Safety coupling I.D. 7.6, »stream line«, galvanised steel / brass, for hose 13.5x9.5, Operating pressure max. 16 bar
High-quality, robust and durable, one-hand quick disconnect safety couplings, with very high flow rates and only a small pressure drop.

The coupling is released fully automatically in two steps. Air is relieved from the coupling before it is completely disconnected. The plug is only disconnected from the coupling if the residual pressure has dropped below 0.3 bar. The dreaded "whiplash effect" is thus avoided and the risk of injury virtually eliminated.

This safety version conforms to ISO-Standard DIN EN ISO 4414.

These safety couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, manufacturing industry, workshops, automotive, mining.

Locking screw, Exterior hexagonal , flange G 1/8 Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Angled screw-in fitting, rotating, with O-ring, G 1/4 o., for hose 6/4 mm, Working pressure max. 18 bar, nickel-plated brass

Reducer, Pipe exterior Ø Female connector 25/10 mm, PN max. 400 bar, a/f1 27, a/f2 22, a/f3 46, galvanised steel
Reducer, heavy type

Push-in L-fitting »Blue Series«, rotating, M5 i., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Rubber pad for machine feet oval L=81mm
Material: Material: Rubber NBR, black, 70º +/-5º Shore A.

These oil-resistant rubber pads can be cliped into the bores of the
Maedler® machine mounts (failsafe or not failsafe). With small nubs on
the bottom side. The rubber pads enable an anti-slip and
vibration-damping placement of the machine mounts. Only for
applications, where the machine mounts don´t need to be bolted in the
ground.

Article ID: 68594099

Conveying width : 575 mm
HSC-F-500-1500-0000-00-B-B-BR
SKU: TCBC500001
Conveying length: 1500 mm
Magnet width: 500 mm
Flat magnetic slide conveyors are suitable for transporting steel parts such as punch scrap, chips, nails, bolts, recycled materials and drilling swarf.They are intended for metal and steel plants and the sheet processing industry.

Conveying width: 275 - 575 mm
Conveying length: up to 15 m

Advantages

Advantages of a flat magnetic slide conveyor:
no belt wear
requires little maintenance
no trapping of material, thanks to sealed construction
no damage to product or conveyor belt
dirt and moisture have no effect on operation
completely sealed; no external moving parts


Operation

Operation of a flat magnetic slide conveyor:

Magnets, spaced evenly along the length of a chain, are positioned beneath the stationary stainless steel slide sheet. The chain is driven.
These magnets thus move the steel parts along the slide sheet and carry them to the discharge end at the desired height.

Characteristics

Characteristics of a flat magnetic slide conveyor:
maximum conveying width: 575 mm
conveying length: as desired, up to 15 m
capacity: 14 - 42 kg/min
(for punch scrap Ø7x1; at 18 m/min; with a magnet distance of 600 mm)

Crane wheel made of C 45 with axle shaft diameter 84mm
Especially suited for heavy-duty applications, e.g. electrically controlled gates. Precisely turned from solid material; with fully sealed precision bearings. Wheel body black oxide finish. Product No. 776 004 00 and 776 005 00 with square running surface and single bearing, Product No. 776 006 00 to 776 016 00 with convex running surface and double bearing. Delivery includes all mounting material needed; axle bolt at running surface Ø 35 and 45 mm with external thread, serrated washer and hexagon nuts, other sizes with internal thread, 6 hexagon screws and washers DIN ISO 7093-1. * The wheel loads stated are derived from the dimensions and temperatures listed in the roller bearing cataloques. For product No. 776 004 00 and 776 005 00 these values are valid at a maximum operating temperature of 90°C; for higher continuous temperatures, please inquire first. ** Rails are not part of our stock. Please inquire at your steel supplier.
Article ID: 77600800

Precision pressure regulator, cont. pressure supply »FUTURA«, Size 2, G 3/8, Input pressure max. 16 bar, Control range 0.5-16 bar
Precision diaphragm pressure regulators with self-relieving design and excellent flow rates in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different pressures via a single supply line.

Pre-filter »FUTURA« with metal container and viewing tube, 0.3 µm, Size 2, G 1/2, 1.5-16 bar, Temp. -10°C to 50°C, Semi-automatic
Pre-filters in modern design for compliance with strict compressed air purity requirements.
Pre-filters are used to separate solid impurities up to 0.3 µm from compressed air and gases.

Tempered coupling DN 6, Exterior thread, Blocking valve, Brass, M14x1.5 45°, Operating pressure max. 15 bar, Temp. -20°C to 160°C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Bi-metallic thermometer, High quality design, Connection rear, for protective pipe L1=100 mm/L2=80 mm, Display range 0°C to 250°C
Applications: Extremely versatile design for use in machine, vessel, pipeline and plant construction as well as for heating systems.

A thermowell (removable with locking screw) is required.

