Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ125, Stroke80, G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Front or floor flange, ISO 21287, Piston Ø 32, with 4 screws
Front or rear flange

Round cylinder TP (ISO 6432) double-acting, Piston Ø 25, Stroke 10, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 60 °C
Inexpensive standard version with aluminum pipe and magnet piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight push-in fitting »Blue Series«, round, G 1/2 o., for hose exterior Ø 14 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Plug-in connector for couplings I.D. 10, Hardened / nickel-plated steel, Sleeve I.D. 13, Operating pressure 0 - 35 bar

Quick-connect coupl. I.D. 7.2, locking on both sides, Bright brass, Sleeve I.D. 9, Operat. pressure 0-35 bar, Temp. -20°C to 100°C
Couplings, stems and plugs are fitted with a valve.
Connection: Both valves open and the medium is allowed to pass.
Disconnection: Both valves close and the medium is prevented from escaping.

Areas of application: Pneumatic system, machine and plant engineering, Measurement, monitoring and control systems, Manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive, food technology, aerospace.

Replacement seal made of NBR, for Kamlok couplings made of stainless steel, for coupling DN 50 (2")

Spur gear made of polyacetal resin die-cast with hub module 0.5 65 teeth tooth width 3mm outside diameter 33.5mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28106500

Max. stack height : 560 mm
HSS-N-PF-140x175-0600-B
SKU: TPSP126001
Stock: 12
Max. sheet thickness: 4 mm
Connections: Pneumatic: G1/8" (2x)
Spread stacked steel sheets in automated processes one by one. These pneumatically switchable sheet separators have a neodymium magnet system.So you can easily add to or swap a stack of sheets.

Pneumatically switchable
Max. stacking height 560 mm
Stainless steel enclosure
With neodymium magnets

Operation

Operation of pneumatically switchable sheet separator

A powerful magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
 
The separator contains very powerful neodymium magnets that are moved forward by compressed air in the sheet separator. This switches the sheet separator on.
The new, patented fail-safe system ensures that the sheet separator always shuts itself off once the compressed air drops. This makes this sheet separator unique in terms of safety.
 
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.


Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Metric threaded bar DIN 976-1 form A M6 x 1000mm right handed class 10.9 plain marked with white paint
Material: Steel, strength 10.9. Threaded bars according to DIN 976-1 shape A (ex DIN 975), with metric ISO thread. Length 1 m. Threaded bars with high strength. Marked with white paint. Right-handed thread.
Article ID: 65010600

Slide set DS 3557 slide length 508mm stainless steel 1.4301
Material: Stainless steel 1.4301. Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Sold by pair (1 x product no. = 1 pair of slides). Locks in open position. Fast disconnection. Pinch free disconnect for easy drawer removal. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note: Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings.

Article ID: 64903350

Rod end GEW DIN 12240-4 series E internal thread M36x3 right maintenance-free
Material: Outer part: Zinc-plated. Boreholes up to 10mm: free-cutting steel, turned. From boreholes 12mm: Steel C45, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining. Small version. Dimensions according to DIN 648 / 12240-4 series E. Thread either right-handed or left-handed. Rod ends for high radial and axial alternating loads. Steel on PTFE-lining. Maintenance-fee. Sliding speed up to 10 m/min.
Article ID: 63413500

Precision pressure regulator without pressure gauge, Free of non-ferrous metals, G 1/4, Control range 0.1 - 2 bar
Diaphragm pressure regulators containing no non-ferrous metals,
with secondary venting for applications requiring an extremely accurate working pressure.

2-way brass ball valve, Pneumat. actuation drive double-acting, Operating temperature max. 70 °C, Rp 3/4, DN 20, PN max. 40 bar
2-way cock, full bore.
Pneumatic actuators, double- or single acting version and integrated end-position feedback.

Seal set (wear part), for compact cylinder, Piston Ø 32, PU seal
Set of gasket (parts subject to wear)

Round cylinder TP (ISO 6432) double-acting, Piston Ø 20, Stroke 100, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 60 °C
Inexpensive standard version with aluminum pipe and magnet piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Push-in L-fitting »Blue Series«, rotating, R 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series«, rotating, G 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Throttle check valve »Blue Series«, Straight, R 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in fitting »Blue Series«, round, R 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Max. stack height : 100 mm
HSS-N-RD-D34-0160-B
SKU: TRSP341600
Stock *: 0
Max. sheet thickness: 3 mm
For specific applications, we have also developed a suitable sheet separator in the form of a rod.This type is very compact and easy to place into an opening in the sheet. Its round shape also makes it suitable for special contours.

Permanent magnetic
For sheets up to 3 mm thick
Max. stacking height 100 mm
Stainless steel enclosure

Operation

Sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.

