 single rail left hand slide length 559mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold singly (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Single slides available (left or right). Lengths to 1.5 meters. Lock-in in closed position. Lock-out in open position. Front lever lock releaze. Only for vertical mounting. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles (to 180 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note These slides are available separately. To lock both sides, you need a left slide 9308 and a right slide 9308. If you want to lock only one side, you can combinate it with a slide 9301-E. Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905222

Pressure regulator, continuous pressure supply »multifix«, Size 3, G 1/2, Input pressure max. 16 bar, Control range 0.5 - 10 bar
Diaphragm pressure regulators with self-relieving design for mounting side by side.
The pressure setting can be locked by pushing the button down.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line.

Pressure gauge, CrNi steel, Safety design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 1.6 bar, Ø 100
Bourdon-tube pressure gauge (safety housing), CrNi steel type, with solid baffle wall and blow-out (safety housing).

Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Bushing with exterior hexagonal, G 1 1/4, AF 50, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Full stroke safety valve DN 8, Brass, Operating temperature -25 °C to 180 °C, G 1/4, AF 20, Trigger pressure 43.5 bar, Type tested
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Push-in L-fitting »Blue Series«, rotating, Rc/R 3/8 i./o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Angled distributor 221, IT/IT/IT, Rp 1/2, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Mounting bracket with 2 screws

Push-in fitting 45° »Blue Series«, rotating, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Adjusting ring DIN 705 A set screw with slot bore 56mm stainless steel 1.4305
Material: 1.4305.Light-duty series. With set screw DIN EN 27 434 made from stainless steel.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC,
Article ID: 62399056

Gear rack made of stainless steel module 3.18 (metrical pitch 10mm) tooth width 30mm height 30mm length 250mm
Material: Stainless steel 1.4305. Milled teeth. Precisely
Straightened. Straight teeth. Pressure angle 20°. Tooth quality 8d25
modelled on DIN 3962, 3967, 3968. Pitch 5 mm = Module 1.59. Pitch 10 mm
= Module 3.18. The teeth on the gear racks are manufactured using an
overhead milling cutter. This leads to negative tolerances for dimension
a and h0: At pitch 5mm: -0,2 mm. At pitch 10mm: -0,3 mm. From Module 2,
except for nominal length 500 mm, cut for continuous linking. * Length =
Nominal length. The real length is roughly one multiple of the pitch.

Article ID: 21099601

Flanged bush similar to DIN 1850 V (DIN 4379 F) sintered bronze bore 8mm outer diameter 12mm flange diameter 16mm length 8mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. Edges chamfered at 45°, at choice of the manufacturer. The
concentricity tolerance refers to d2. 1) no statement regarding the
surface roughness according to DIN 3141 (prenorm) can be given due to
the porous structure of the sintered metal. Technical Data: Surface
pressure: max. 35 N/mm², depending on speed and diameter. Temperature
range: -20°C to +120°C. Dimension r: For bores 3 - 8 mm = 0.3 mm, bores
9 - 22 mm = 0.6 mm, bores 25 - 40 mm = 0.8 mm Tolerances: Inner
diameter d1: F8 / G8. Outer diameter d2: s8. Flange diameter d3: js13.
Length b1:+/-0.1mm.Flange thickness b2: js14.

Article ID: 62351200

100 mm White
TII0100R300601
SKU: TII0100R300601
Stock: 0
Thickness: 0.6 mm
Roll length: 30 m
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.