Push-in T-connector »Blue Series«, for hose exterior Ø 12 mm, Working pressure max. 15 bar, Plastic / nickel-plated brass
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in fitting »Blue Series«, round, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Needle valve, Nickel-plated brass, IT/IT, Rp 1/4, DN 4, AF1 19, Operating temperature -10 °C to 80 °C, PN max. 18 bar

Straight push-in fitting »click-clock«, G 1/8 o., for hose exterior Ø 5 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Rod end GT DIN 12240-4 series K external thread M42x2 right maintenance-free
Material:
Outer part: Zinc-plated. Boreholes up to 12mm: free-cutting steel, turned. From boreholes 14mm: Steel C22, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K.

Thread either right-handed or left-handed. Heavy-duty rod ends for high radial and axial alternating loads.
Steel on PTFE-lining.
Maintenance-free.
Sliding speed up to 10 m/min.
Article ID: 63284000

Conveying width : 154 mm
HSC-M-090-1000-0000-00-B-B-BR
SKU: TCBD090001
Magnet width: 90 mm
Conveying length: 1000 mm
Mini-magnetic slide conveyors are suitable for transporting small parts such as punch scrap and punched products.They are intended for metal and steel plants and the sheet (steel) processing industry.

Conveying width: 154 / 314 mm
Conveying length: up to 4 m

Advantages

Advantages of a magnetic mini flat bed slide conveyor:
no belt wear
requires little maintenance
no trapping of material, thanks to sealed construction
no damage to product or conveyor belt
dirt and moisture have no effect on operation
completely sealed; no external moving parts


Operation

Operation of a magnetic mini flat bed slide conveyor:

Magnets, spaced evenly along the length of a chain, are positioned beneath the stationary stainless steel slide sheet. The chain is driven.
These magnets thus move the steel parts along the slide sheet and carry them to the discharge end at the desired height.

Characteristics

Characteristics of a magnetic mini flat bed slide conveyor:
maximum conveying width: 314 mm
conveying length: as desired, up to 4 m
capacity: 9 - 20 kg/min (punch scrap Ø7x1; 19 m/min; with 200 mm magnet spacing)

Neoprene timing belt 80 MXL 012 100 teeth Lw 203.20mm belt width 3.2mm
Material: Neoprene with glas-fibre tensile member. Teeth surface fabric-coated. Timing belt with inch dimensions, classical shape with trapezoid teeth. Profile MXL = 0,08" = 2.032 mm. Belt width 012 = 3.2mm. Temperature range -20º to +100ºC.
Article ID: 18164000

timing bar T2.5 84 teeth length 140mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16098400

Precision pressure regulator, cont. pressure supply »FUTURA«, Size 2, G 1/2, Input pressure max. 16 bar, Control range 0.5-16 bar
Precision diaphragm pressure regulators with self-relieving design and excellent flow rates in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different pressures via a single supply line.

2/2-way solenoid valve brass, NO, directly operated, 230 V, 50 - 60 Hz, Medium temperature -15 °C to 100 °C, G 1/4, PN 0 - 9 bar
Standard series, proven over many years, available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Tempered coupling DN 6, Exterior thread, Brass 2.0401, G 1/4 45°, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Extension pipe without nozzle, curved 150 mm, Aluminium, for use with safety nozzles standard design

Reducing nipple, Hexagonal, G 1 o., G 3/4 i., AF 38, Working pressure max. 20 bar, Stainless steel 1.4408

Pipe double nipple 23, ET/ET, Black steel, R 1 1/2, Length 40.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Needle valve, Nickel-plated brass, IT/ET, Rp/R 1/4, DN 4, AF1 19, Operating temperature -10 °C to 80 °C, PN max. 18 bar

Worm thread - hose clamp »blow line«, Stainless steel (W 5) 1.4401, Belt width 9.0 mm, Clamping range 90.0 - 110.0 mm

Rod end GT DIN 12240-4 series K external thread M42x2 left maintenance-free
Material:
Outer part: Zinc-plated. Boreholes up to 12mm: free-cutting steel, turned. From boreholes 14mm: Steel C22, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K.

Thread either right-handed or left-handed. Heavy-duty rod ends for high radial and axial alternating loads.
Steel on PTFE-lining.
Maintenance-free.
Sliding speed up to 10 m/min.
Article ID: 63294000

Conveying width : 314 mm
HSC-M-250-1000-0000-00-B-B-BR
SKU: TCBD250001
Magnet width: 250 mm
Conveying length: 1000 mm
Mini-magnetic slide conveyors are suitable for transporting small parts such as punch scrap and punched products.They are intended for metal and steel plants and the sheet (steel) processing industry.