Star knob similar DIN 6336 type GV Technopolymer PA6GV ø50 M10x40
Material: Thermoplast Polyamide PA6 GV, glass-fibre reinforced, impact resistant, black matt. Threaded bolt: steel, zinc-plated, chromated blue.
Article ID: 66145040

Ball joint RW bore 35H7 material steel
outer diameter 60mm total length 165mm
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63136000

Rod end GEW DIN 12240-4 series E internal thread M36x3 left maintenance-free
Material: Outer part: Zinc-plated. Boreholes up to 10mm: free-cutting steel, turned. From boreholes 12mm: Steel C45, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining. Small version. Dimensions according to DIN 648 / 12240-4 series E. Thread either right-handed or left-handed. Rod ends for high radial and axial alternating loads. Steel on PTFE-lining. Maintenance-fee. Sliding speed up to 10 m/min.
Article ID: 63433500

Short stroke cylinder, double-acting, Magnet, Piston Ø 40, Stroke 10, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Short stroke cylinder, double-acting, Magnet, Piston Ø 80, Stroke 50, G 1/4, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Bidirectional flow control valve »lineonline«, Flow both sides, Thread - hose, G 3/8, for hose Ø 8, Operating pressure max. 10 bar
Control the air intake and thus the speed of pneumatic units.

Series base plate 7-fold, M5 for mini solenoid valve 15 mm

Fitting 330, flat sealing, IT/IT, Rp/Rp 1, NBR seal, Operating temp. -20°C to 200°C, black malleable cast iron, hot-dip galv.
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

L-ring piece, for hollow screw G 3/8, for hose exterior Ø 8 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 70 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Angle flange, ISO 15552, ISO 21287, Ø50, 1 piece with 4 screws
Angle flange

Pressure gauge connection nipple, Self-sealing, made of brass, G 3/8 ET, G 1/4 IT, PN 600 bar

Pallet dimension : 1200 x 800 mm
HPA-F-F-ST-1250-0850-B
SKU: TPBC120852
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Ball joint RW bore 35H7 with keyway DIN 6885-1 on both sides outer diameter 60mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63136000N

Filter regulator »multifix« with PC container, Protective cage and press. gauge, 5 µm, Size 1, G 3/8, Input pressure max. 16 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator.
The pressure setting can be locked by pushing the button down.

Standard cylinder, ISO 15552, double-acting, Piston Ø 80, Stroke 125, G 3/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches can be mounted in two T-slots on the same side as the compressed air supply.
The version with a 125 mm bore is provided with fixing accessories on three sides as standard.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Bracket 94, 90°, ET/ET, R 1 1/2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Mist oiler »FUTURA« with PC container and protective cage, Size 1, G 1/4, Input pressure max. 16 bar, Temp. -10 °C to 50 °C
Oil-mist lubricators with excellent flow rates in modern design.
These devices can be used to top up oil automatically.
A hose must be connected to the threaded nipple on the oil bowl for this purpose.
When the oil filling button on the top of the device is pressed, a Venturi nozzle opens and sucks oil into the bowl under vacuum.

Filter element 40 µm, PE sintered, for filter and filter regulator »variobloc«, Size 2, G 1/2, G 3/4 and G 1

Reducing nipple, Hexagonal, G 1/2 o., G 3/8 i., AF 26, Working pressure max. 20 bar, Stainless steel 1.4408

Ceiling bracket with quick-connect coupling I.D. 7.2, Bright brass, G 3/8 IT, Operating pressure 0-35 bar, Temp. -20 °C to 100 °C
1, 2 or 3-way distributor pieces made of brass with a bare metal surface, pre-assembled with quick disconnect coupling DN 7.2.
Available with threaded connection inside or outside or nipple for adaptation into an existing quick disconnect coupling DN 7.2 to DN 7.8.

Angled screw-in fitting »value line«, R 1/8 o., for hose 8/6 mm, AF 10, Operating pressure max. 18 bar, nickel-plated brass
Union elbows
Nickel-plated brass, »value line« Series

Round flange trapezoidal nut Tr.30 x 6 single-start left material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Tolerance zone 7H.
Article ID: 64443000

Flanged bush similar to DIN 1850 V (DIN 4379 F) sintered bronze bore 6mm outer diameter 10mm flange diameter 14mm length 10mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. Edges chamfered at 45°, at choice of the manufacturer. The
concentricity tolerance refers to d2. 1) no statement regarding the
surface roughness according to DIN 3141 (prenorm) can be given due to
the porous structure of the sintered metal. Technical Data: Surface
pressure: max. 35 N/mm², depending on speed and diameter. Temperature
range: -20°C to +120°C. Dimension r: For bores 3 - 8 mm = 0.3 mm, bores
9 - 22 mm = 0.6 mm, bores 25 - 40 mm = 0.8 mm Tolerances: Inner
diameter d1: F8 / G8. Outer diameter d2: s8. Flange diameter d3: js13.
Length b1:+/-0.1mm.Flange thickness b2: js14.