Conveying width: 154 / 314 mm
Conveying length: up to 4 m

Advantages

Advantages of a magnetic mini flat bed slide conveyor:
no belt wear
requires little maintenance
no trapping of material, thanks to sealed construction
no damage to product or conveyor belt
dirt and moisture have no effect on operation
completely sealed; no external moving parts


Operation

Operation of a magnetic mini flat bed slide conveyor:

Magnets, spaced evenly along the length of a chain, are positioned beneath the stationary stainless steel slide sheet. The chain is driven.
These magnets thus move the steel parts along the slide sheet and carry them to the discharge end at the desired height.

Characteristics

Characteristics of a magnetic mini flat bed slide conveyor:
maximum conveying width: 314 mm
conveying length: as desired, up to 4 m
capacity: 9 - 20 kg/min (punch scrap Ø7x1; 19 m/min; with 200 mm magnet spacing)

Clevis joint similar DIN 71752 size 4 x 16 type KL right handed aluminum black anodized
Material: Clevis and bolt aluminium, anodized black.With KL-Retainer from steel, bright zinc plated.Thread: Gewindeausführung rechts = thread right-handed.
Article ID: 63766002

Ball head precision levelling adjuster MN 686.8 60-26.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For non-parall surfaces up to 4° slope. Larger overall height with more adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68687000

Ball head precision levelling adjuster MN 686.4 60-33.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For non-parall surfaces up to 4° slope. Lower overall height with short adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68647500

Precision pressure regulator, cont. pressure supply »FUTURA«, Size 2, G 3/8, Input pressure max. 16 bar, Control range 0.1 - 1 bar
Precision diaphragm pressure regulators with self-relieving design and excellent flow rates in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different pressures via a single supply line.

Compact cylinder »ACP«, double-acting, Piston Ø 100, Stroke 30, Connection G 1/4, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Tempered coupling DN 6, Exterior thread, Brass 2.0401, G 1/4 90°, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Protective pipe for screw-in, with set screw, G 1/2, L1 = 100 mm, Operating pressure max. 25 bar, CrNi steel 1.4571
For bimetallic thermometers in the »High quality« series.

Reducing nipple, Hexagonal, G 1 o., G 1/2 i., AF 37, Working pressure max. 20 bar, Stainless steel 1.4408

Cutting / seal ring, for hose 4/6 mm, Working pressure max. 10 bar (20°C)/max. 1 bar (170°C), PEEK (cutting ring)/PTFE (seal ring)
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Needle valve, Nickel-plated brass, ET/ET, R 1/4, DN 4, AF1 19, Operating temperature -10 °C to 80 °C, PN max. 18 bar

Screw-in hose connector, G 1/8 o., for hose I.D. 9 mm, AF 14, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

0.8 N Self-adhesive with foam
GM23000102A
SKU: GM23000102A
Stock: 0
Thickness: 1.5 mm
Roll width: 12.7 mm
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Clevis joint similar DIN 71752 size 4 x 16 type SL right handed aluminum black anodized
Material: Clevis and bolt aluminium, anodized black.With SL-Retainer from steel, bright zinc plated. Thread: Gewindeausführung rechts = thread right-handed.
Article ID: 63766402

Precision single universal joint WER DIN 808 simple, bore 25H7
stainless steel 1.4301 total length 140mm outer diameter 50mm
Material: Stainless steel 1.4301 Max. Operating Angle 45°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques amount to only about 50% of the standard version WE. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199250

Precision pressure regulator, cont. pressure supply »FUTURA«, Size 2, G 1/2, Input pressure max. 16 bar, Control range 0.1 - 1 bar
Precision diaphragm pressure regulators with self-relieving design and excellent flow rates in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different pressures via a single supply line.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 63, Stroke 50, G 3/8, Working pressure 1.5 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Tempered coupling DN 6, Exterior thread, Brass 2.0401, M14x1.5 45°, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Protective pipe for welding, with set screw, L2 = 80 mm, Operating pressure max. 25 bar, CrNi steel 1.4571
For bimetallic thermometers in the »High quality« series.

Push-in T-connector »click-clock«, for hose exterior Ø 10 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 80 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

1/3 Tube fitting, G 3/4 x 19 mm, taper seat, with collar, heavy-duty type, Brass with a bare metal surface

T-multi-distributor »Blue Series«, rotating, G 1/4 o., for hose exterior Ø 4x8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in supports, R 1/2 o., for hose I.D. 12 mm, AF 22, Over-pressure max. 22 bar, Temperature range -40°C to 90°C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Round gear rack made of stainless steel 1.4305 module 3 diameter 30mm h9 length 500mm
Material: Stainless steel 1.4305.
Outside diameter = h9 drawn.

Straight teeth, milled.
Pressure angle 20°. Tooth quality 8d25 modelled on DIN 3967.

The teeth on the gear racks are manufactured using an overhead milling cutter.
This leads to negative tolerances. Dimensions ha and h0:
up to Module 2: -0,2 mm.
Module 2,5 - 4: -0,3 mm.


Article ID: 24399631

0.8 N Self-adhesive with foam
GM23001600
SKU: GM23001600
Stock: 0
Thickness: 3 mm
Roll width: 20 mm
Magnetic strip - magnetic tape or magnetic band - available with or without coloured layer, adhesive or not, extra magnetic force, thin or thick. Because every application requires a different type of flexible magnetic strip, we have a wide selection. The question remains: what are you going to use it for?

For presentation, display or hanging
Deliverable from stock
Available in various adhesive options
Available in various widths

Application

What do you use the magnetic strip for?

The magnetic strip is flexible and easy to trim, cut and process. The magnetic properties are retained. Because it is flexible, it attaches to both flat and curved steel surfaces.
The magnetic side has a UV coating. This prevents scratches on the surface.
A special self-adhesive makes the magnetic tape suitable for processing on various surface types such as wood, metal, paper and plastics. For indoor and outdoor use.
Available as a match-pole application: magnet on magnet for a perfect fit. The magnetic pole pattern of the both match-pole tapes fit together perfectly. This means both parts fit exactly. The magnetic multipole tapes are a set and are characterized by a smooth surface or groove.
 
Various grades of magnetic strip
Magnetic strip is available in isotropic and anti-isotropic grades. Magnetic material that is not pressed in a magnetic field is called isotropic. An isotropic magnet material can be magnetized in any direction. Isotropic magnets have a lower tensile force than anisotrope magnets.
One-sided multipole or axially magnetized. If the magnetic poles are located on one side of the magnetic material, this is called single-sided multipole magnetized.
The magnetic strip tensile force depends on implementation.
 
Applications: stand construction, technical applications, displays and door profiles.

Composition

What does magnetic strip consist of?

Magnetic strip is made of magnetic powder, composite rubber and other materials. Our magnetic strip does not contain hazardous chemicals or heavy metals. It complies with the EN71 standard and RoHS.
 
Extrusion and rolling are processing techniques of rubber bonded magnetic powder. This creates soft flexible magnets. Magnetic tape and magnetic band on rolls are produced by rolling. Magnetic strip or magnetic profile in special shapes are produced by extrusion.
 
The standard colour is dark brown. If desired, a coloured top layer of vinyl, a sticker or another top layer is possible. Magnetic strip is usually one-sided multi-pole magnetized.

Storage and processing

How to store magnetic strip

Store magnetic strip in the closed packaging, flat, and at a temperature between 10 and 30 °C. The humidity should be between 20% and 70%. Keep magnetic strip out of direct sunlight. Shelf life is 12 months. The material can be rolled up at a temperature of 20 °C to a diameter of 12 mm without breaking.
Always roll magnetic strip with the coloured or adhesive side on the outside. This will prevent creasing and cracking in the top layer. Process magnetic strip at a temperature between 15 and 30 °C and a humidity of 30% to 60%. Process material in opened packaging within 1 month.

FAQs

Magnetic strip FAQs

If you have a question, we’d be glad to answer it.
Send us an e-mail or call one of our staff: +31 (0)40 221 3283.

Grub screw DIN 6332 with thrust point thread M6 length 50mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, black oxide finish. Type S: With slot. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400700

Ball pillow block bearing SSUCP 210 bore 50mm housing and bearing stainless steel
Material: Housing: Stainless steel 1.4305 (X5CrNi18-10, AISI 304). Rolling bearing: Stainless steel 1.4125 (X105CrMo17, AISI 440 C), lubricated ith grease FM 222 for food processing machinery, with registration FDA, CIFA, KPF2K-20, NSF H1. Temperature range: -20°C to +90°C (for short time up to +120°C).The rolling bearing can be swiveled when mounting to compensate shaft misalignement. The shaft will get fastened with 2 setscrews.Lubricated for life at normal operating conditions. Re-lubricating is possible.Delivery with stainless steel grease nipple.
Article ID: 62599150

Spoked handwheel stainless steel 1.4308 solid version B/G with handle diameter 200mm
Material: Wheel body: Cast stainless steel 1.4308. Rim turned, matt blasted. At version B/G: Handle Duroplast PF31, black, glossy finish. Spindle: Stainless steel 1.4305.Version B/A: Without thread, without cylindrical handle.Version B/G: With revolving cylindrical handle.Easy to clean.Keyway available at extra charge.
Article ID: 67099620

Precision pressure regulator, cont. pressure supply »FUTURA«, Size 2, G 3/8, Input pressure max. 16 bar, Control range 0.1 - 2 bar
Precision diaphragm pressure regulators with self-relieving design and excellent flow rates in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different pressures via a single supply line.

5/2-way valve, electropneum., monostable, G 1/2, DN 15, 230 V, 50 Hz, Operating pre. 2.5-10 bar, Operating temp. -10°C to 60°C