Article ID: 62350900

Pallet dimension : 1200 x 1000 mm
HPA-F-F-ST-1250-1050-B
SKU: TPBC121052
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Slide rail DZ 9308 single rail left hand slide length 457mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold singly (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Single slides available (left or right). Lengths to 1.5 meters. Lock-in in closed position. Lock-out in open position. Front lever lock releaze. Only for vertical mounting. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles (to 180 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note These slides are available separately. To lock both sides, you need a left slide 9308 and a right slide 9308. If you want to lock only one side, you can combinate it with a slide 9301-E. Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905218

Slide set DS 2028 slide length 700mm stainless steel
Material: Slide elements: Stainless steel 1.4301 Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in closed position. Ideal for environments where mild steel might corrode. Service life 10,000 / 80,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings. Ordering details: e.g.: Product no. 649 444 30, Slides DS 2028
Article ID: 64944470

Precision pressure regulator without pressure gauge, Free of non-ferrous metals, G 1/4, Control range 0.1 - 3 bar
Diaphragm pressure regulators containing no non-ferrous metals,
with secondary venting for applications requiring an extremely accurate working pressure.

Storz adapter, Stainless steel V4A, Storz size 52-C, Tappet distance 66 mm, G 1 ET, Operating pressure max. 16 bar
High-quality series in V4A stainless steel. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Industrial plant engineering, shipbuilding, chemical industry.

Air gun with safety nozzle, Plastic, Temperature range -20 °C to 50 °C, PN max. 10 bar, Sleeve I.D. 6
For blowing out and cleaning machines, engines, bearings, sliding surfaces, bores of all kinds, hollow parts, moulds, etc.

Mist oiler »FUTURA« with PC container and protective cage, Size 1, G 3/8, Input pressure max. 16 bar, Temp. -10 °C to 50 °C
Oil-mist lubricators with excellent flow rates in modern design.
These devices can be used to top up oil automatically.
A hose must be connected to the threaded nipple on the oil bowl for this purpose.
When the oil filling button on the top of the device is pressed, a Venturi nozzle opens and sucks oil into the bowl under vacuum.

Double threaded nipple, Cyl., G 3/8 o., G 1 o., AF 38, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Push-in bulkhead L-connector »Blue Series«, M14x1, for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, Soft seal, G 1/8, Pipe exterior Ø 6 mm, PN max. 315 bar, Stainless steel 1.4571
Version with parallel thread and soft seal made of NBR.

Plug-in connector for couplings I.D. 7.2 - 7.8, bright brass, Sleeve I.D. 13, Operating pressure 0 - 35 bar, Temp. -20°C to 100°C

Locknut DIN 981 KM 4 thread M20x1
Material: Steel, min. strength 350 N/mm².These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65364000

Pallet dimension : 1420 x 1120 mm
HPA-F-F-ST-1470-1170-B
SKU: TPBC141152
Magnetic palletizers with steel housing are suitable for palletizing and depalletizing with a gantry crane.They are available in various versions - for picking up empty or filled tins, aerosols, cans and glass jars with steel lids.

For use with a gantry crane
Steel enclosure
With neodymium or ferrite magnets

Operation

Palletization magnet operation

Goudsmit magnetic palletizers use permanent magnetic force to lift and hold steel products in one go. They do this without a power supply.
Palletization magnets hold a layer of products for as long as needed.

Design

Unique design

The unique parallel mechanism of the palletization magnet guarantees a trouble-free production process, even with non-uniform loads. For example, when picking up a half layer with products.
The special Goudsmit design has a long service life, requires little maintenance and consumes little air.

Application

Applications per magnetic system
With ferrite fine pole magnet system.
For palletizing empty aerosol cans and empty tins.
Product dimensions:
aerosols: Ø45-65 mm; max. height 229 mm tins: Ø44-87 mm; max. height 116 mm.
 
With neodymium - Neoflux® - medium pole magnet system.
For palletizing large filled tins.
Product dimensions:
tins: min. Ø65 mm (up to 0.6 kg) - max. Ø230 mm (up to 5 kg).
With neodymium - Neoflux® - fine pole magnet system.
For palletizing/depalletizing extra-large filled tins and filled jars with screw lids.
Product dimensions:
screw lids: Ø34 mm (up to 0.45 kg)
screw lids: Ø42 mm (up to 0.85 kg)
screw lids: Ø56 mm (up to 1.1 kg)
screw lids: Ø82 mm (up to 2.2 kg)
screw lids: Ø110 mm (up to 4.0 kg)

Protection cap for pillow bearings TUCP TUCF TUCFL 206 closed design thermoplast white
Material: Thermoplast PBT, white.Open Design, with sealing, for shaft side or closed design.The caps fit only on the one bearing side with the setscrews and can get clipped on by hand by the customer.
Article ID: 62556330

Slide rail DZ 9308 single rail right hand slide length 457mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold singly (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Single slides available (left or right). Lengths to 1.5 meters. Lock-in in closed position. Lock-out in open position. Front lever lock releaze. Only for vertical mounting. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles (to 180 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note These slides are available separately. To lock both sides, you need a left slide 9308 and a right slide 9308. If you want to lock only one side, you can combinate it with a slide 9301-E. Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905418

timing bar T2.5 80 teeth length 140mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16098000